Видео

These direct drive motors you can connect up to the controller or any other controller. This is 60v controller. The different controllers do come with wiring diagrams. ciao.

You do that across the coils. Thanks for watching. ;)

So yes. Direct drive will take care of any mechanical loss, and you will see even better results. But I did this because I needed more speed on my tests. So I gear with belt. Just for tests. BEMF is tapped across any coil, or multiple coils. Put your multi meter on AC and your probes across coils, and see the magic. ;) Thanks for watching and commenting.

Thank you Brent! aluminium will never give you the performance as copper does. Cu will give more torque on motor and more amps as pmg. Link two dd together and make one a motor another a pmg. Dead short the pmg side. Keep going you will learn a lot for your own benefit. Thanks for watching. cioa

I personally don't think anything is free. Especially not this. It might be efficient, but not free. But if you want to learn more about PMG and brushless motors, you will learn a lot like this. Thanks for watching. ;)

My tests show me this rig can generate 800watts max power. It is not enough to change the world. ;)

Sorry for that. It was not on purpose. So, if you meant the charge on battery from the generator, well when RPM goes up obviously output voltage goes up, like you prob know it is a frequency thing. I cannot remember the details, since was a while back. What was amazing about this setup, was that as everybody knows, when you have a setup like this, you never get a perfect sine wave coming out of generator part. Ever. I got the most perfect sine wave I've ever achieved. Perfect. Thanks for watching. Hope you also get something spinning. It's exciting and you never know. :)

TY

You right. At the moment with this config can only charge batteries when the sun is down. And no grid. Other than that I do test theories and ideas. It is concept only. You could do some battery charging if you have lots of wind, or running water. It works at low rpm. Thanks for watching.

Sure thing. ;)

Hey. Thanks for watching. Rewound. There are plenty rewind configs on youtube. Good luck. ;)

I had engineering shop figure it out. There are designs on internet that you could try. I could not get it right. Thanks for watching. cheers.

;) TY.

I tried them all. There are a lot of wiring diagrams here on youtube. No torque measurements, I do not have that equipment. On different rpm the DDs sounds awesome. TY for watching. :)

www.amazon.com/ChongXiao-Universal-Brushless-Controller-Electric/dp/B0C2TPTNRZ/ref=sr_1_23?crid=3DT8VC92O3RPK&dib=eyJ2IjoiMSJ9.o4RRxkBy9WM7hu20_L5CjnX10ZaRNgVQHVRcgeypWThXDUiFKLt6uKb96R0-T1fOF25N3n1vEK7hODTFkP92pj-XvyJxTWGVwXxA_vtoacvZSKM8KKoDgAiozWoybSfSIK0ZNpOUHx0SVoPYTcSlRHIojES25tTV9OuRiRY5DgrbZ9ZbJjchAkYXmLART_8H16wxOYoWQMoTsaq123rvVj-fvX40_We_LS-LSqGZ-LdwL_J77Mfw_lqFz90D6Ia2-8PdeatWkK-7qNyL79PGrmT1fB-F3y7cIzspCh7VBRg.PoNe9oHJXD1fLgY3tN5nxUraOJ7aFqSf1KMwLBC09jI&dib_tag=se&keywords=ebike+controller&qid=1712660617&sprefix=ebike+contr%2Caps%2C617&sr=8-23

I agree. I tested gearing ratios here. TY for watching. Cheers

Again. I agree. Thanks for watching.

I appreciate your comments. ciao

Charge batteries very successfully. At the moment nothing else. Some people made their own e-bikes like this.

TY. Good luck.

Yes. At the moment. Burning some lights, and using the batteries again.

Thank you for watching and comments! Cheers! ;)

TY

Hey. So ALL my motors came with alumium windings. There is a DEFINIATE improvement if you rewire. If you use voltage as your primary driver, and not current, you will also wind it with thinner wire. I did 0.65 mm. In South Africa I bought these at a washing machine parts outlet and this is link to part no www.tecsareco.co.za/product/stator-assembly/5306 . thanks for reading and just have an awesome day man. Good luck with your efforts. ;)

@@jakesvandermescht694 Thanks for the reply. I have a custom rewound copper one I've done tests on. I bought one with a different model with Y on the end. Supposed to be pure copper already. I rewound one with 16ga and cut most of the poles off. I've done similar tests as you have, but with a different PMG style than the drum motor. The drum is a great prime mover.

Yeh off course you can! You can drive a fan a couple of meters high with this. The torque is insane. Thanks for comments. :)

Them motors are pretty cool in my opinion

Thank you for watching. Ciao.:)

Merry Xmas to you too. Thank you! Gerard had an custom made controller. Everything starts and stop with the controller. Thanks for watching. ;)

Great suggestion. TY. :)

Please add more detail. And howto. Do I do the neo conversion on the alternator? Or just like that? I think that the alternator needs way more rpm. I might be wrong? Anyway, thanks for chatting. :)

Hey! Thanks for watching. Please give me more detail on your suggestion to try. I do not understand. ;)

@@jakesvandermescht694 On my channel ,schematics and vids with this Bro

hey. Thanks for watching. This was a phenomenon which is still unexplained. I will get back to the project and update. I will do sideways videos. Im not good at presenting and doing videos. My apologies and again, TY for commenting. ;)

Hey @unitittii. You are right. I think you can find free energy, but not enough to make sense. Taking two metals and pushing it in a couple of melons in serie gives week or so light with LED. Same with earth batteries. Free energy. Not useful. But I am not trying to find free energy. I am trying to spin a motor as efficiently as possible. Pushing that boundary. Thanks for watching I do apreciate the conversation. ;)

@@jakesvandermescht694 WHY IS THERE FREE ENERGY ? The conservation of energy presupposes that the mass inertia always remains equally strong in all directions. But this is not the case and the most obvious proof is that permanent vacuum unrest by which all matter is shaken around. To shake a litre of water back and forth as rapidly as Brownian motion can, you need 10,000 Ps, assuming that the inertia is constant. However, for over a hundred years it has been observed that masses that are strongly held can take on slightly less inertia than when these masses are set free. It is about the same amount that the bound proton is lighter, more inert, than the free neutron. It is the difference of half a hundredth. But this is only an average value, because it was discovered that all measurements are subject to extreme uncertainty. This uncertainty principle claims that if the speed of an element is to be measured as precisely as possible, then the location of the element can no longer be determined exactly. In other words: You never know exactly where the element is, because it is caused by the vacuum to make completely unpredictable swings. A single element has an extremely small detection head to attach to those highly filigree nodal formations of inertia mediating structures. The next highest inertial diladation was then found in the weight difference from hydrogen to helium4. Instead of assuming a restriction of motion, Einstein invented a formula that declared matter to be a gigantic store of energy. Energy is compressed into matter and all bursts of energy would then inevitably have to dissolve matter. This thesis is stringently refuted by the perfectly proven, eternal stability of the basic building blocks. Even the Big Bang believers, who think that matter "froze out" of energy at that time, nevertheless assume that it will still be there in trillions of years. Such obvious logical inconsistencies can nevertheless no longer clear a now highly decorated theory the way into the wastepaper basket. It is not only religions that are so stubbornly conservative, so eternally outdated, but also science. Behind the former is the salvation of the soul, whereas behind mainstream science, which has lost its way, big mammon has spread.

Thanks and thanks for watching!

Scott I went the more expensive way, I got engineering company to make me. There are plenty videos on youtube how to make your own. Good luck! :) And thanks for watching!

You bet! ;)

@@jakesvandermescht694 have you looked at Mantim Lee's feasible study on the Gerards hyperdrive? He is almost correct but his controller design didn't work, it had a few faults and key components left out. I'm hoping I've got it right now, just waiting for the new PCBs to arrive.

Do yourself a favour. Build a controller that can pulse 10kv + into the drum motor no more than 2amps.... See what you reckon. I'd love to chat if you are interested. I'm also from South Africa, now Australia is my home

@@iseeyou7622 You are correct. It all starts and ends with the controller. jakes@tesrac.com

Sent

Thank you and thank you for watching.:)

Thank you. And thanks for watching! ;)

permanent ferrites. Neos makes the drag too much. Thanks for watching man. :)

Thanks for watching bro. ;)

energydreamer See your other comment. Did answer. Thanks for watching! :)

I use Tritans wirings, I have a couple of different ones. @tristanmcnabb2741

Truly is. Thank you for watching. Hope to hear from you often. ;)

Hey Neural Awakening. Yes it is. I got no value out of them currently. They not tuned in resonance. Still have to do that. Might get more value then. Thanks for watching :)

Awesome idea! Will it work on gel batteries? Surely not? Thanks for watching friend. ;)

Thanks for watching! :)

@@jakesvandermescht694- Question about the washing machine motor setup and testing. How do you mount the stator and rotor for your bench testing? Did you have to have a custom set made or is there something a person can buy off-the-shelf to use? Thank you!

@@energydreamer5347 I had it custom made. There are lots of videos how to do it yourself. But I am not that good with welding and fitting. It has to be very precise since the distance between the coils and magnets must be like 1mm! Hope you come right and get to swing it. :)

I am still looking for ways and means to have the direct drive motor running what size of controller and if like some guys do on videos the use only one chip IRF 3205 but when I try it keeps browning up the transistor. I am stuck and in the jungles of Rwanda where components not easy to get. Any idea or directions?

Hey KEnergy. No. The motor and pmg runs smooth and taking very little input power when I am not taking load(amps) from PMG. So if I disconnect the pulley belt, and run the motor by itself, Im on 40 watts! It is really efficient for such a weight(48 magnets and steel rotor). When I add the pulley back(1:2 ratio to pmg) I run at 104 watts at speed. This now is with the torque of the 1:2 pulley, two sets of 48 magnets, and two steel rotors! Imagine replacing the rotors with carbon fibre or something. On the bench todo list ;) Thanks for watching my friend. For those who do not know KEnergy, go over to his channel and shop. This guy has some amazing inventions, working and selling. Not a lot of people get to that stage. Respect. @kenergy1707

@@jakesvandermescht694- I can attest to this statement regarding @kenergy1707 channel and his online store. Good stuff and no fluff - always straight to business.

never did 100v input to motor. I have 60-64v dc. You will read that on the blue energy meter. Thanks for watching! ;)

never did 100v input to motor. I have 60-64v dc. You will read that on the blue energy meter. Thanks for watching! ;)