Видео

Awesome,Thanks

Could u use something else instead of bleach I'm allergic to it 😊

Just done this and it on the 2 is that ok ? Was on 0

How do you stop it sticking again ?

Awesome cheers mate

Must taken hundreds these to the scrap yard for exactly this problem. We fix the odd one it's almost always this problem caused by overloading.

Funciono! Gracias

i cannot get the belt back on how did you do it for me it’s incredibly hard to stretch it back

Hi Darren got the new parts, just fitted them, now it’s heating up but getting very very hot? Any ideas on what might be causing this? Thanks mate

Hi Darren just adding this comment here incase you don’t see my previous reply, I’m not getting a reading on a continuity test from either part (I getting one from the wire ports as shown in video) Is it possible they’ve both gone? Thanks in advance for your reply.

Excellent lol this worked

ok, but did anyone have problems with the actuall drill before doing this trick? then why bother, just tighten it as much as possible

Could you please guide me on what to do with an E21 error code on the hoover dryer, with a water part at the bottom, I’ve cleaned the thing you have done too, just not working :/

Brilliant, thank you.

I have the blue fill tab but doesn't do anything when pulled. And reason why this would happen?

My one doesn't open at the top. Where the two screws at the top should be there are two rivets, so it's impossible to open.

Me and my mom got a broken key out of the lock that’s to this!

ur case is wild bro

Does the green light always stay on the receiver? We have a fault 1032 on our thermostat that won’t go away. We have a pairing fault message coming up. Thanks

I have the same issue but my windows only have the bolt that pops out on the upright part of the frame, any suggestions would be appreciated

If the heater has the correct resistance readings and is drawing current, can it still be thrown away?

Jeżeli grzałka posiada prawidłowe wskazania ohm, pobiera prąd to może mimo to być zużyta?

How did you actually get the belt back on? Must me a knack for that?

ThanK for the vid. I have a heater that won't come on at all..There is no power going to the switch. No fuse tripped. Fault on the consumer unit? I also have those tow dials, with day and night set to +2.

Which site do you buy the element from?

I'm trying to reset mine but what are the +4 and-4 on the fuse board for ??? Oh by the way mine are working but instead of coming on at 11pm onwards it doesn't come on till at least 4am and that's almost out of cheaper electricity rates ,I'm in Ireland so their expensive to run

Bollocks this

I don't have that box in my boiler

Whats the difference between the white dotted therm and the yellow dotted therm?

Great video. Used this to determine the fault in my exact same dryer. Keep up the good work

Thanks for the help

Do you keep heating on or off to do this mate ?

I cant find green ring but i have the cartridge. I cant workout how to get it out???

I had the same issue and was having a tough time removing the seal. Thanks for the video showing how to remove, thanks!

Thank you brother i from italy

I dont get it😅

Thank you

@darrensdiy4769 i am trying this on my dryer which is running fine but not heating up anymore. i am not sure how to remove the white caps from the thermal cutouts. do i just pull them off really hard or is there some trick to removing them? thanks for the video!

My mum has this boiler, and her pressure has dropped a little. I've tried turning the black lever as you said but ours isnt going up, I dont know what to do

B.G. Installer told me to leave alone the big white key & just use the little white square one , yet every yt video says to set the big white key ? Confused .

Bet that smells nice

Bold of you to assume i have a chisel

I just replaced the whole heating element (done it before on old dryer) . Worked fine but could smell burning. Online said that’s normal with new element & dust kicked up. Checked back later and not heating up. Don’t know if I have a bad one and can get money back. However I do have the relatively new element from the previous dryer. Motor went on it so not worth replacing. I kept some bits thinking that it could come in handy. Anyway, my question is, are the thermostats generally the same? Only reason I couldn’t use the old element was the plugs being different, apart from that it looks the same.

What do you do if that method doesn’t work ? Either pins are stuck or not enough space to get in ? Thx

It not working with me

very useful thanks

God bless will try this and get back to you

Any ideas, at all, as to why I don't have a bloody pressure gauge on mine? None where yours is (which the manual says should be there...) Checked a few places...

Use tweezers before the blade snaps off

Got it! Thanks