Видео

What size nuts and bolts did you use ? Mine came with none

If you put a board at the bottom of the ramp you can get most low cars on it

Ty

I've had mine for a few years, using them to not only change oil but transmission fluid, apply anti-rust spray, and general inspection of what's going on underneath. They seem very rugged. There's a youtube video of someone crushing car ramps with a hydraulic press, including the Rhino Ramps. They withstood far above the rated capacity.

next sell gimmick for the people 20k lbs ramp for 100 you know you will buy it for safety. But all serious 12k is fine 16k for f250 trucks and above

After placing the ramps in front of the tires , I stepback and look down the side of the vehicle while eyeing the ramp at the same time to make sure it is lined up parallel. Doing this will ensure that as the wheels ascend up the ramp it will not drive off the sides, if there is any misalignment.

I use it on dodge 2007 1500 hemi 300 plus thousand miles going strong.

MGW is fantastic… F the review go straight to GREAT!!

MGW

Bro i was getting ready to take out the filter bow. 💪💪💪💪👍

Don’t add Lucas to transmission!!! It almost killed transmission in my Hyundai Elantra. But I’m sure it is good for engine.

You don’t need to torque to spec??

Dass Wossop.

I've seen these plastic ramps collapse. I would never use them.

Thank you for this video..my mechanic highly recommended this product & seeing how you went from skeptical to a believer gives me faith when I try it for my car!

Thank you very much for install video. I bought 04 Mustang GT with same Hurst shifter. Found it was getting loose at 2 bolts that hold shifter arm on. I don’t have the gasket on mine so going to use little blue Loctite on bolts.

Hello, "ChrisRodProductions" I was analyzing your channel and saw that in your channel have some problem, That's why your channel is not much growing and not getting much engagement, If you can solve these problems, Your channel will grow like a storm. If you tell I can tell these problems. Where can I tell? Here or ig or where?

Great video 👍

already have one!!

Ya I’m just going buy car no problem 😅

You’re entitled. People who work at auto parts stores don’t make enough to live. You should know better and if you’re worried about incorrect parts you can give them the entire vin. It’s your own fault you got the wrong part.

Here’s what I do. I go online, look up the part, call the store to grab the part off the shelf(just to make sure it’s really there) place the order online with the online discounts and go pick it up. No wait time since the part was already pulled. And make sure you get the associates name and repeat it back to him or her. So that they dont lie to you and say yes the parts there when they never looked. Lol

Sounds like a rod knocking lol . No oil stabilizer will fix that issue only a rebuild job

Fun little fact, for certain years the Ford 3.8l v6 and Ford 302 OHV (5.0L) did share the same alternator...also the same water pump as well.

I wish people would do what you are asking as it would make grabbing the right part faster

I work for an AutoZone and it seems in my area people hate it when I ask the questions that i have to put into help fid the right part. Our personal favorite is I need such and such part for a Chevy 350 we ask the year, they answer it doesn't matter there all the same. they should ask year make model look alternator then it brings up the engine if there is more than one size for that model year. Sometimes I'll have to go to a year earlier or later as they will be off because the moth i was made in so I can find the right part. Sometime the parts are boxed wrong.

You could’ve separated the filler neck from the housing and just pull the filler neck out without having to drop the tank. That’s how I did mine

Dude, I’m truly sorry about what happened at the parts store. The crap happens to me all the time. The people that work at those places don’t even seem to care that they have a job. I do have a question. I saw your video about the ex pipe I was just wondering that when you took out your catalytic converters, did it throw any codes or did you get a check engine light or anything like that?

I'm having a lot of issues getting parts from AutoZone and advance (for my new edge mustang gt). I can't figure out if it's because mustangs are so popular or something else. BTW a 105 amp alternator for my car from O'Reilly's was over 300$.🫤🧑‍🔧🛒

On the second pair, tossed the first ones after two uses idk how they didn't completely collapse. They always buckle near the front with my 2015 Ram 1500 BigHorn

I like it

So will the 9007/HB5 version work I found on Amazon

RICOS PERFORMANCE PARTS IS NO LONGER ACTIVE and Im currently looking for a new H Pipe set up. Be on the lookout for the new set up down below or in the description. LETS GET IT!!! HPIPE: LOADING...

You could have flashed a picture of trump if you got no results

But whats better the high mileage or the normal version?

🤣🤣🤣 good vid bro

Just picked up 2 sets on EBay $50 per pair, I’m doing a center drive shaft bearing and want plenty of clearance to work, I will be using Jack Stands for safety.

"what a goof" lmao

It does look like, you’re over the maxi width of the tire for these ramps (they say max 8".) How wide is the tire?

I’m going to need a new hoodie with new branding… Really enjoying the beautiful Venom hoodie you sent me!! 😂😂😂

Bro was not going deep down there fr 😂😂😂 hella reaching

👍

Had me cracking up bro lol good looks on the vid bout to go change my shortys car oil 🫡👏🏽🔥❤️

idk why I love that the 2v and 4v sound so different.

I got this this a couple weeks ago the only problem I have with it I'm 80 years old and all my muscles have pretty much gone South so it seemed a little heavy for me I'm keeping it but I went back to Lowe's and bought the smaller one and it does just as good a job on what I use for and I feel more comfortable with the lighter weight one

Let’s goooo

Gopro videos! ✅

램프가 저렴한 만큼 당신의 생명도 저렴해질 수 있습니다.

Here's to a great next 4 years! At least the fuel costs for my Cobra will be much better!

Hello. I have a 2009 BMW X5, 140k miles with loud noice in the engine. I put the lucas and the noice is gone, I am very surprised that it worked that well. However I have been seeing videos and some suggest that, it's not good to use it in cold wether, others that it will damage some components etc. Do you have any more info regarding LUCAS. Thank you. JC