Видео

Thanks! Next one and last one is the riser 😅 Then will move to K2 Plus I hope

Thanks mate!

Yes! I had that spool on the shelf maybe for a year and used twice before noticing that 😅

Thanks ☺️

I read a lot of posts about this before doing it and have the same fear. I don't know is the cable managing on the K1C is the same as the K1. You can always disassemble the bottom of the printer to check it.

@ you were right, I took the bottom panel off and there is a zip tie 👌

Nice! Not in the K1! Good to know, will add a clarification on the description 🤗

@@Frikarte3DI had an idea to exhaust the warm air into a single spool container, I’m a newbie though, what’s your thoughts on that? Could be useful?

Umm, from the back fan to an "in-build" filament dryer, obviously mounted on the side? It's nice idea, but also have some doubts about how to regulate the temperature in the container for different types of filament or if it will extract enough temperature to be functional. The good ideas always needs to be tested 😅

Yes, I'm using my K1. I used Creality Print with the PETG settings suggested by LEOTE on his instructions of the CREALITY K1+K1C LID RISER V2 you can find here: www.printables.com/model/890518-creality-k1k1c-lid-riser-v2-50mm-height

Umm, I didn't notice a glare on mine for now. I want to print a riser and add more lighting. We will see after that 😅

You only need a little longer, I suggested M3x10mm because have them at home but I think M3x8 will be enough.

@Frikarte3D yeah, I've seen that. I've used M3x8 in every corner screw hole an M3x10 in the central hole, the inside fan one. Works like a charm, I've mounted them yesterday.

@MrSousuke87 Great!

Go for it! It's the best I did on this printer

Hey mate! On the entire video or when not talking? Thanks for telling it 🤗

@@Frikarte3D When the music is playing and there is no talking.

@abjoy-b1b Ok! Will take that in consideration for the next one ☺️

Hola! Sí 😊

En el Creality Print 4 reutilizé los Gcode que tenía en el Creality Slicer porque los que venían por defecto en el perfil de la impresora me daba un error al terminar la impresión. Si los necesitas te los puedo enviar.

@@Frikarte3D si puedes pasar el código estaría muy bien!! Muchas gracias estoy por hacer el cambio con la Sonic,

Envíame un mensaje por Instagram, Facebook, X,... y te lo paso

Eso me pasaba sin el Sonic Pad y el autoleveling. Cuando no tenía el Sonic Pad la tenía funcionando solo con leveling manual y me funcionaba bastante bién así. El Sonic Pad solucionaba el fallo del firmware original.

Hey @lleroy8929, thanks for reporting this! Mine is still working awesome as the first day and with very nice quality, what's the issue you had? Thanks!

Thanks! This version is only for K1, you have the K1 Max here: www.printables.com/model/896236-creality-k1-max-honeycomb-style-side-mounts-kit Will add also on the description 🤗

Thank you!

I have got a Space Pi Plus from Cuvacoins on Creality Cloud also! But I've lack of space at my office now 😅

@Frikarte3D They are great bits of kit and a real evolution from the heated element type.

Thaks for your support! 🤗

Hi! It depends on how long the LED strip is, the intensity of the light and the quality of the batteries. With the specifications of the batteries I have and the LED strip I use, at high light intensity it would be about 500 hours and with medium light intensity it could reach 1000 hours. The batteries can also be removed and plugged into the electricity.

Hi! I used regular PLA and no issues for now! Maybe your leds are too powerful, you can try PETG or ABS or other LEDs. I use those s.click.aliexpress.com/e/_EjvYPZK

@@Frikarte3D I've tried with 5V LEDs and PETG, instead of 12V LEDs and PLA. Now everything seems to be fine. It doesn't heat up. Thank you very much for guidance!

Yeah, it's a 3d printable coaster that needs to be released before New Year's Eve to let people print it 🤗

​@@Frikarte3Dit's now 2025

@zariffzahilan5805 Happy New Year! 🎉🎊

Still running flawlessly since I installed mine ☺️

A how to design this? Not yet, it's on my list but I have a lot of things to do and only 24 hours a day 😅 Hope soon

ruclips.net/video/10IDgu_E75I/видео.htmlsi=8vZ9jTfHjBZvaKod

@JulesChristoph Nice one! Thsnks for sharing! I made mine using SketchUp, maybe someday I can release a tutorial 🤗

You have the link in the description mvip.creality.com/en/goods/goodsDetail/1844

@@Frikarte3D Hi Merry christmas from Denmark .I found out i should login to creality / download there it was .Thankyou for you upload and answer .Merry Christmas

I didn't know that. That's great! Solving known issues on new version is a good practice. I'm working on a riser build because that "fix" makes the chain too height.

K1c still has a chain

@beardog420 Fix also works on K1C, need to check if the backplate is the same

It's available for my members on Thangs and Printables. Also on Cults and Creality Cloud, check my platforms here: linktr.ee/frikarte3d

Thanks! That's a very nice suggestion! I will add it to my TODO list! It was a custom order for a commission that needs to be in a limited place. Will keep you posted. Happy Printing 🤗

I also have an X2 and the detail of that is more than enough for my projects. Thanks for the feedback about my speaking pace, I generated the voice with text to speech, will try to use my own voice in the next one

Same here! Still using Mono. Siraya Tech resin at 40um. All the new features and resolution is tempting.

@ericboyle8296 The detail is great, for my prints I don't need that much normally, depends on what you gonna print

Thank you! It will be great if you can support it by giving it a like or downloading free here: www.printables.com/model/1070712-3dpi-2024-voronoi-trophy Thanks in advance 🤗

Sure I did give it a like​@@Frikarte3D

Thank you very much! 🙌

Its tolerances make it fall touching the X rod and dragging/sagging during printing

Not AI, it's a text to speech feature that exists from long ago before the AI. I use it because I'm looking for a way to make my voice sound better. You can check this one and hear my voice ruclips.net/video/_EqsxqF54AY/видео.html and will notice the poor quality of voice and accent 😅

If you use the raiser you cannot but you can only print the chain and solve the problem. I have another mod prepared to have the up higher and the enclosure again

The K1C have the same chain as the K1. So it must work, maybe the rear raiser is different, but you can try to fix without the raiser because the chain itself is very strong.

Just added into the description. Is this one: www.printables.com/model/621037-creality-k1-ptfe-guide I have a plan of showcasing all the printed mods when finish the assembly.

@ thanks for sharing :)

I didn't know that, if you can provide the link to the user who asked it will be perfect! I designed this from scratch, letter by letter inspired by one I saw on the Internet. Thanks 🤗

I believe it's keepmaking who did the original to this and has a very detailed video and files available. ruclips.net/video/iGtADvBl_Es/видео.html

@@jaredramkissoon2499 I designed mine using another software but yes, that's an awesome guide to create one 🤗

It's similar to the one of Disney, didn't remember the name

You can do it with this version s.click.aliexpress.com/e/_DEtDYsh 🤗

Thanks 🤗

Hello! I only make custom names as a comission, if you want it send me a message on Instagram and we can discuss the price.

Sorry, I'm working to fix this 🙂

@@Frikarte3D No need to fix it. It's your channel do what you want. Use eleven labs the quality is better. They also allow you to speak and upload audio and it changes your voice. Sounds natural. Never let anyone pressure you into doing something you don't want to do. If the guy hates AI voices he can go elsewhere.

@TPCDAZ I do what I can more that I want. Thanks for the tip, will check it! 🤗

Yes, this model only allows you to connect to the printer that way... I didn't find any other built-in option. I'm only using one AMS on them, have another printer with two without lights 😅

@@Frikarte3D So I can still have my one AMS working with the LED?

Yes, it is my setup right now. Also BIGTREETECH just released a new version without a switch that is controlled by the printer itself s.click.aliexpress.com/e/_DEtDYsh

@@ryan7288 On the mini yes. I have it. The strip was like 2 bucks on Ali "not so" Express. Worth all 200 pennies.

I have two connectors at the back of A1 and I don't use AMS right now

Yeah, for now I don't have plans on adding a second AMS without an official hub, but that's true

On the mini that's not true. My AMS works fine with the light.

@MikeD0162 I assume he refers about having two AMS connected

Normal do you mean not generated right? Working on a solution for this, I tried several times and I hate how my voice sounds speaking english 😅 Thanks for your feedback

@Frikarte3D yes not generated.lol

@coreytheMFstory Working on it

​@@Frikarte3DIf English isn't your first language, then couldn't you just speak in your native language and put English subtitles? If you already are typing them up for the AI voice, it would be about the same amount of work, but more naturally you. 🙂

Yes, this is my dilemma. I write all my content in English on social networks and on the platforms where I upload the designs and it was to give it consistency... But I need to deal with it

Awesome! I recommend you to use an extra layer of thin double sided tape because mine was a bit dry after one month in the bag

Hi! Hola! I didn't have fluent English speaking and my microphone sounded like crap. I maybe can do it in Spanish but will have the same issue with the mic. I tried this new text to voice here: ruclips.net/video/HQ-cSrguwto/видео.html What do you think? Thanks for spending time giving me feedback 🤗

Thanks for your comment and feedback! This printer is actually very nice. I doubt whether to use background music or not... This is at 25% volume, the one scheduled for next week is 15% I hope that will be better

That's a very general conclusion. I have two Anycubic resin printers and they worked always perfect for me. I also have a Kobra 3 Combo and it's working fine, could be better in some aspects but do the job.

i have other printers But this one is the worst

Ok

@@vidyaworld3d I actually really like their resin printers, and am still rocking a Photon M3. I don't have experience with their FDM printers. What about them in particular do you dislike?

Just asking the same, also this printer is pretty new so maybe he has a defective unit

Thank you for watching the video and spending your time writing this comment 🤗