Видео

I have the same pump, but its branded ‘Ring’ you need to press the + button before it pumps.

First let me say I love this video, please make more. I am looking forward to seeing what else you have on your channel. I love that you pulled it all apart and explained everything. It's obvious that Honeywell did NOT want this device repaired. I'm just wondering what the time, money, & effort cost is compared to the money and time it would take to simply purchase a new one. I too hate throwing things away due to a tiny electronic part, but it sounds like if you are going to do this right you need the following: • a flat surface with enough space for the job at hand • good lighting as there are many angles inside the device • multimeter • masking tape • pencil and paper (for making notes) • small wire snips • small needle nose pliers • small (not tiny) long neck philips screwdriver • flathead screwdriver • small wire strippers • an X-acto knife • small machine lubricant / oil • heat shrink tubes • thermal fuse • thermal paper (to safely secure the copper coiling) • a soldering iron • solder • a fan (to remove the toxic fumes while soldering) But hey, Your health, your choice. • Plastic paint or fingernail polish in the wire's colors for markings what plastic hole they came out of. (red, black, yellow, white, green, & blue) And the knowledge on how to use them for this situation. If you don't have these things in your tools or work bench it would be MUCH cheaper and faster to just scrap it and pick up a new one. Either that or use this video, and some other similar videos, to teach your kids how to use the aforementioned tools and equipment to test where the problem is located, single out the issue (in case there are more than one problem) and do this repair.

Awsome videos man..great work

This video was amazing thank you so much! I am having trouble with the motor, could you please help me with that?

Thank you so much for taking the time to make and post this video. I realize a lot of people would simply replace the fan. * I am frugal The odd things like this drive me crazy. Ours is so dirty, use in a bathroom. Lots of T-paper lint inside. * Next chore, get better T-paper. ¥

So HOW did you do it sir??? Your vid skipped the whole entire demonstration... 🙅‍♀️🤦‍♀️🙍‍♀️

Good observation..

Exact same thing happened to mine! Damage to hinges and bent damper.

Well, this fix lasted for almost exactly a year. On friday morning April 5 2024 the 96 corolla would not start on an overnight where there was a very wet above freezing snow storm. So now maybe time to put new wires on.

Thanks for the video but we can't hear you.

Did you fix the problem ? Same thing happened with me

This was informative and very helpful for the exact issue🎉. Appreciate you sir!

Blah blah blah, cut the fat. Do yourself better

*QUESTION: IF EXPANSION TANK IS GETTING FILLED --BEFORE FAILURE, CAN YOU REMOVE THE TANK, TURN IT UPSIDE DOWN, DRAIN THE WATER, REPRESSURIZE BLADDER TO CORRECT PRESSURE, THEN REINSTALL??*

*USE A NORMAL TIRE GAUGE ON BOTTOM OF EXPANSION TANK TO CHECK THE PRESSURE. SIMPLY PUSHING IN VALVE TO HEAR AIR TELLS YOU NOTHING. PLUSE IF YOU REPRESSURIZE YOU NEED TO KNOW HOW MUCH PRESSURE YOU PUMPED IN. USE THE TIRE GAUGE*

*ALSO, THE BLADDER IN THESE TANKS BREAK AND LEAK. IF YOU SEE RUST AROUND THE JOINT OF THE TANK, YOUR BLADDER AND TANK ARE LEAKING AND MOST LIKELY COMPLETELY FILLED WITH WATER* VERY HEAVY TO REMOVE, HOLD ON TIGHT WHEN UNSCREWING, 40 POUND DROP

*MAKE SURE YOU HAVE A STRANGER STRAP TO HOLD UP THE WEIGHT OF THE EXPANSION TANK. THEY GET VERY, VERY HEAVY. EXAMPLE, A GALLON OF WATER WEIGHS 8 POUNDS AND THE TANK HOLDS 4 GALLONS, PLUS WEIGHT OF THE TANK.* *ABOUT 40 POUNDS CAN BE HANGING ON THOSE PIPES!!*

Dam this guy is can’t stand still. You and actually see wheee talking about.

So, how long do these clamps last. I had one put on almost a year ago, and the sound it now coming back

Great information thank you! Had a hell of a time and Vise Grips idea was great!

My attention is drawn to those "brackets" in the area of the black colored wall board that provide rigid support for the piping. Are those brackets home-made or available otherwise?

And how to connect

Can you help me , I want to know, about right cell pin, left what is it.

Nicely done 👍

Hi Mr. Dave! Thank you for your very thoughtful and thorough explanation about the expansion tank on hot water heating system 🙂 Remember Dave, that God loves you and wants you to love Him too - with your whole heart! Thanks, again, Dave.

that device on main pipe next where half inch line connects to the right is an air Seperator for system so it would remove air in circulating water it should have an automatic vent on top to let the air out. you could get some air up in some upstairs pipe if you don't have automatic vents so you should check one of the highest radiators manual vents to see if any air comes out once in a while.

if your system has automatic vents the air that leaks from tank will just get bled from system as it collects at high points usually the best test is to see if pressure on the boiler gauge goes up a lot as boiler heats up from cold to full temperature it will go from what the autofill filled it to 12 or 15 psi and climb as boiler heats up till it goes over 30 and releases pressure out that side pipe on the pressure relief valve which should run down to within 6 inches of floor. sometimes your system pressure can be too high because the auto fill valve has dirt in it or is worn out and whole system will climb up steadily till it blows relief valve. you can put a tire pressure gauge on the air valve and see if you have around 12 to 15 psi and newest tanks have a water has gotten to the cap feature where it changes color when diaphragm ruptures. it would tell you in little instructions attached to valve when bought.

What air pressure should you re-inflate the bladder in the expansion tank to?

Model number for Replacement switch dp4t?

I also have an Aquasource and had the running water issue. I turned the fill valve 45 degrees counterclockwise to unlock the height of the fill valve. I adjusted the height of the fill valve two clicks down and turned it 45 degrees clockwise to lock it back into place. Problem solved. I wouldn't have thought of turning it if it were for this video, so thank you.

The green light is on because when the alarm is activated it initiates a fail safe relay that runs the pump as if the manual run switch is depressed. With the alarm light still on and the pump not running it means the motor itself or the contactor is bad.

I supose the govt decided we don't deserve a pilot light.

Great video. It addresses the EXACT problem that I just discovered in my Corolla Matrix. The repair shop wants me to put in an insurance claim, which will cost me AT LEAST the deductible. Not going to do that, when I can fix it with a little effort and a piece of hose. Thanks.

Opps, should of watched it all first!

Dave, maybe using a router to make that slot would be easier?

The replacement part in this video only lasted 2 years so I am trying another one from amazon. Repairwares Gas Range/Oven Igniter 316489400 316428500 IG94 AP3963540 316428501 5304462661 PS1528534 1197384 7316489400 IG9400 (Flat Style Ignitor) for $30. My suspicion is that all the aftermarket ignitors seem to look so similar that they are probably made in the same factory. So I am not expecting anything better on this one but I am taking a chance since I should get it the Tuesday before Thanksgiving while the searsdirect model will come the Tuesday after Thanksgiving.

Hi @mrdavetrouble, I know this video is 4 years old but we are considering getting one of these E/One systems. We were wondering if there was a sewer odor at all that came from the top of the lid where you have the pump. We'd have to put ours like right in the front of our house and we didn't want to smell odors anytime we went outside. Also, what is your overall opinion of the system, any major issues? Thanks!

your introduction way to fucking long ,, bye bye

This video was extremely helpful in removing the bad igniter since my oven was very similar to yours. I purchased a new igniter from Speedy Appliance Parts for $46.20, and it installed easily.

I really love how much people on RUclips over explain everything when fixing something. Just show how to fix it. They'll talk to you about their dead grandmother or whatever and not just get to the point. This video took forever.

This track is over 40 years old. Johnson 1700 series is way different now.

I did mine yesterday. What a terrible job. Did not remove the wheel. Removed 3 plastic fasteners... was somewhat difficult because they are full of dirt. Folded back the plastic wheel well cover and remove cap and bulb. Worst part of the job was not being able to see while installing the new bulb. That was difficult. Other than that a piece of cake. Crazy subaru engineers that designed this stupidity!!!

Does anyone have the heart to tell Dave to quit worrying about his window and address the mold, algae and moss growing on his roof about 3 ft. away?

Where can i get the drive belt , for my aiwa cx-nma845.

Thanks for the explanation

I came here to see how the nut was loosened. Thanks, thanks for nothing!

You are correct at 6:27. The tab must be in the 8 o'clock position to fit properly into the housing.

Drill a hole in 90

Look up the transit of Venus , it’s all bs

I saw it in that telescope but not this one..that’s weird.