- Видео 8
- Просмотров 296 410
Richard S
Добавлен 4 мар 2013
Видео
Panasonic Microwave The Genius 1250w doesn't turn on. (I fix it)
Просмотров 6 тыс.4 года назад
This microwave didn't turn on or display any power. Changing the fuse with a CES6 N1 fuse (20amp 250V) did the job. Before you disassemble the back of the microwave to gain access, take a good look at the screws. Some of the screws have a small dot/indentation in the middle of the hole where you fit the screw driver. These types of screws are called tamper proof screws. And you will need a tamp...
2005 to 2008 Chevy Equinox Battery Cable Replacement
Просмотров 24 тыс.6 лет назад
Your positive battery cable can become damage due to bad layout design. The result is power is available or not for accessories however when turning over the starter doesn't turn over. And followed by complete power loss for accessories. Inspect the positive battery cable by leaving key turned to accessories and then go and handle (touch, move and or shake) positive battery cable to see if the ...
2005-2008 Chevy Equinox Coolant Bleeder Screw
Просмотров 145 тыс.6 лет назад
Just showing you where the bleeder screw is and how to bleed it.
2005 - 2007 Chevy Equinox EVAP Purge Solenoid
Просмотров 109 тыс.7 лет назад
Code P0442 EVAP Purge Solenoid small leak detected. This might not fix the problem; just pointing out the location and replacement procedure.
2006 Chevy Equinox 3.4L AWD After Head Gasket Job Issues
Просмотров 1,7 тыс.8 лет назад
The bleeder screw is the lowest point of the coolant system No need to park on a hill let engine idle not revving crack bleeder screw and wait for a solid stream of coolant not surges or bubbles then lightly tighten
I did not have a bleeder screw on the thermostat housing, so I just removed the upper radiator hose from the housing and filled the radiator through the hose, then when it started pouring out of the thermostat housing, I reconnected it quickly. I did this with the engine warm but not running.
All my 05 does is blow out steam and boiled coolant comes into the over flow tank
🔥
Got one that keeps getting air in the coolant system, no mater how many times I burp it it just begins building new air in the system....... anyone have this happen? No water in the oil oil looks great
Yes! I have about got it solved.
I just need someone to bounce ideas back and forth with because I have replaced almost the entire cooling system.
Ok...
OMG MERRY CHRISTMAS! I knew it! Your why I didn't throw it away, thank you so much!😊
Inclined which way ? Front end down' ? Or front end Up ???🤔
Up
I was wondering the same thing. lol thank you.
Your the man thank you!
The bleeding screw is 7mm. Looks like your screw snapped off in the housing just like mine did. The housing is 10mm. But im gonna try to bleed it this way as well
Thank you for taking the time to record and post this video
The man did a whole video without demonstrating anything smh total moron
HEY, I AM GOING THROUGH THE EXCACT SAME ISSUE. I HAVE SPENT MORE THATN $500 IN REPAIRS,,,AND NOTHING. I WAS SENT THIS LINK AND BOOM. YOU EXPLAIN THE EXACT SAME THING THAT MY EQUINOX 2006 IS DOING. I AM GOING TO CHECK THIS OPTION AND SEE, BEFORE I TAKE OTHER MEASURES, THANK YOU FOR THIS VIDEO, I KNOW ITS PRETTY OLD, BUT TIME PAYS OFF. THANK YOU RICHARD. HOPEFULLY IT'LL GO WELL.
Como se yama esa piesa
www.rockauto.com/en/catalog/chevrolet,2006,equinox,3.4l+v6,1431999,exhaust+&+emission,vapor+canister+purge+valve+hose,15614
Rockauto part is called vapor canister purge valve hose
part number? I don’t see it in the comments 😢
Anyone know the part # for this the screw on mine is broken any suggestions?
I just looked it up on rockauto.com and could not find it. Just call your local Chevy house and they will get you that number.
this is the only video on youtube about this
How much coolant is lost when you open the bleeder screw, a lot or a little? Just wondering in case I need to place a pan under the car to catch it all? Thanks
Hey if anybody checked this video do not just pull that like he did the green thing you're supposed to push if you have a 2007-2009 like I have it won't be a green thing will be just a white skinny thing but still you push it down then you pull the cable
Better than most I've seen
Do you keep the reservoir cap on
You can yes.
the part that you “broke off” is there a replacement part? I also broke mine
The party number is in the replies.
I've been struggling with my wife's 2008 Equinox for 3 months. Firestone initially said I needed to replace the dual cooling fans. Then they said I had air in the system and they'd get it out. Next they said I needed a waterpump and I might wanna put a thermostat on it to be safe. That was in Tyler Texas. We made it to Baton Rouge La and we're right on top of the 6 lane Bridge and alarm went off and car was overheating.Got it to a Firestone and they said I needed a thermostat and I said they put one on it in Tyler? The mechanic said we called them and they said You told them not to put one on it. Wtf man ? That would make no sense. Anyway we made it back to Tallahassee Fl and have been having problems overheating. Yesterday I used the bleeder screw and saw air bubbles come out. When I saw a stream of coolant I tightened the screw. So far so good! Thank you so much for the video!! God bless you! Let's go Brandon!!!
thanks!
This worked on my '06 Equinox! I no longer hear water sloshing around in my dash on cold starts and no more rising temp gauge in traffic, thanks!
How much coolant did you lose when you opened the bleeder screw?
@@currentcondition If I remember correctly, I lost about one cup of so fluid. While this process did work, it was short lived in my case. My head gasket was blown allowing combustion gas to enter the cooling system, this was the cause of my rising temps in traffic.
@@alyte11 Thanks for the reply. One more question, when I’m traffic did your car actually display an overheating message on your dashboard?
i am now having that sloshing sound in my dash and i have no idea why
@@intreeswetrust This worked for me a while but returned. I'm sorry to report it is the head gasket. Do your own checks to confirm rather than taking my word for it! These engines are not the best, however. I still own and drive this vehicle here and there but its not one I rely on. My temps will sometimes rise close to the danger zone while sitting in traffic. I'll bleed it, then be good for a while until it reoccurs.
Great video
What do you do if you get very little coolent or bubbles.
I took that screw all the way out… she blew up in my face and I got coolant all over me and my driveway. Thanks for the video
Did it work tho?
@@PxlarXYZ re-reading my comment the thanks sounds sarcastic but it wasn’t meant to. It seems to have worked.
Omg this just happened to my hubby and I while we were trying to burp it!! Lost all of my coolant pretty sure😭😭 would you happen to know what to do from here? So we just add more coolant and let it cool off and then try again? lol helpppp
@@ashleydeane2682 it’s been a while, but I would say let it cool off and add coolant. Definitely don’t add any while it’s running though. Good luck…
Has anyone tried this on a 09 with success? & When you have the hot air going. Do you have the recirculating on or outside air circulation? OP you still check comments? @Richard S
You did? and have the outside circulation on. Also, double check because your Nox might have two release valves.
@@richards758 I tried it for about half hr. Got bubbles 3 different times. What point should I say it's the head gasket? & when the air is going, do I have it on recirculating or outside circulation?
@@CKnight88 Outside circulation. Also, what's going on? Why are you having to do a coolant system burp procedure?
@@richards758 2 months ago had heater core replaced. Started to hear water noise in dash. As it got colder the heater wouldn't blow hot like it did last winter. Took it to same shop they did the heater core. Explained the noise. They said it's the head gasket. Car has never over heated or needed coolant. Checked coolant 2 weeks ago. Level in res was good. I'm just unsure if it is the hg or they didn't bleed it properly in the first place. Plus now the heat doesn't work. It used to work while accelerating or while parked I'd hold rpm at 2500rpm and it'd work.
@@CKnight88 have a shop do cylinder compression test and go from there. If it is the head gasket, there's vids on RUclips that show you how to do it.
Will this work if my car is up on jacks as opposed to an inclined surface?
Yes it will
How do you take the battery out. I'm so confused
Chevy Equinox Starter fix ruclips.net/video/nKMJcYSjG30/видео.html
Hey, would you by any chance have a video or a follow up how-to for the actual replacement process?
thanks it would seem your video is still helping! it just helped me. keep posting help videos!
Glad it helped!
What’s the piece with the green called?
That is the/a service hose. Someone posted the part number in one of the comments. You can also call the chevy house and ask them for the part number. That hose connects to the EVAP Solenoid. Supposedly, this is the part #12581282 but please make sure it is.
My heater doesn’t work unless I am moving. It also over heats when I am idle. Right when I start moving every works again. I was told I have a bad heater core
Water pump
What was your problem? I have the same issue plus the air bubbles on the tank.
My 2008 had the same exact problem. I changed my thermostat and changed the coolant and she was fine.
Hi Richard I followed all your steps and it worked for a few days but I keep getting air in my coolant. I changed my water pump. I change the thermostat 3 times but for some reason I keep getting air in my coolant any ideas please help me?
Maybe check your hoses? Also a visual inspection of the hoses when the car has hit normal operating temperature might give you a hint.
@@richards758 when you say check your hoses exactly what do you mean please?
@@richards758 Also thank you for responding so quick
@@theseattlegreen1871 Make sure there isn't any leaks happening around the hoses. Start with upper radiator hose and look for hairline cracks, check the underside of the hose, follow each hose in/out reservoir and into the firewall, back out the firewall, into engine, out the engine.
@@louie1487 Do you think there is any way it could be my radiator or my heater core?
Gracias Mi amigo this video helped tremendously!!!
Un placer mi amigo!
** THANK YOU SO MUCH FOR YOUR VIDEO. WE ORDERED THE FUSES AND GOT THE SPECIAL TOOLS ON AMAZON AND FIXED IT VERY QUICKLY WHEN THE PARTS CAME. THE HARDEST PART WAS GETTING THE COVER LINED BACK UP TO PUT ON. LOL
Mine started smoking about 3 month after i uploaded this video. I don't think it has anything to do with the fuse. Some other part gave up and i was lucky it happened a couple of seconds after i turned it on. Please be careful with the unit.
What a homie, thanks man. Think it solved my issue 👌🏼
Glad it helped
How much coolant did you lose when you opened the bleeder screw?
We did it
P0455 evaporative emisión system leal detected gross leal /no flow.alguien me puede ayudar por favor?
Tienes una fuga en el sistema de evaporación o el solenoide está fallando
si me disen q tiene una fuga grade i el solenoide ya lo puse nuevo i siempre. gracias
Is this the same as doing a coolant flush?
Nope.
best seen so far thanks for sharing
Wow, thanks!
Do we close the coolant tank cap off or does it stay on?
I actually leave it off for a couple of minutes while burping when the hoses are not that hot to be able to squeeze them and help burp faster but then i close it once the vehicle starts warming up.
@@richards758 i did reverse coolant flow on the heater core instead on my customers Pontiac torrent, it worked it’s blowing hot air...I just put the hose on the other hose terminal on the heater core...heater core was plugged but I will change it back when new heater core comes in...and we will charge him $2000???? 😶
@@KFLson by
Wow thanks for the video proof. Heard of but never actually seen a 10mm socket before. Thank you!!!👍🏻🍻
😂😂😂😂😂😂
Great video! That is exactly what my sisters trailblazer is doing. I replaced the starter for her today and of course nothing! I was like wtf! I noticed her truck doing this exact thing so I thought ok now your battery is shot. I would get power at times depending on how much I messed with the positive cable. Now after watching this i know its the cable. I feel bad cuz she paid me $50 to change the starter and its not even the issue.... but I still changed the starter. I don't even want to attempt changing the cable out but I know shes gonna ask me to do it. Thanks!
I change starter 3 times and alternator 1. Still works for one ride and try to turn on isn't working again. For sure this is the problem because the battery saver light turn on. Mechanic still said battery is good. What can I do. ??
leave key on accessorie and have someone seat on drivers seat looking at the dashboard then you go and shake the positive cable. If the dashboard lights start to flicker (of you hear that clicking noise that comes from your throttle body's butterfly) then you know for sure your cable is faulty.
I try to turn on is only a click sound. Everything on accesories turn ok.
@@arelimty looks like it is something else then....take it or call in an electrician....maybe check fuses and relays
What if my heater is broken? Will it still have hot air when bleeding?
Smoke test or soapy water and air to see if it leaks from the valve