Видео

appreciate the video, looks like a straightforward fix. thank you

WOW... that is an awesome tip!!! Thank you so much!!! 😊

Those plastic bowls warp when removed, you should have bought the aluminum carb bowl for replacement. OMC only used plastic bowls on G4’s for 4 years and went back to aluminum in like 1993 or 1994.

Very helpful for me. I will go ahead and do this myself after having seen your video!

Can you show me how the blower mounts to the front of the tractor

Do you leave it run all night?

Can i have a pin❤

Hello, thank you for your videos; they are very interesting. I also have a Eurovan, although it is a 2003 model. However, I have a problem: my air conditioner won't start. It might be an issue with the compressor. When I bought this car, the previous owner told me that if the air conditioner stops working, I should touch a wire connecting to the battery's positive terminal, and it should start working. However, recently, it stopped working even when I do this. I would appreciate any advice.

Free pallets 😄 Great job buddy

Now how do we stop it from overworking the 01p/01m trans 😅

As your fifth grade teacher said “show your work”. My bolts don’t want to come out. Did yours just slide out?

Can you give some details on that fantastic mounted fan above the galley?

Does this permanently disable auto start/stop every time you turn ON the MINI? Thanks.

How did you prep the panels for painting and what paint did you use? Thanks :-)

Now that you've had them for 9 months, how do you like them? Did you have any trouble keeping them clean?

Did this fix your noise issue?

The belly pan does fully detach. Two small nuts at the back to disconnect from two rubber vibration mounts, and then remove the back part from the slots. Thanks for the video..

Gimme my big ass speedometer back

This is discussing, bring back the old mini.

Nice install Cheers from a Swede in Mexico

Liked and subscribed. Great looking bike.

My 2021 gear shifter is flashing all the lights for some reason. anybody know why?

Where the heck does this go, you should have filmed before removing it.

Can you post a link for the tensioner pulley you found

Thanks for the video. I replaced mine because of it. I had a problem going from front to back. It was easier to meet in the middle because I couldn't secure the last hanger. Is it ok for the donut gasket to be exposed to the weather?

Just one belt? or does it have 2 belts..maybe replace the idler pulley at the same time just to have a fresh bearing.

Why did you remove the entire stabilizer and even with the stabilizer struts?

I have a 2022 f3 limited I think I might have a bad oil pump…do you have any recommendations to check to verify the if I am right….. I have checked my oil hot and cold and it reads the same,that was the first thing I was told to do because it won’t shift into gear.

Sorry for the poor audio. This was the first time using the Gopro on the bike and I had it chest mounted. I have since mounted it to the helmet for a better view and I am looking into getting an microphone that I can use inside the helmet. Does anyone have any recommendations?

Where did you get the passenger cupholder?

super helpful, thank you.

Can you remove the drip tray when you’re changing the filter?

Thanks for the video a little dark but really helpful .

Do you have fans blowing directly into coop or blowing out the coop

Why not have a swisher plow? Uses the same mounting frame. Would be a lot easier to switch them. Just leave the frame on

What happened to simple gear Collector

I can understand the "saving money" part... but what about the other blend door that's above the hot / cold door that you fixed? I believe it's the one that directs the hot / cold up or down.

Hello I've got 2011 Corolla and when I start it it idles rough and engine light is now on. Seems to just be idleing rough and doesn't sound the greatest when you first start it. Would this cause the check engine light to come on ?

Can you top off fluid via the dipstick?

Do you need to bleed coolant afterwards?

Merci. for your information vdo

Ummm, yeah, i think Amazon might save me a lot of time, plus i don't have a woodworking station at home

Great video! About to do this as well. What bolt kit did you go with?

Thanks brother

Would have been a great video except it was done in the dark. I felt like Ray Charles.

Thanks for posting these videos. Off topic, what engine cover do you have? Is that from a Jetta?

IS THERE A SUPPORT BRACKET ON THE END OF THE ROLL BAR ON THE FRONT BELT PULLEY THE BAR IS NUMBER 23 ON PARTS DIAGRAHM ITS PROBALY A SADDLE BLOCK I NEED ONE

Do u no wat size your belt is

Do you need to do the other side of the window too?

Thank you