- Видео 4
- Просмотров 36 612
Peter Kovács
Добавлен 2 апр 2020
Making oboe reeds
Oboe reed making - PART 4 - Making reed with profiler
Hello again :-)
Welcome to video no. 4 on reed making using an oboe profiler.
I use the Rns oboe profiler for 2 - 3 years and I can say that it is really a big help for oboists.
I use three templates MT, MAU and LORY .
Each template must be played with a different embouchure :-)
The reed is ready to play in about 3 to 5 minutes.
Of course, you have to play on it for a few days and then the reed is ready to go on stage :-)
Enjoy watching :-)
The cane is Moliniere (2009) 10,3 - 10,5 mm, 56-58/100mm, Hardness 10-14
Welcome to video no. 4 on reed making using an oboe profiler.
I use the Rns oboe profiler for 2 - 3 years and I can say that it is really a big help for oboists.
I use three templates MT, MAU and LORY .
Each template must be played with a different embouchure :-)
The reed is ready to play in about 3 to 5 minutes.
Of course, you have to play on it for a few days and then the reed is ready to go on stage :-)
Enjoy watching :-)
The cane is Moliniere (2009) 10,3 - 10,5 mm, 56-58/100mm, Hardness 10-14
Просмотров: 8 114
Видео
Oboe reed making - PART 3 - Hand scraping reed
Просмотров 12 тыс.4 года назад
Welcome to the third part of reedmaking - hand scraping reed :-) Here You can find my way of scraping. I don't use a dial indicator for scraping, I just try the reed and try to keep the scrape area symetrical. But if You want, You can of course use it. Enjoy watching :-) Audio : 1. Heinz Holliger - J.Reitz, Konzertstucks in F minor 2. Heinz Holliger - J.Reitz, Konzertstucks in F minor 3. Heinz ...
Oboe reed making - PART 2 - Shaping and tying
Просмотров 10 тыс.4 года назад
Hi again, welcome to the second part of my reed making. In this section I would like to show you a shaping and tying an oboe reed, which is very important part of reedmaking and perhaps more important than the final scraping. If you do this incorrectly, you will never have a good reed :-) Enjoy watching
Oboe reed making - PART 1- Tube cane selection and gouging
Просмотров 7 тыс.4 года назад
Hello, I would like to show You my way of making oboe reeds. I play the europe scraping reeds, so I show you this model of making. I tried to make this video useable for all level of reedmakers, so You find here making reeds with, but also without all machine for reedmaking which I now use. Off course, some of them You must have 🙂 In this first part You can see tube cane selection, splitting, g...
Hello Peter. I have a question. ¿What shape of cane and hardness do you use in this video? And which of these three templates do you recommend to play Bach? Thanks a lot
Hello, I used Borgue shaper form, and hardness about 10-11, from these three I think MT ,depend on which "Bach" 😇😇 now I am making usually with Kge machine 🙂 But shaper form still same 🙂
Very good video,I am making reed eveyday,is so tired.
Muito bom!
What is the name of oboe solo in background?
Schumann - Adagio und Allegro, originally a horn piece
that's great! so much patience ! all the videos of this channel are very interesting and useful, thank you for your work. it's so good that now I have a profiling machine for this, my reeds did not play well with hand sharpening.
Very interesting remarks and suggestions. Thank you all ! I play a Marigaux 901 and wish to order a profiling machine Reeds and Stuff. Which template would you advise me ? MAU ? Lory? or ??? Thank you for your answers ! Michel. France.
Very good is vídeo and top
Hello. I'm from Brazil and I appreciate your vídeo a Lot. I have an hautboy from Patricola modelo S4.
Yes, I echo the sentiments on the visible technical detail that you demonstrate in the reed profiling process and also the additional refinements made to ‘fine tune’ the whittling process. However, the PLAYING: I have to say, I am enamoured by your playing. I’ve listened to many fine oboists and there are so many more to listen to but I have to say that I enjoy your playing. It resonates with what I practice to aspire too in terms of control, tone and articulation. Please state whether there are videos of you playing on line and if not WHY not!! I, for one, would love to hear more of your expression on the oboe and I’m sure, in all humility, that there would be others that would second this request. Please!!
Thank You 😊😊
Great video Peter. Thanks for posting.
Has been so helpful to me,no doubt😀 thanks~
I appreciate the differential demo. I was wondering what oboe are you playing and what make and length of staple are you using. Thank you for the video.
This was really informative thanks. I'm considering buying one of these machines and was trying to decide which templates to go for. Im thinking of getting a Lory for the lovely rich and mellow sound, and the MAU for the brighter and more flexible sound for solo/concerto work. :-)
Your video will be a great help to me. thank you. I have a question. How long has the cane been soaked in water before it is machined? Also, what is the thickness of the tip? I'm happy to know them.
Hello, in watter about 10 minutes, and the tip thickness is about 10/100mm
Exactly what I've been looking for: no fluff, no fillers, just straight on with the nitty gritty, Thank you so much.
Hi sir.... May I know d title of your background music... Its so beautiful piece.
I've just subscribed. May I please ask what oboe you are using? Have you used an AK Loreé, and would your scrape be different because of the brand of oboes available? Thank you for your videos. I have at least several of Holligers LP releases, of around 190+.
Flexibility tester... never seen that before, interesting but would add to the budget as well. But nice demo.
I’d never have a parrot as an oboist reed maker. No profiler for me. I met Robert Gilbert in 1972 and been making reeds ever since then, and still. I wonder what gouge you use. Thanks for sharing. By the way, I never did have a recording of what your soundtrack is here. It sounds like an Italian Concerto. I have 10,000 records and I don’t think I have a copy of that :-)
I do final dusting too, when the reed rests over night and still dry.Voila!
Goosens?
Ya no way in hell I’m gonna try this for a long time
Wow, amazing videos! Thank you very much for the insights you gave us :-) I guess you had to adjust the reeds after shaping them with the profiler? There were only few reeds, that worked good for me when playing it instantly after shaping. Or is it only a matter of profiler adjustment?
After profiling I just play on it, and if its hard, I put it back on the machine. Maybe little bit adjustment of tip, if its too thick. And check the sides if are the same thickness.
Hi Peter, How many mm down the mandrel do you push the shaped cane?
Hello, its about 21mm
I think like you. I find the best is MT. Could you give me some measurements from your reed? Length scrape 10,5. But tip? how do you put your MT in relation between the the ruler on the machine. Do you have email ? Thx
I ussually set the lenght of the tip one mark in template tob the right 😉
Fantastic instructional video! Just amazing. Thank you.
Great video, thanks a lot!! Very informative especially about the templates, from which I think it's difficult to find information how they actually differ from each other. I would like to ask about the clamp mechanism, how tight do you use it with MAU? :) I wasn't hundred percent sure based on the video, sorry :D
These are excellent Videos Peter!! Thanks for posting. Greetings from Copenhagen.
Thank You 😉😊
wow didn't know those existed, nice
Thank you very much indeed for making this video!!
Thank You 😉
Thank you for your video Peter. One question. What is the measure of the mark in the mandrel?
Hello 😉 I marked on the mandrel that point, where I put the end of the shaped cane for tighten the wire, due the correct position and fitting on staple which I use. I also used to make a mark on shape , where the wire will be, but now I do it by eye 😉
@@peterkovacs1397 thank you for your answer!
Fantastico
I use the Reeds n Stuff gouger as well. What bed and blade size do you use?
Hello, my gouger has 10,75 bed, and I used a 11,41 blade and now 11,70, which makes a little bit thinner sides.
Interesting, thx. Just wondering if you tried also Fab2 wich was recomended together with Lory for me
Hello, I have also Fab2, but for me is not the number one 😉 You can try it if is good for You. I will offer it for sell 😉
Great video, thank you. I have the Lory template too, but my reeds never work like that straight from the machine, even when the tip is scraped .10mm - I have to scrape so much more to get any vibrations. Any idea why?
Thanks 😉 I dont know exactly why it is 🤔 There can be more aspects why is it for example , the blunt blade, I had similar problem, but after resharpening the blade, it works fine 😉 Maybe to hard cane, if I have a realy hard cane, which is so hard in flexibility test already, the reed after profiling is hard to play, I let it dry, then again a little bit playing on it, and after that, I put it on the machine again, with same setting and ussualy came some cane of from it and is better then 😉 Other thing, You should try to not tight clamping it, so more cane is remove from back. The Lory has a little bit thicker back, so maybe it help 🙂
The cane could be hard, but not less than 10 on the hardness tester. I think the blade could be a bit old - I will try my spare! I really liked your videos - so good to see tips for Euro style reeds. There’s so much about American reeds but much less for us!👍🏼👍🏼👍🏼
I use from 10-13,14 hardness, but I also chceck the flexibility. The new, or resharpered blade can make miracle 😉 Yes, You are right, there is not many videos of Eu stylev🤔
Truly outstanding video!! Now that you've demonstrated the use of the RnS profiler, I think I'll have to get one too :) I would imagine the "MAU" letters probably stand for "Maurice Bourgue" of Paris. Keep up the fantastic work, Peter! You're a wonderful oboist and teacher.
Thank You 😉 Its a big help for oboe reed making. But also You need a good cane, right shape , instrument 😊 and then is oboe life easier with profiler 😉🙂
I'm currently switching to European style reeds, I've been playing on them for a few months now. I'm considering buying this profiler but I have no idea what template to buy. Do you have a recommendation? I tend to like British Modern French style reeds that are a little brighter but more free blowing. I really liked the MAU that you used in this video in fact.
Hello, It is realy hard to say 🤔 I had to try some of them to find which is for me the best. Mau is very fine for me, its easier than MT and Lory. I think, Mau can work, there is also an ANA template, which I tried and works for me, also easier and nice playing. ( I tried Fab2 , J, Albi too, but these are not for me 😉 )
Sounds like you might Like the J or ANA which I feel is darker than the MAU.
@@peterkovacs1397 Thank you for your help!
@@veggiemusician Ill have to check both of those out, thanks!
Hello 🙂 For me is still the best MT, I also sometimes play on MAU too, but usually I play on MT 😉 I have changed my instrument to M2 Marigaux few mounth ago, and I have to change my shaper form for little bit narower.
Hi! Can I ask you what kind of knife do you use for reed making ? From which brand ?
Hello 😉 I use for scraping knife from Chiarugi, I bought it long time ago,but I think is still avialible 🙂 I have another one, also from Chiarugi, but I prefer this one 😉
I think is some of them 😉 www.oboe-shop.de/en/reed-making-tools-52/knives-58/
Thank you! :)
What do you think which cane has the most dark sound ? And how depend thick of cane on reed.
Hello, is hard to say it, there is lot of canes with dark sound, also You can make it with Your style of scraping. Now I use a cane from Turkey, which is hard cane, has nice sound. I use Lavoro and Rigotti also and they has nice sound too. I use thickness between 56-58/100mm For me is less so soft and more than 58,59 is hard, If You use harder cane. It depend on hardness of Your cane.
@@peterkovacs1397 thank you!
Hello! I have a question, when you use the precision scale, how would you translate the results to the hardness tester? I mean, if you get 20 on the precision scale, how much would that approximately be on the hardness tester? Thank you very much!!
Hello 😉 It depends on each cane You have, You get results maybe between 0,17 to 0,30 and You can choose which is good for You by trying it, and You get result that for You with Your cane is good 0,22, ( its a example ) I did the compare now for You, and with my cane is 0,225 on scale the 9 on hardness tester and 0,200 is 13 But as I said, it depend on the cane. So , I hope it will help You 😊
@@peterkovacs1397 thank you very much! Yes, this actually helps a lot! Greetings from Budapest! 😊😊😊
Super cool... what’s the sum total of the price of the equipments you use? Guilotine, gauger, splitter, knife, etc? Must be very costly to have them all...
Thank You 😉 I dont know the total price, I bought it separately, from year to year. I was making my reeds lot of year by hand, ( maybe 15 years ) without machines. I had only hand shaper, mandrel and knife 🙂 But, its a big help for proffesional life 😊
希望以后会有更多的关于双簧管之类的视频，各个方面都可以去向你学习！
Thanks :-)
我是中国人，我在学习双簧管。哨片一直很困扰我，观看过后你的视频，让我有了更多哨片制作的启发。非常好，感谢你的视频！！！！！！
Thank You !
Is this guy British I assume
Well, we can say you are not wasting any thread like others by fixing it to the window. :)
😁😁
I prefer the MAU reed you demonstrated. Excellent video! Have you tried the new Marigaux 1 Superleggera staples? They are FANTASTIC!
Thank You 😉 Now I use Mau at my new M2, it seems be better than MT on this oboe.
Outstanding video! I'll be looking forward to more. Now I'm going to straight to the next video! Many thanks.
Thank You
This is most interesting! I don't play the oboe but have been reading Laila Storch's biography of Marcel Tabuteau. There is a lot of mention of canes, reeds, gouging etc that I had absolutely no idea about. The oboist has a lot of extra work apart from practising the instrument..... which has the most beautiful sound. Hats off to oboists!
Excellent video! Very thorough, step-by-step explanation. For all the very fine scraping work, I've found the Reed Geek's "Double Geek" to be an absolutely essential tool!
Thank You 😉
from where we can get reed making machine?
I have my machine from RnS. www.reedsnstuff.com/en/Oboe/Reed-Making-Machines/Profiling-Machine/