Видео

That's why I would take one out at a time that way you don't have to mark anything, one plug at a time one wire at a time.

If you're car is misfiring it's the coil pack or packs and if your carbis older the distributor you can put mew wires and plugs in and it will probably run for a few days or more then it will start misfiring again if you beat on your car it could be internal or vacuum leak but for most normal drivers it's the coil pack going bad

The video was helpful 💯... but those swaybar links were shot and needed to be changed at the same time.

50ohm wires are for msd boxes use the higher phm wires for your GM truck. Usualy use Delco...tried a set of Napa premium (Belden) wires they are pretty nice dont come apart or cost much and grease wont stick to them.

Glad I found this. I am using a 2" header. I have switched to the Accel wires with ceramic boots hoping for more durability and heat resistance as well as a high level of RFI/EMI suppression. I was a little concerned that they would have too much resistance but from your experience that does not appear to be the case. Power levels of our engines are very similar. Thanks!!

I need to change mine so bad ,thanks for this video!

How fast

Any idea of the WFMC2201UC/13 washing machine? Mine just slowly spins sometimes, leaving me with a soaked load at the end of the cycle. Scratching my head here.

What is the part under the coil pack that the radiator hose connects to?

Stock transmission?

Can't see what you're doing coz your hands are in the way.

It would have been helpful if you had shown each ratchet/extension combo for each plug. Dielectric grease on the connections and anti-seize on the plug threads? Overall really good video-others show removing the cowl and wiper assembly to get at the plugs! You have made a dreaded project a hell of a lot easier! Thanks.

me out , I changed the spark plugs and wires on my 01 Carvana and after doing that my van has a ruff vibration at ideal or coming to a stop on red. I got a mechanic to clean out the threading where the spark plugs go and it keeps doing it maybe it’s the coils ? I also need an oxygen sensor maybe that will do the trick? If anyone has been in this situation help me out thanks !

Great help. Video hint though. One need not show the entirety of removing each nut/bolt/screw etc. just which one, which tool and how. Thanx for the help. Diving under next weekend.

you need to remove the front bolt all the way. Front horizontal First off, and rear vertical bolt (round part of control arm) First on. you're lucky you didn't break the front bolt lol.😉

Hows the van doing so far on these struts? Still holding up?

How often you use machine?(I do brushes every 8-9 years but light use machine (60 -70 or so runs a year)

What's the gap on the sparkplug?

great numbers. Your build is similar to mine.

2,4,6 3,1,5 you say along the back .. But then you take all the wires off the back all at once did you notice that and you didn't put them back in the correct order watch your video again ...... and you pulled number two plug wire off and the boot the copper boot was left on the coil pack and you're using Snap-on tools ... you are A PROFESSIONAL in the field of amateurs I don't even have Snap-on tools .... It Startup huh those wires are bad if it was your car would you not have changed that out and cleaned up your woman's van for her it's a soccer moms van 😂😂😂 .... ... E-3 plugs ....

I can't figure out why number 6 is not firing

Appreciate u brotha! Don’t give a damn how old this video is 💪💯

Great video for a weekend mechanic like myself, who only has basic tools.

Did they hold up better then MSD?

What is the length of your wires?

Do you have instagram This build is 🔥

So how did the Accell plug wires work out? Have you noticed any difference in performance from the MSD wires you changed from? Would you recommend Accell or MSD at this point?

Thanks! Looks fairly straight forward :)

Hello, where is your shop located would love to bring my 2007 gmc Yukon Denali Xl to get tuned.

Would you happen to know where the direct ignition coils are on this vehicle

Thanks for showing me where everything is at. Now I can see how much room there is to work with on the back.

Thanks for showing this. I've watched a few of these vids for this motor tuneup, and most guys doing it wonder why the plug wires/coilpack is numbered so randomly, when in fact, they are numbered according to the firing order from the crankshaft - there actually is a reason they're not just sequentially numbered 1-2-3-4-5-6.

Has anybody taken off the cowl screen and wiper motor to get better access?

I have to change my EGR valve, so, having the EGR pipe off should make it a little easier.

the ignition coil is most likely numbered that way because that is the firing order of the cylinders

No dielectric grease on the boots? No blowing out the sand/grit before removing the old plugs?

How much money do you save doing this job yourself.

The 2015 has the transmission closer. The bolt does not come out

6x13.5x35mm brushes are the unobtanium i need.

Good thanks

Sway bar link easier to take of with a 18mm wrench and a T40 on a ratchet.

I always use PB Blaster and a torch.

Gracias fue de mucha ayuda tu video

Where is your power steering reservoir? On my 2002 T&C and in other videos it is mounted right above the coil pack. I'm assuming the answer is not "manual steering".

Very nice! I enjoyed that, 🔨🤗🔧

How are those control arms holding up after a year?

Did this same job on my 08 town and country with 118k. The hardest part was braking the nuckle bolts really tight. Helps to have an impact gun.

🔥

🔥

So does this vehicle not have individual coil packs on each spark plug?