The Clay Cellar
The Clay Cellar
  • Видео 3
  • Просмотров 22 957
Kiln Controller Tutorial (Bentrup TC44) - www.claycellar.co.uk
Roger Watts from www.claycellar.co.uk giving a tutorial on how to use the Bentrup TC44 kiln controller.
The Clay Cellar is a family run business in South East England supplying pottery materials and equipment to the ceramics market.
Просмотров: 5 700

Видео

Kiln Controller Tutorial (Dealing With Error Messages) - www.claycellar.co.ukKiln Controller Tutorial (Dealing With Error Messages) - www.claycellar.co.uk
Kiln Controller Tutorial (Dealing With Error Messages) - www.claycellar.co.uk
Просмотров 1,2 тыс.10 лет назад
Roger Watts from www.claycellar.co.uk giving a tutorial on how to deal with error messages on a Bentrup kiln controller. The Clay Cellar is a family run business in South East England supplying pottery materials and equipment to the ceramics market.
Kiln Controller Tutorial (Bentrup TC66) - www.claycellar.co.ukKiln Controller Tutorial (Bentrup TC66) - www.claycellar.co.uk
Kiln Controller Tutorial (Bentrup TC66) - www.claycellar.co.uk
Просмотров 16 тыс.10 лет назад
Roger Watts from www.claycellar.co.uk giving a tutorial on how to use the Bentrup TC66 kiln controller. The Clay Cellar is a family run business in South East England supplying pottery materials and equipment to the ceramics market.

Комментарии

  • @katerinakankova7052
    @katerinakankova7052 Месяц назад

    This is the best instruction video for beginners with firing. Calm and clear. Thank you! Couldn't you make one for TC75? :)

  • @Jivanashakti
    @Jivanashakti 2 месяца назад

    Hello . I am writing to you for a personal reason regarding my single-phase electric ceramic oven (230V) Kittec classic Line CB 66 Double and about how to program the plateaus of cooking in the Thermocomputer TC66. I purchased this ceramic oven with the TC66 thermocompudor here in Holland where I currently live, and it turns out that the only manual and instructions I received is very basic and I currently need to do my first bisque firing and later the glazing one but I cannot properly program the plateau which is necessary to fire the pieces with the glazes and for the glazes to set in due time and appropriately. The manual I received does not mention at all how to program the plateaus in the firing curve that must be programmed in the TC66 thermocomputer and the truth is I need more information about this so as not to screw up and the ceramic is going to break inside me. in the oven or at the time of applying the glazes, do not exceed the temperature and come out damaged. Can you help me and may be also more coustomers with some other video tutorial? Thanks in advance ❤

  • @Optikification
    @Optikification 5 месяцев назад

    Very good video, my wife just got this controller and the shop programmed it but she needs to tweak it a bit and your calm and easy to follow instructions help her (who is Dutch) to understand.

  • @marijaenika7692
    @marijaenika7692 5 месяцев назад

    The best lesson, thank You!

  • @janverheul7053
    @janverheul7053 6 месяцев назад

    Very clear instructions

  • @nanouh8566
    @nanouh8566 Год назад

    thank you very much to translate in french !!! <3

  • @Barthoization
    @Barthoization Год назад

    I bought this controller for a kiln I bought ( without controller ) , Once it checks itself out ( 1:18 in your video ), It gets the E62 error, and then the fuse inside the controller breaks. There is nothing attached to the controller ( except power and temp sensor ). Error 62 is something about continuing fire after power failure. Since its a brand new controller, do you have any idea why the fuse keeps breaking ?

  • @davewood9639
    @davewood9639 Год назад

    Hi Roger, great video, we used ours, and this morning found an error code on the controller. E A-1? What should we check? The sensor?

  • @kitija1939
    @kitija1939 2 года назад

    Thank you! You explained that perfectly.

  • @jacquelinegraveline1003
    @jacquelinegraveline1003 3 года назад

    Traduction français

  • @willyanderskov9341
    @willyanderskov9341 3 года назад

    hvordan kan jeg få en dansk manual til YC 66

  • @sociotiago
    @sociotiago 3 года назад

    Very well done! Nice and clear. I love the way things are explained.

  • @boomtowncats8927
    @boomtowncats8927 4 года назад

    Thank you! 👍

  • @barrywyllie5383
    @barrywyllie5383 5 лет назад

    #-

  • @tubi2009
    @tubi2009 6 лет назад

    Very useful! Thx for this little tutorial.

  • @irisr8790
    @irisr8790 7 лет назад

    Fantastic video. So much better than the poor instructions sent with the kiln. Thank you very much.

  • @kuodukas
    @kuodukas 7 лет назад

    The best lesson, thank you. Very calming and understandable explanation :) Would be nice to see the same tutorial for TC88

    • @tonychandler9725
      @tonychandler9725 6 лет назад

      This tutorial is good for the TC88 as well. The difference is that the TC88 has a LCD display and more programs, otherwise the programming technnique is the same. Bookmark this page for brain fade which aged people such as myself suffer from time to time! Thanks Roger

  • @leslieryan603
    @leslieryan603 7 лет назад

    Thanks so much this was so informative and clear! I hope you are an educator!

  • @IsabelCintraTorres
    @IsabelCintraTorres 8 лет назад

    thank you

  • @bespokebuckles8089
    @bespokebuckles8089 9 лет назад

    Hey I've just completed a firing and kiln is on cooling phase, but judging by the cones it hasn't reached the internal temperature that I programmed - can I re programme it (whilst it's cooling) to a higher temperature as it is still quite hot and it would be more economical rather than to wait and start all over again? Cheers Sarah

  • @ahmedrashied6733
    @ahmedrashied6733 10 лет назад

    How much it saled?

  • @ahmedrashied6733
    @ahmedrashied6733 10 лет назад

    How much it saled?