Видео

i have just warm air coming everywhere and i just charge freon already... what can be ??

Thanks for the video. It contained the information I was looking for. When pulling out the heater core, i mistakenly removed the blend door actuator with the rod and wasn't sure how it supposed to align and go back in. Your video was clear on that so I really appreciate it.

That's exciting!

I despise plastic

Only problem for me is mine is blowing hot on driverside and cold on Passengerside I did change the actuators and still same issue

I have the same car, make and model and I changed out the water pump but it’s stalling to crank. Do you think I need a timing chain tensioner?

Pointless info unless the intake manifold must come off to remove the valve cover.

I have the same problem. But I bought the actuator and it did not come with that little piece that slips on the rod. What is that called? That part also has to be replaced because it turns the flap. I still need to find it. But I was able to flip the heat vent open by hand and wedged it open so I have heat now. So this still helped.

Wow! Thank you! I had the same problem. The crossbar on my trailer is outside the frame so it was easy to find where the bolt was missing. I fixed it🙂saved a bunch of $$$

What size bolt

Wow amazing.

This is six minutes and 40 seconds of babbling learn to get straight to the point you talk way too much sorry to be an ass but it’s just the truth

Sorry if I seemed excited but I finally found some jewelry at the beach. It wasn't a solid gold necklace but still it was pretty exciting. Man the beach was packed too so had to get out early in the morning to hunt. Had a blast. And the Garrett Apex worked great too. Very easy to discriminate targets. Also using the Garrett pinpointer helped big time too.

Awesome!!!💖🏴󠁧󠁢󠁥󠁮󠁧󠁿👋

Our slide out is a "rack and pin" style. It has a hydraulic ram that pushes and pulls it in and out. I had to drop the piece of metal on the bottom to access this and when I did...I found the bolt that goes in the shaft that drives the other gear had broken and dropped out. I had to measure the slide to get it set right...and put a new grade 3 bolt back in it. It's crucial that you don't use a grade 5 or 8 bolt...as this would mean that instead of the bolt breaking...it would probably mean something else would be damaged (gear, floor, anchor points, etc). If the bolt has broken...that is an indication that something is binding. So try to keep gears and rollers lubed and clean when possible. Maintenance may be a pain...but trying to repair damaged parts can be an even bigger pain and might be expensive too.

Thanks for sharing. I think you provided me the info I need. God bless☺☺

I am replacing the blower motor in my 2003 caravan and was wondering what position the blend door has to be in before I put it all back together. I also was wondering how the actuator motor turns on to move the blend door. Is it determined by temperature? I assumed that it went on and off from a switch on the dash board.

How did you get the rod out? ive opened mine and all i can see is the plastic fitting that attaches to the rod

When the hell will people learn to TURN YOUR FUCKING PHONE SIDEWAYS!!!

Thank You Sir

What one is for the drivers side.? There is 3 of them. Ours is blowing cold air on the drivers side and hot from the passenger side. Nice video it is helpful. I just need to figure out what one is for what.

Good job , thanks for info

Yep just viewed it. Not to bad, I like how you showed the rod. I was afraid to take it out when I did mine because I wasn't sure how easy it would be to put it back in. Watch out for posting on YT, it gets a little addictive if you like to teach and share your knowledge. The real pain in doing videos is the editing of a lot of footage. Keep my channel in mind I have a LOT of Caravan videos in a caravan playlist there. There's one that's helpful if you want to do your spark plugs, it teaches you how easy it is to remove the wiper assembly to gain easy access to the back of the motor. You can do the upper O2 sensor, valve cover gaskets, spark plugs etc. Well gotta go. Chat with you later Wayne. Best Wishes n Blessings. Keith

keith noneya...here is my video