- Видео 4
- Просмотров 94 898
carsDAN7172
Добавлен 26 ноя 2011
Fixing stuff easy
Cub Cadet 34” 3 stage drive belt replacement
Replacing the drive belt.
1. Tools needed. Safety glasses/gloves, 8mm socket, socket wrench and extension. Blocks of wood. Handy to have a screwdriver or boxed/open ended wrench or pry bar. Smaller hammer. I cut the flange on the chute to access a bolt using a sawzall and metal cutting blade. If you are going to replace the auger belt too, you'll need a 9/16 and 3/4 boxed/open ended wrench or replace the 3/4 with a crescent wrench. Magnetic bowl or somewhere to store the bolts is suggested. Wire cutter/knife to cut off old belt. Something to lay on to to get dirty and/or stay warm. Have an emergency plan in place in case you get injured--let someone know what you are doing if you are by yo...
1. Tools needed. Safety glasses/gloves, 8mm socket, socket wrench and extension. Blocks of wood. Handy to have a screwdriver or boxed/open ended wrench or pry bar. Smaller hammer. I cut the flange on the chute to access a bolt using a sawzall and metal cutting blade. If you are going to replace the auger belt too, you'll need a 9/16 and 3/4 boxed/open ended wrench or replace the 3/4 with a crescent wrench. Magnetic bowl or somewhere to store the bolts is suggested. Wire cutter/knife to cut off old belt. Something to lay on to to get dirty and/or stay warm. Have an emergency plan in place in case you get injured--let someone know what you are doing if you are by yo...
Просмотров: 2 214
Видео
2011 to 2019 RAM 1500 Classic drivers side low beam headlight replacement--on a 2016 RAM 1500
Просмотров 42 тыс.4 года назад
So, if you watched this vid ruclips.net/video/AQPi68KefCA/видео.html he removed WAY TOO MUCH and DIDN’T show you this white clip that releases the headlight. My video shows you an easier way PLUS the white clip and how to angle it down and up to release the headlight. I didn't find a video I liked that showed or described how to find the white quick clip that you have to reach in and push up (b...
4 wire trailer harness connection
Просмотров 376 лет назад
How to wire harness 4 wire two light trailer what the manual and other videos don’t show you!
Replacing HID D1S bulb 2009 Chrysler Town & Country
Просмотров 51 тыс.10 лет назад
Ok, I did this video after I completed the install. I had no clue it would be as difficult to replace as it was otherwise I probably would have started doing a video before to capture each step. I'll try to respond to comments I did this 4 years ago and just received the first notification that someone commented on this! I had no idea 25,000 views occurred! Thanks for watching!
Great vid
I just reached in and took the cap off and replaced the bulb. You did a tremendous amount of unnecessary work
Thanks so much Dan for this video. I guess once the assembly's out, changing the turning light can be done too. Best regards
Thanks, if only they stuck with the older style metal L bars, they were tool free and took one minute to change a headlight
do you know how to stop those stupid center wheel covers from falling down???????
I do not. Of course, I sold the van many years ago. Maybe some loctite or superglue?
Thanks simple short video exactly what I need
And I thought replacing the bulb on Silverado was a pain in the ass wow piss poor design but thanks for the info !
Thanks for checking it out!
Bro take the grill off!
That way could work too.
Thanks for this video man
You bet
Thank you for the video. Removing the driver side bulb is easy but when I tried to insert the new bulb and twist it does not stay with the electrical connector facing down (6 o'clock) but rather at 4 o' clock. I tried to insert on several points but did not manage to find a way to twist more. When inserting the bulb did you screw it clockwise or counterclockwise looking the bulb from the perspective if you were on the back of the car?
Wow. I cannot recall. I just had to remember how I took it out. I probably messed up and didn't explain that in the video. I assume from the direction you are saying it would have been clockwise.
Talk about a pain in the ass for something so simple
It would have been nice to see any tricks you did to replace the boot (rubber cap) over the rear of the assembly. I have spent 2 hours, and still the boot would not completely go on. Perhaps you know something we don't. 2011 Town & Country Limited 3.8L.
I don't think I did. It wasn't worth the time or effort.
Dan, thanks for the video. Made upgrading the lights on my 2019 Ram Classic a breeze. This is one of the stupidest designs on the planet but thank God for RUclips and folks like yourself to save the day!
It is a stupid design but it’s got nothing on a Honda Fit
I needed a refresher, I took the entire grill off. Made things really easy actually. The grill just pops right off and gives you easy access to everything.
You should change the title to "talking about replacing the bulb"
Maybe! LOL
thanks for the video
You're welcome :)
There are at least two other videos that show exactly how to do it. I watched them and replaced it. $18.50 for the bulb from Advance Auto Parts. 20 minutes to take out the old one and put the new one in and test it. It shined brightly.
Yeah, some video later improved on mine. I didn't think to record it when I did it. And no videos were made to help me at the time. Glad you found some that helped you.
Thank you for the overview! Definitely made it easier to start once I knew what to expect. Here's a complete start to finish from my perspective. Didn't really take very long to replace. ruclips.net/video/PlVJUsjz-z0/видео.html
You're welcome. If you have a 2011 to 2019 Classic Ram 1500, I just did a drivers side headlight--but this time I showed each step. :)
So you don’t friends or a significant other that could film you doing this?
Martin Gradias I didn’t think of it until after I completed the repair. And I had no idea this was going to be as difficult as it was. In hindsight I would have.
I dont understand sorry
Again, I did the video after the install. I made the video in part to describe that there is a small metal clip that is difficult to see--it holds the bulb in place. After the clip is removed, I found that it didn't have to be re-clipped as the bulb would stay in. Using a phone to record a short video helped me understand how the clip needed to be removed.
Dude you deceived what you did the purpose or a video is to show the process?
I had previously done the repair--I added some comments above regarding this. Deceived? No--I clearly explain how to do it. It would be impossible for me to do the repair and handle a camera at the same time. Trust me, you can do the repair if you listen to the video. :)
I will never buy another Chrysler product again. I have a 2010 TnC limited and changing one of these things is pure hell. you have to take the front pumper and grill off and then undo 5 bolts for each light to be able to pull out the light casing to change out the light. all that just to change a headlight. THE worst engineering ever, but it's all designed to make someone go back to the dealer to get raped($400 to change out a headlight is theft...period). it is possible to reach in there to change the bulb without taking the front pumper and grill off but you're at great risk of damaging the bulb as you cannot touch the bulb with your hands. I did it that way the first time and it was just as much of a pain. this video isn't going to be of much help as it does not show the procedure. it's HARD, no matter how you go about it, but it's definitely doable and better than taking it to a dealer to have them steal from you. have fun...but you actually won't.
I agree--the engineering to replace a bulb on this thing was more difficult than it should be.
is it also the same on a 2013 town and country???
It might be. They did change the body in 2011 so it could be slightly different.
Chrysler wanted $240 for the bulb and $120 to install it. Warning that is was a under pressure and could explode if I was not careful. I hard a hard time disconnecting the square metal base from the line and also putting the collar back on so pay attention when taking it apart. I followed the instructions in this video and put it in myself and only paid $90 for the bulb at the local Advanced Auto part store. Yeah to RUclips and its contributors.
Debbie--you are awesome! Way to go! :) Yes, the metal clip piece is tough to disconnect and seems pointless to re-install. My bulb is still going strong after all these years.
I changed the high beam passenger side bulb tonight. It cost $18.50 and actual time taking out old one and put the new one in was about 15 minutes. Took about 10 minutes to go buy the new one and get back home. Advance Auto is close to me.
Well done! I couldn't have avoided the 400.00 extra cost w out you!
Awesome, you rock! Thanks for watching!
I'm having a tough time removing the black plastic ring from the old bulb to put on the new bulb (the ring that locks the bulb into the housing) anyone have a clue? This video didn't help...
It's been quite a while since I did it--it was a pain. I might have used a tool like a pliers or screwdriver.
My drivers side HID bulb keeps blowing after a few days. I can't keep paying so much for a bulb that doesn't last more than a week.
You must have defective bulbs or some overload issue--the dealer will have to check your system.
Thanks for the vid. The fact that you didn't show the process wasn't a problem for me, it helped to know what to look out for and which way to twist things. However, changing the passenger side (driver's side for UK like me) is harder as Chrysler decided in their wisdom to put a huge airbox right behind it so you can't get your hands in to change the bulb. I had to remove the entire airbox to get access. Once you have, the process is the same as here. Saved £100 on what the dealership wanted to charge.
Thanks for watching. Yes, I was going to try to check the passenger side to see if the process was easier than the drivers side, but after seeing the airbox in the way I decided it was not worth it unless I needed to actually change the bulb.
Why wouldn't you have filmed actually doing it?? What a dumb video.
I didn't because after doing the repair I realized that 1. I couldn't have filmed it and did the repair at the same time unless I had a helper 2. that the repair was sufficiently difficult enough that I should post a video to at least explain the process. Don't be such a hater. :)
what a waste of time. worthless if you don't actually do it.
Actually I did do the repair--I made the video afterwards to inform people that it is difficult and to help them through the process.
balb
I win! Thanks for the how to. It would have been a bit better if you filmed actually doing it - but I managed. I was still afraid to touch anything even after I disconnected the battery. I had to work my way up. But take that stupid expensive headlight. I win. That is all.
You did win! I wish I would have tried to film it while I did it...but the repair takes time and you need two hands so I couldn't really film it. I did it afterwards to help people. I'm glad you found it helpful--and you won! :)
did it need a ballast or just the bulb
Just a bulb--the old one is shown. I'm not sure what ballast you are referring to.