Видео

Thanks for the TRIP A/nuanced maintainance required reset instructions. Also horn test, it passed!

oh boy those bearings pile up yet bud

So what did you do for a cooling system?

I like your work ❤

Instead of using soapy water as a lubricant, how about anti-seize? will that work too???????

Thank you great job short n simple

Thanks dude. Great video

Did this "fix" the problem or did irt just go away for a while? Please let me know. Thanks

Thank you so much

Thanks brother!

After searching for a way to fix this problem I came across your video- best one for sure! Thanks

Now pull the yoke out 😂

Yeah it did it but I don’t see it doing very many of them before it says no more, if you have access to air just use a pneumatic 3/4” and be done with it

My milwaukee 1" d handle has never met a nut it couldn't remove yet... those drain pan bolts never stood a chance.

The dewalt 1/2 inch is only 200$

Ryobi sells a 1/2 inch high torque impact wrench with 1100 Ib/pd of breakaway torque for about 140 on homedepot with a free 4ah HP battery and charger.

How to ruin your cabin air filter.

Link?

Bro finna get lung cancer

🤦‍♂️

You just saved me $475. God bless brother

Thank you!!

High hooked and didn't xhecky

When you park your truck, pull the trailer brake and back the truck against the trailer and then pull the truck’s brakes - by doing this they will be unable to unlatch the fifth wheel. This is a truck of the trade - regardless one should always double check before you pull off on the road.

He pissed off someone.

Someone disconnected the 5th

Pretty stupid and Dangerous design, for the truck to just shut off without notice. I’m about to install a aftermarket low reservoir coolant audible buzzer alarm to alert the driver rather than the engine shutting off.

You did real good!

How much weight do you gain with floor framing?

I've been driving with Orange light for 2 weeks "Coolant level sensor problem detected". Then SPN 111 FMI 1 came on "Coolant level is very low" with Check Eng. and Stop Engine light ON, when actual level was full, ok. I drove with that for a week, truck didn't shut down. Then right before changing the sensor I took a flat screwdriver and bent (just a bit) two contacts On the Sensor. Put the plug back in and ALL LIGHT WERE GONE. No problems for the last 3 weeks.

Thanks brother I did it Thanks to you

I know this is the same video as I watched last time because I remember you honking the horn lol and it worked for me in the past, but my check engine light came back on and this old trick isn't working anymore

:::ATTENTION:::: Don’t follow any step of this video. This guy has no clue what he’s doing and people are going to destroy their axle housings/hubs/bearings by following these methods. 130ft lbs is grossly over tight and is preloading the bearings. These bearings are also lubricated by gear oil in the hub, there is no reason to grease the bearings. I hope the author removes this video. I’m curious as to how many bearings have failed due to this horrible excuse of a “how to” video.

This saved me !!! Thanks !!!

U got zero oil pressure

Thank you for information

Do you have any tips on how to remove it from the stock wheel to install into the new one?

Come back every time. I appreciate you 💪

Thank you sir you just save me some money

Mine just started doing this yesterday I’m hoping this will fix it or it may just be low on fluid. So I’m hoping for the best Transmissions don’t grow on trees

Turned out very nice

Who knew that all the matrix years are different im Glad i found 2009

sweet deal, thank you

Praying this solves my problem!!!

ty just bought a 2000 and am looking forward to applying your knowledge yet to ride her but was told she had a frame off at Some point in her history not looking to race merely enjoy as a new 2 stroke rider normally i ride d/s 1998 xr650l and 2014 xt250 my go to favorite)

GOD BLESS YOU BRO

09 freightliner cascadia, my yellow and red started flashing, and my truck turned off. I got two more days of work is it safe to continue to finish my two days or rather just stop.

I have the exact same truck. Bought it new and it’s still my daily driver 22 years later. Nice job on the rebuild. I’m sure you’ll get many years out of that baby.

Like the restyle

Mine does that when I turn left