Видео

one thing you left out or do not know to do to save time...if using the same type and brand of "guts" use the old to measure the length of the new.

Awful new foundation for old plumbing?

Why the banded coupler and not a slip coupling?

Good job

Lead & oakum while wearing an Apple Watch wild times

Thank you for a very informative video. This helped a lot.

A call to code enforcement is in order here..

I replaced my filter cartridge today and discovered a major leak. This video was perfect advice to tighten up the set screw which was loose as suspected. 🎉 Thank you ! You saved me money and also got the house water back on asap!

Just yank something, guaranteed a spark

This is good craftsmanship but a weird choice

WHOEVER WIRED THAT SHOULD BE ARRESTED, I AM A FORMER ELECTRICIAN, AND I HATE HOMEOWNERS DOING THERE OWN ELECTRICAL WORK.

Good luck my man 😮

yikes

Looks good

Glad you are doing good work

how much should a job like this cost $$?

Clean install.

Your customer is a squatter.

Nice tank and burner though lol

It seems like someone is attempting to burn this house down, my next question is, is this a meth house

Thats crazy

You could have saved like 20 mins if you reused the pump cap, suntec and the Becketts are the same size, not the new new Beckett A pumps tho.

Glad to see you’re back with videos!

I have the same issue going on right now and your video has assisted me greatly. I never pulled a jet pump double pipe assembly and your video gave me a lot of insight on what to expect. I was wondering though, the top fitting with those 2 o-rings...how does that hook up to the lines from the jet pump. Does it slide into a special deal and seals?

When was the last time you changed that filter there’s some sludge in that thing lol

Exelente

You never showed the cleaning.

Thank you for this instruction!

I used to use cement okum...

Be careful,there may be some asbestos floating around that old boiler.Treat all old boilers and such as having asbestos within,wear safety equipment and be careful. Goodluck.

I’m Going to try this have same issue won’t shut off and goes low pump in only 4 years old I know the end at pressure switches are clear OK but the housing is probably where my issues at.

my dude, wear gloves!!

Nice work on removal of old boiler

Nice job thanks for sharing

Thanks this was very helpful !!

I did this and now my pressure gauge won’t go over 3.

Please enlighten me as an apprentice, how did the hot lead not melt through the PVC? I see that it worked but how does that not melt through the plastic and make the PVC weak?

Good vid. I have an old bladderless tank. It only takes about 20 seconds for the tank to refill, so I'm thinking it needs a recharge.

Ok so you could try get those rubber clamps for one side being in pvc and the other side being for the over the cast iron bell part of the tee. You can still fit the pvc pipe inside the bell. But if cost wasn’t a problem you having the molten lead and okum you could just replace with cast iron again. I hate cast iron, i use pvc and i replace it all always i have the opportunity, i just rip it all off cast iron and galvanized rotten metal pipes and goes all pvc, just leave tee like this on video when is too intrusive requiring break and replace walls

Gosh ok i said some shit on your video of the pvc lead okum but man i loved this technique to bust it up the old cast iron, i hate cast iron pipes. Loved this for real i got to try it lol

What do you do when the plumber you call doesn't know how to prime your well?

Nice work

What kind of lipage was that black rubber piece ?

Unfortunately I have shallow bedrock above the frost line, so we can’t use a baker coupling on our well. I’ve got a guy coming next week to extend it with a welded coupling.

Nice job, buddy.I wish you live in new jersey to saint county area

I've done that plenty of times. All these fernco guys in the comments lack skills.

Thanks for this video. I watched this before I replacing the water valve and flapper at my house. This video helped me be successful.

Thank you. Excellent video

The guys incessant commenting is annoying.

How do you get the handle back off? I have an older one I’m trying to repair.