Видео

I like that idea thanks

Don’t call it a .21 if it’s electric 👎🏼

Great video!! but I hope you didn't drink the coffee i think some red oil ended up in it. @ 10.10

I run FlySky, So many questions.. so what receiver were you using? Was the receiver antenna run straight up full length out of the radio box? What software version were you using? What voltage battery are you using for receiver? I have an NB4 with zero issues, definitely a different radio.. the new stuff is pretty solid reception wise.

The old copper top. Nice paint.

De qué es el tubo de cobre?

U have a picture of the collar screw? Minr keep sliding on those tube.0

did u have same video with no music ?

Thanks

Hey, I have a flex shaft in one of my electric rc boats and I was doing a speedrun and it for some reason just stopped dead in the water and I took it all apart and there seems to be nothing wrong with the shaft, I grease the shaft after every 2 times of use, can anyone help me?

Even bum down its looking very predictable. Cant wait to see it run with better set up

Your coffee got a bit oily ...but hey it makes stuff slide out better !!!!

captions call your engine sound music. 1st time I've seen them be correct.

Thank you very much for the information.

So cool

I’d like to build the same boat with the TFL Jet pump on a 8S set up. Any insight on a build like that?

At 10:15 you dropped a oil drop in your coffee

What prop and motor are you using?

Great video. I Just bought a 51" gas boat off ebay and I'm installing a clutch in place of the direct drive. Your video answered a lot questions

Fantastic running ✌️🔥💪

You have oil in your coffee hahaha

Km/h

Motor ?

Esc ?

Excuse me, does the skeg act as a keel

When are you going to do a video on the Red Baron ???

I don’t solder my cable ends but I do if I have a loose collet . Because it makes the cable end a bit thicker.. also I mark my drivedog by tightening the setscrew.

Thanks for the inspiration for building my zip kits classic thunder

For a flat spot try 3 or4 of the cheap Dremel cut-off wheels all new to make it. I tried using a drill press to put a countersink into the shaft but you need a good drill press otherwise it will move. I've had a lot of trouble with some flex cable shafts being oversized, usually those made overseas as they're metric Add more gap for longer boats such as Crackerboxes, hydro's or Jersey Skiffs where the engine is way forward.

Its very speed 😜

Well if your offended with the gospel gathering maybe you should go so you won't be so angry there disturbing your play time. Good video though

Very good ☺️

Did you manage to finish the Miss Budweiser boat as could only find up to the engine build. You were going to show the paintwork and video camera fitting

Correct me if I’m wrong but isn’t the turn fin supposed to be on the inside of the mounting bracket ??

Please upload the un-dubbed video

My experience is you need to silver solder the flexshaft where it goes into the collet because the part where even you mentionedthe rubber band tightening like action, the flexshaft tightens up and does get smaller and therefore the cooler doesn't hold it no more, lost my share of flexshaft, props before I started doing this.

shame about the horrible music overpowering the music of the brushless motor, we can listen to music anywhere, when we come to see riggers running we want to hear the revs and thats all.no hard feelings

what wheel is that for the dremel

I have been using the Flysky it4s with zero issues on my aeromarine conquest and zippkits crackerbox... love the radio

Nice run and I like that your using a Flysky radio👍

Thank you for your helpful video ! Do you use any Teflon Ring between the drivedog and the stinger ?

so nice!!!!!!!!!!!!!!!!!!!!!!!!!!!!1

Pretty nice looking boat, JJ! Really nice! 😃 Stay safe there with your family! 🖖😊

Hate when dudes reset GPS on cam. Even worse are the guys that cry if you don't reset on camera.

Nice green...looks like Krylon jungle green.. I'm building on myself...tjanks for the info... Is the hardware all zippkits or speedmaster

NICE A BOX 👍👍 I run all electric boats these days. But as the old saying goes different strokes for different folks.

L👀Kin G👀D 😎👍👍

I am your 100th subscriber,just found your old channel today.The videos are awesome,a lot of cool stuff ,specially the Boatstuff is very nice! Greets from germany V-one

Great video

I just found out about your new channel i found you lol nice boat she's a runner