- Видео 7
- Просмотров 155 814
causYOUcan DIY
Добавлен 28 окт 2016
RIDEN RD6006 Case - 3D Printed
This is a Case for RIDEN RD6006.
Has holes Side and back for connecting External Power Supply.
Lots of cooling vents.
CAD File Below.
www.thingiverse.com/thing:4816756
RD6006 Case 3D Printed
Has holes Side and back for connecting External Power Supply.
Lots of cooling vents.
CAD File Below.
www.thingiverse.com/thing:4816756
RD6006 Case 3D Printed
Просмотров: 1 371
Видео
Rotational to Linear Motion using Crank and Slider
Просмотров 74 тыс.5 лет назад
3d printed on Ender 5 0.2mm layer height with supports 5 walls and 4 top & bottom layers uses m3 & m4 bolts, 2x 8mm ball bearing's 37mm 100rpm geared DC motor 6mm shaft Stroke length 7cm STL FILES: www.thingiverse.com/thing:3600096
3d printed support wheel with adjustable axle length
Просмотров 5785 лет назад
A 3d printer wheel printed on ender 5 Diameter 91mm Width 10mm Bearing 626ZZ 6x19x6mm (6mm inner diameter) M4 Mounting holes, M3 screw for Tightening Axle Supports yes STL Files: www.thingiverse.com/thing:3600053
RC Tracked Vehicle Using Aluminium Profiles
Просмотров 4905 лет назад
I built a RC tank chassis using 2020 Aluminum profile, 3d printed wheel, 200 RPM geared motor and batteries from an old MacBook pro. This is my first outdoor trial with a 45 degree front wheel. Will need to try 35 degree to improve climbing capability. Built using 2020 Aluminum Profiles 12V 200 rpm geared Dc moter Macbook pro battery Detailed build video to follow.
Repair a Damaged Mac charging cable
Просмотров 1005 лет назад
In this video I show how to fix a macbook pro Cable. There are 2 individual wires. Inside one is positive and outer is negative. In my case the outer wire has completely broken away. I use loose copper wire and solder it connecting the split. I then heat glue the entire section
How to Cut Glass with a Dremel Diamond Wheel
Просмотров 64 тыс.5 лет назад
Cutting and Drilling glass with Dremel 4000. Attachments: 225-01 Flex-Shaft Attachment EZ402 EZ Lock Mandrel 545 Diamond Wheel 663DR 1/4" Glass Drilling Bit
Dremel Versatip 2000 cleaning and gas refilling
Просмотров 15 тыс.5 лет назад
In this video I show you how to clean a Butane soldering iron Dremel Versatip 2000 Butane soldering iron
Good idea for certain thing that i tend to invent
Ой, чьё-то очко будет промассировано 😉
Show me
Keya hame online mil sakta he project
Just found your channel and Subscribed. Very nice job
Well I suppose it’s about right that it made no sense and Helps zero since a woman made this video
Poteva anche evitare di fare questo video, non serve a nulla!!
Like the cooling system very clever..was wondering how to do that..great video..was also wondering what the long tube was for..very informative n thnx for making it so clear..
Has anyone put the parts together that the motor sits on top of? I am finding this very confusing! Also it looks like some parts aren't needed and some parts don't fit properly in place. I wish the inventor would have made the video more clear.
Thanks. Very helpful.
never cut and hold glass like this with barehands, if the glass breaks it will cut your hands and the dremel may also cut into your hands when the glass breaks, not safe! clever setup with the water bottom hole though
Thumbs up ....you read my mind. I already had a diamond wheel screwed in and ready to go. Ha. Mine is a smaller wheel, however. I just wanted to see approaches.
what parts do i have to edit if i wanted to change the stroke length? only the handel?
the rod that conected to the motor shaft.
Wrist protecters
No. That didn't fit too well. You forgot to include a locking mechanism. Press fitting is not adequate here.
speed?
Ingenious cooling...no need to spend additional money on a tool not used often
Variateur de vitesse ????
Love the poke in water bottle. GENIUS! Thank you for sharing that tip!
we all know what this mechanism is for ;)
how many bottles would you say you can cut with the diamond wheel before it wears out?
want to use for manual human breathing balloon please guide 9270260004 India maharashtra poona watap
Bunun aynisindan bulabilirmiyim
The edges are pretty rough after using that diamond wheel. Do you have a suggested attachment to smooth that out a bit?
I think one of the sharpening wheels might work for polishing the sharp edges. I think you want a low rpm for them
I dont know what the item number is but it could be an orange cone one set to low rpm
Yes... I was trying to think of a water cooling solution. Great idea.
Very interesting
Nice work
Pretty awesome! I just purchased a Dremel diamond cutting bit from Lowe's. I wasn't planning on cutting glass with it, but I love the fact that I can if needed in the future. I am experimenting with petrified wood, and stones, to create jewelry. Great info, thanks for the video! ~Joe ✌😎
you should be wearing carving gloves
Is the flex shaft necessary? What purpose does it serve? Couldn’t you just use the attachments directly to the dremel and get the same result? Great video! Thank you!
I am wondering this too!
I think it’s for ease of working with it. More control and not as heavy as the dremel. I went ahead and purchased it and I’m happy I did.
It is lighter easy to move around. Also as I use water don't want the tool near it.
Yea easier to manuever, lighter smaller to tighter spaces make for an easier use
Where can I procure these materials in Bangalore? Please guide me...
I used to buy from Aliexpress
What exactly do you need can help you out.
@@causyoucandiy5974 sir what is moter number ,any link
Water should be used for sure....glass dust will eventually lead to bad things. I know this from my work with stained glass. ALWAYS ALWAYS ALWAYS use water to contain glass particles. Dont trust a mask either...the dust will linger.
Ingenious cooling system - love it
best demonstration of using a dremel diamond blade to cut glass. I want to cut the handle off of a gallon jug. Hope it works as well for me as your project did for you.
Nice assembly
Very good, but how can get this material?
which part?
@@tushaarvishnu933 all parts
@@souravdhabal7465 The plastic I 3D printed. The cad files In descriptions. The screws from Ali express. Motor form robokits.in. It’s available on Amazon but more expensive.
@@souravdhabal7465 if you are in India. I can 3d print and send it to you
It also keeps the glass dust from getting in the air and then into your lungs. This is deadly if it gets in your lungs, even a tiny bit of the glass dust.
Is the water used to keep dust down or help lubricate it for wearing the blade down?
I know for cnc machining the tools would get so hot they would be destroyed without constantly being sprayed with coolant.
Robert Allen Neither I believe that it is to keep the glass cool enough from the heat of cutting that the glass doesn’t break.
The diamond cutting bit will last longer. Also helps with dust.
You didn't show how to clean the tip