Видео

Very thanks to You for this tutorial. Is there any tutorial for both blast and impact action of projectile to wall?

Hey where did you get the engineering data from for the fiber ? And the corecell??

How can I find failure criteria index for composite

how to open the ADPL command with ansys 2019 ? please

thanks a lot . Can you please tell me how to make the results into 3d ?

Hands down, this is the most comprehensive guide to ACP on RUclips. I have watched over 20 videos and this covered all the important aspects that most videos missed. Thank you so much, team.

Hi, What is meant by the negative values of stress in the stress plots, PLY wise?

ERROR! Number of nodes and elements exceeded for Academic Student version - nodes and elements both limited to 128000. 🥲💀

why load step 1 should be set with a very small ending TIME value? will it generate errors if the value is big ,like 10s

Thank you. It was really helpful. I am curious , why the third creep constant was set to 0 ? If i am not wrong C3 denotes Q ( Activation energy for creep) . How big would be the difference in results if i chose to include c3 ? TIA

Thank you for the very informative video, the question is if I have the experimental test data, how can I get the 9 constant of an orthotropic material of a woven CFRE?

Perfect!

how can i know totak thickness of my composite?? i want to make composition of kevlar fiber and other material want to compose these tow on each other last thickness of whole is 16cm kevlar and 4cm other

Thank you so much, can you explain me how to create a composite material of FMLs 5layers ( AL, epoxy, GFRP, epoxy and AL) please

thanks for the video

Thanks 😊

Hi, I have a small doubt, while meshing we are giving some thickness, does that thickness really matters? please address.

do more videos

First of all thank you...is it possible to create a stack up on 2D axisymmetric, assuming the strip of a cylinder??

do more videos

This is nonlinear buckling with geometric perturbations, different from post buckling. The latter would need the ARCLEN command.

Thanks a lot for the video. As far as I understood, the imperfections from the Linear Buckling Analysis ( LBA) is carried into further static analysis, which essentially is a non-linear buckling analysis right ? So, how can we extract the critical buckling load in the non-linear case for this example ( cylinder under external pressure) ? For a force load, I could plot force vs displacement curve. For a pressure load case I am unable to extract critical buckling pressure in a non-linear analysis. Please help!!

hi. introduction to creep pdf i need. can you send me pdf of this book?

Hey sir while downloading what do I put in" do you have a serial number that starts with 9020" I don't have any code or serial number

I tried this process but the results at static structural gives 0 inverse reverse factor

Great...

Excellent, the through thickness stress plotting was difficult to find. Thank you!

Hello how did you access the corecell a550 and t700 carbon fiber mechanical properties ı cant find it on websites very urgent

Hi, could you help me to understand one value? When you put the pressure value 9800 N/m^2 its because 9.81x1000 ? If it was dry sand i had to put 9.81x1553 (or the density of the material)? Thank you very much.

Nice

That was so good, keep going I have just a question I have a problem in setting analysis for phase change i wish you can drop your Gmail ?

Good

Good morning, Thank you for your sharing. It is very good tutorial 🙏

Hi I have a doubt, how could i communicate with you.

Many, many thanks. Is it possible to get the geometric file (Modeling file) so that we can practice at our end?

Nice and professional draw's method... Congratulation !!! In addendum: The next time you have to explain with words instead of music which is anti-learning for a beginner who follows your tutorials.

I'm looking to do this with polypropylene but couldn't find Constants. can you link any sources please.

how can i add functionally graded material ?

I followed your video and an error occurs when I go from solution to model. Error is "Update failed for the Solution component in Eigenvalue Buckling. Error updating cell solution in system Eigenvalue Buckling." I'd appreciate it if you could answer.

a very good lesson. It is suggested to add commentary rather than plying music in back ground. It will be more attractive for students. Students preferably watch those videos which are supported by commentary

Thank you very much....it was perfect. I have a question I did everything same as this video but i saw below error. "An error occurred inside the SOLVER module,The refrence units defined for the creep does not match." Why this problem happened?

Super good video. The only question I have is how did you come up with the enthalpy table?

Thank, how are you for obtain the Material Designer environment, because in the Student version of Ansys not are.. any page or method?

Comprehensive

I want to model the two steel plates and wrap the CFRP material around it. Need the ANSYS simulations. Can you do it? please drop your email below. I need to connect with you. Thank you !

Hi i wanted to make a composite of vinyl ester mixed with silica filler and glass fiber.How shld i proceed?

Sir it says couldn't connect to element orientation service and doesn't solve. Help please

How to join two different ply designed seperately as in one of the layer is a woven mat and the other is a rectangle as in this video.... How to join then together.... Please help

Really helpfull tutorial, thank you for the upload. Have you ever experienced an error while connecting the "Solution" of Buckling to the "Model" of the second Static Structural? For your exact Model it works as intended, but when I try to do the same with an other shell-model I just experience an Error message "Update failed for the Solution component in Copy of Eigenvalue Buckling. Error updating cell Solution in system Copy of Eigenvalue Buckling.", when I try to click update on the "Results" panel. Ihave no Idea why, everything is the same as in your video, but the model. I use a simple rectangular plane.

Sir the material designer is not available. Is there any way i can download it. It was made available in 19.2 version.