- Видео 7
- Просмотров 2 995
Highway40garage
Добавлен 11 фев 2023
Providing video documentation for car sells and repairs for our customers.
BendPak 4 Post Lift HD-9XW - Build,Tips, Tricks
HD-9XW BendPak 4 Post Lift and our experience.
www.bendpak.com/car-lifts/four-post-lifts/hd-9xw/
www.bendpak.com/car-lifts/four-post-lifts/hd-9xw/
Просмотров: 1 770
Видео
They installed a speaker, Where??
Просмотров 185Год назад
Diagnosis of a stereo system, new installation.
Forklift on a Road?? Setting up our shop with a surprise delivery.
Просмотров 45Год назад
Getting the new shop area started. More updates to come, like and subscribe to follow along.
K5 Chevy Blazer Stereo Installation
Просмотров 328Год назад
Upgrading a stereo system in a beautiful K5 Chevy Blazer Products used: rockfordfosgate.com/ www.classiccarstereos.com www.pioneerelectronics.com
Jeep CJ5 stereo & interior upgrades
Просмотров 520Год назад
Update on the interior and stereo in this blue Jeep CJ5. Websites where parts were purchased. www.bestop.com www.bossaudio.com www.Amazon.com www.ocautocarpets.com More pictures on Instagram/highway_40_garage
Where did you find the high back seats?
@@ryanw7189 they are Bestop seats, you can find them on their website.
Is there a specific kind of teflon tape for the elbows of the feed and return lines of the hydraulic ram? That stupid flex hose drove me crazy!
No, I used just plumbers teflon. There is automotive Teflon that you can brush on works too, if your struggling with a fitting clean it up, give it a couple wraps then brush some automotive flon on it and it won’t leak.
great video, only thing i would add is sounds like you are not level or something not in sync. During the test lift the locks are not hitting at same time. They should all snap in about the exact same time.
They unfortunately never will be perfect. We always move them around in the warehouse for different cars. I also like to hear the click individually, so I know all of the safety locks are engaging.
Is there any support for the rod end of the cylinder when extended ?
No support, once the cables tighten the rod is more or less supported by the cable tension. There are pads on the top section of unit where the cables attach so it does not scratch the ramp when lifting.
I hope you will answer this question: Did you lift come with grease/zerk fittings for the pulleys?? Mine did not. The tech guys at Bendpak are COMPLETE MORONS!!!! They are zero help, and totally ignorant to the product they are selling. I'm hoping like hell I don't need any serious help from them.
Literally just 20 minutes ago I had the same experience with the flex hose and hydraulic hose. I was able to find a supplement online where bendpak talks about cutting it to length but nowhere in the instructions does it say to do that.
This week installing the bendpak hd973p triple stacker i ran into the same problem with the flex hose. First time intalling Bendpak as we almost always deal with challenger or Rotary. I ended up eliminating it and using sheath instead since there was no information on it otherwise, especially with the triple stacker .Wish i would have found this video sooner
Same issue but found this. Posting it in case it helps Anyone else. www.bendpak.com/media/wysiwyg/TSB-97-082022-Four-Post-Lifts-Flex-Tube-Kit-Final.pdf
Sorry if I skipped over any of this, but: Is that a 110v motor instead of 220 like the spec sheet says for that lift? Did you set the runways on their narrow setting or wide? If setting on the wide, do drip trays and the jacks still work?
Any issues tripping a breaker with the 110v? I have the same option and see they show Full load amps of 26 amps.
Hello 😂
Very clean install and absolutely beautiful k5 blazer
My first ride was a CJ5 but it wasn’t that nice! ❤❤❤
That is one good looking jeep