Видео

Ran into this with my 3 filter unit. Ramming the filters into the tops before screwing them in has restored service for now. Thank you!

i got the SD code (suds) any fix on that? tried the rinse/drain/spin to get them out but still an issue, could my filter be clogged?

Thanks this fixed it for me too. Had to push the filter into place

Great Job on this video, My model is MVWB300WQ2, hope it works the same way. I will give it a try.

Same experience with LLOYD Havells .75 tons unit. I have now 5 units installed at my home. Saving over 50% in energy bills. I sent the video to LLOYD with same loud noise. Big thanks to LLOYD customer service. They sent a new complete outdoor unit. Problem fixed. It was a bad compressor. Not worth replacing just the compressor.

Mine sounds like this and when I sent a video to my Heating & Air company, they told me they didn’t think anything sounded wrong with it🤨

Hi when you first installed how was humming noise?Did it steadily get worse as time went by or did it just one day you noticed a louder noise?

🟢🟢 🔵🔵 🤎 🤎 🩵🩵🩵🩵🩵

Thank you for your video! I struggled to get a flow going even after re-inserting the filters multiple times. It seems like turning the supply valve on slowly, then the filter valve on slowly, letting it run a while, then opening both valves up fully really did the trick. I've gone through multiple filters with this system with no issues until the time before last. Maybe as one person responded, the new filters are somewhat shorter than they were engineered to be. In that case a washer placed under the filter might work. I'll keep an eye on it. Thanks again!!

Thanks, but just to let you know on my model, I have read that there has been a failure regarding a filter defect. The filters are being reported to be shorter, causing them to be pushed down under pressure. Thus causing what you are experiencing. I have replaced mine 3 times and yesterday I started experiencing the same problem you are seeing. I have read that a fix is to put a rubber washer under the filter. The factory should replace your filter, they know there is a problem. Call em up! I have some rubber O-rings, think I will give it a try!

wow thank you so much I was struggling with this issue for hours today and your advice helped me fix the issue quickly. THANK YOU THANK YOU THANK YOU 🙏

Well, damnit. From the video and comments, my 2-year old Pioneer is dying. Are these Midea-made units just that crappy or did I screw up the install and not realize it?

blah lah lah lah get to the point....too much talk

Ready fixed my washers thank

You the best bro

Your video was very helpful. The only one on RUclips to address my issue for the same type of washer. If you replaced the suspension (also did that), and the bearings including replacement spindle (possibly my next step), did you ever managed to find out what the issue with your washer was? Or are continuing to manually play with the spin cycle every time? Thank you.

would someone could help me please, mine dont work on cold cycle mode its always use hot water

Am getting an OL code what is the that for ? but same thing it leaves the clothes wet, so go into diagnostics and do the spin and drain like you showed, but new loads keeps stopping at OL. Any susggestions

Thank you for the very informative video. I have been struggling with the ul (unbalance mode) for quite a while. And I don’t have the means to purchase a new washer. Or even hire a repair person. You’ve saved me.

Your video is the only one that showed how to test the drain and spin. Thank you.

Replaced the rods on my Samsung with a set of $45 rods and still had the problem until I bought a tube of Nyogel 767a dampening grease and smeared a generous coating of the grease on the rods where the bearing rides. Works great. The replacement rods don't have enough or the right type of grease on them

The washer looks like Melissa

We have BRAVOS XL that keeps having UL code show on spin cycle and still shows after trying to rebalance clothing. We have never had any work done purchased new about 8-10 yrs ago. My husband is NOT handy is ready to purchase new washer. Any suggestions I can try? What is usually cost to have technician come over to fix unit?

It actually worked!! Thank you so much!

Helps me a lot

Bro. What the heck happened with this problem. I have the same issue. Went trough the same steps. Still jumps around during the spin mode.

Mine goes good up to the last ten minutes 🥴

great video helped me figure my pioneer out.

went to use my 48volt SJ blower for the 4rd time this year and now won't start?!!!

How to change out the bearings on this washer

What is oL error

very helpful, thank you

You could have a bad suspension which are easy to replace.

Thanks so much! You saved my headache! I have same washer like yours.

I had this problem with mine and the way Got my washer to stop working. Is level my washer by fixing the problem with the hobble Legs on bottom. The only way I got it to stay level was taking the legs out and adding a locking nut to the leg and when putting the legs back in is level the washer with the level going across the top of tub not lid once level i used lock nut to tighten against the washer frame. also laid sum rubber matts on bottom of legs to help the shaking on floor. The legs on washer are the worst thing about the washer.

Have same problem with a copper and hunter system

Thank you soooo much! This was so very helpful! I have the same washer and same problems

Ty so much.

Bearings in that particular washer is trash!!! I've been through 2 washers in 10 years!!

My has dL problem, can you help? What’s the problem you know? I turned on press wash, after water spray for 5 sec then DL error went on.

thank goodness I found this video. It help me found a way to spin dry our clothes. Our Maytag Bravo XL consistently failed with 14 minutes before completion (I believe right before the spinning occur, and the code is uL). I find this code to be generic and I'm still unable to pinpoint the root cause. I had a repairman came out and replaced an official Maytag suspension rod and that didn't help.

Eww why does it sound like that

Replace the suspension rods

Trying it now. Fingers crossed (2:53pm, Saturday July 29) UPDATE 2:54pm, same day): IT WORKED!!! THANK YOU!!! Fair warning: based on other videos, it’ll probably have to be tightened again, but this worked for the time being.

I am getting a control board for mine. I will let you know what happens

Hey does anyone know how to do a quick calibration on this washer? Sometimes it workes fine ... our days im plugging & unplugging

I was getting an LD error code on my washer. I took out the drum, removed a hand towel from the tub and cleaned out all the hoses, checked the pumps for obstructions, and while at it, replaced the bearings and shaft since they were rusty. I'm still getting an LD error and when running diagnostics, I got an F32 error. Do you have any idea what may be going on? The washer is not draining and making a gurgling sound.

Sometimes socks can throw them off. in the outer tub, sometimes socks go over the rim and stay on the sides, making weight uneven.

Wow thank you so much for this video!! I was almost going to cry because I thought I was going to need a new washer and I can not afford it at the moment. Thank you I did this and it worked !!! You are a life saver!! 😅😅😊

Just saved us from the horrible laundry mat!!!! Ty ty ty