Видео

hi, may i know how was the wind noise? and solution you fixed for that or its no wind noise at all?

Great video. Very useful.👌

Just come across your channel mate, I like the way you go about it :)

awsome man for sharing all your videos, i have the same cruiser so very useful, I watched your uhf install and did mine following your guide!

I noticed that you still have rubber mouldings in the roof ditch. Wouldn't water pool in those mounting areas they they can't run off the to the sides of the car when it rains?

How are these draws holding up

Have you worked on the LC200 2017 onwards? Managed to change the bulbs ?

Thanks for video. Was really helpful. Could you link the tie down you used for the fridge at the end? Cheers,

My genuine bonnet protector has lanndcruiser printed on it😂

Will this work on my 2013 LC based on the US spec

Great video. I found low beam lights to provide a blotchy spread of light when setting them to get the right road coverage. Did you experience this?

Great install video! How has the wind noise been with this rack?

Can confirm that re setting the bolt eyelets in the roof if you knock them out is a complete and utter bloody nightmare to re seat. Be patient and careful fellas!!!

Gudday, I'm trying to install my headlight protectors but for the life of me I cant pry up that rubber strip to put the clip under. It seems glued in place and I don't want to force it in case I break it apart. Any tips?

For those viewers with a Sahara or VX with a sunroof do these racks allow the sunroof to still be opened ?

Seems like the LED is installed in an angle? not 90degrees?

Was your list of required lights ^ just all the exterior lights and interior lights? Not including license plate?

do you have audi grill and bumper?

As far as the rear dome light replacement goes, you can actually remove the plastic cover and put the bulb in without taking the entire dome assembly out of the headliner. There are two small tabs on the forward side on either side of the switch. With a small screwdriver (carefully) or a thin trim tool you can pop that cover off front to back. Then you don't have to mess with the little metal thing and the bulb seats easier. also, the bulb size is fairly important, so go with what he's telling you on that. Great video for a 200 Series Land Cruiser owner. Thanks!

Hey mate, With the spacers, plates, bolts etc did these come with the 200 series fitting kit- or did you need to use only the components in the standard fitting kit that came with the draws themself Thanks

Hi Shaun, thanks for the video. Unfortunately install didn’t go smoothly for me. I had trouble getting wiring through the firewall on the LC200 as access was restricted. Also found the suggestion of running power for the passenger side footwell fuse box didn’t work as access was difficult and when I finally managed to get the new piggy back fuse installed and the earth lead wired to the chassis as you showed I couldn’t get voltage of better than 8V to the radio. I ended up running power from the battery through the firewall directly to the radio and got a good 12+V. Once again getting cables through the firewall was a huge pain. Thanks again thou as the video helped get me started.

Nice tutorial thanks. I wish you had shown where the “fire-wall” access is on the LC200. I’m not confident I know where to piece the firewall?

Basically

Basically?

Would these work on a 2009 land cruiser invincible

Good summary, have you looked at the stedi lights that swap out the factory fog lights ? I wonder how good they are.

How much brighter would you say these bulbs were compared to original for the headlights? Are they still working well?

Do you get any radio interference with these headlights?

Great Help, thanks. Is there any mod required for the rear air con vent on the left side of the drawers?

EXCELLENT Mate. Thank you

Hey mate, just wondering if you had hyper flash on your indicators from changing the headlights to LED?

Thanks mate great video

Brilliant saved me a headache or two 👌👏🤙👍

Great video, mate. You mentioned that you wanted to attach your awning brackets underneath. Is it possible? I don't see where there's space.

Steel or aluminum?

Hi, Great video, just finished installing Stedi LED's to reverse, number plate, interior map, and front door lights to my 2015 pre upodate Sahara. Your video explained it all perfectly. Question!! Do you have a video on changing out the 2 lights that are a part of the roof mounted TV monitor? Or give me a hint as to how to do it?? Also the 4 doors have lights at the bottome of the trim, any hints on getting into them to change out the globes?? Thanks in Advance.

Basically...... Bulb fit.

Great video! Do you have a link to the lights you got from eBay please? Stedi are still out of stock Cheers

Hi, Can you let me know if the parts used in this video are RFH1045 (2) and 200FK? Anything else used?

How hot do the heat sinks get? Just concerned of being too hot next to wiring under the bonnet.

Thanks for the vid, ordering a set for my Fortuner. Congrats on the bub 👍

Hi Shaun, really appreciate the video and everything worked a treat - smooth job all round following basically what you have shown.

hey mate. what did that set of draws cost. thanks

Great video. Was trying to find an installation video for ‘genuine’ Toyota weathershields to do it myself. Have more confidence now installing on my Prado which would be similar to your land cruiser.

Man I’ve wasted time on this video. Why would you not record the results!? Before and after type of thing. Or maybe even other LED comparisons?

Great vid. Really enjoyed it and learned a lot. Keep doing your stuff.

🇦🇺🇦🇺🇦🇺👍👍👍

Would it still fit inside the garage. Is this gonna be taller than the oem rack?

Basically a very helpful vlog, basically I will buy a set. Thanks for basically doing this your basically awesome.😁

Any idea if one drawer would allow for one half of the third row seat to still fold up and remain functional? I need one seat to still be useable, three kids.