Видео

Amazon has the handle/cable but it shows 37 different sizes. How did you know what size to order without taking it off and measuring it first?

T8 fit like a glove and worked it right out! Thanks. Always used the heat and cuss method before .cheers

Small drill bit, heat the bit and insert it into the plastic plug, leave the bit in, let it cool and pull it out with pliers

Can I try this on a 2000 ford expedition?

Great Video Jason! Thanks

I have a c4500 duramax and all I have to do is prime it. It will purge the air out. I just keep hitting the primer until it starts to get hard to push down. And it starts right up. No need to open bleeder valve on that model anyway. Not sure if they are all like that or not. But mine's an lly.

question i’m ringing my up now so my positive short wire is going from winder motor to switch then the then what do I need positive to battery to what and negative off battery to what? if you could help i’d appreciate it

Cheers great idea. 😊

That’s genius. Thank you for this

This was exactly the video I was looking for. I planted a mint plant out front in the communal Decorative garden area. I want it to replace all the weeds that always grow there and also always have some fresh mint available, my neighbours can have some too! When I try to grow mint in pots, it thrives then dies, it dies in too much water, it dies with too little water. I give up. i'm going to try natural soil, so I've planted my plant and it's doing well and I have cleaned the area around it and I noticed these little plants coming up. Are they Mint plants or the old weed plants Coming back that were there before. This is the answer: They are mint!

Note to anyone watching this video: Don't cheap-out on your blasting medium. Of all the things in the world to skimp on or try to get around, just buy the good stuff and save yourself the hassle of trying to make something that isn't made for this work.

got a 99 7.3.. just acquired the truck abandoned. been sitting few years. mouse chewed glow plug wires at relay. and the icp wires. fixed wires and a new icp. it fires up with a misfire it seems. has a 10 switch tuner chip that makes a difference for a sec then back to same. have not driven truck bcs its missing still. I found a quarter on passenger side. ill ck driver side next time I get a minute to pull driver valve cover. thanks for tips. thinking of unhooking the tuner chip. can they go bad and cause a misfire?

Good idea bud

So I could technically put this in a closed pot in the ground and just leave a lip over top and it would grow contained and fine

Have injector 2 & 8 code in IDM 2 & 8 Failed Buzz test & contribution , replaced IDM, still runs the same Truck has 92k & also never injectors Shop says needs injectors, I don’t think so Believe this may be this fix Thank you

I have a car that I have in storage, right now and I know it doesn't have this feature, what would be the best way to stop fuel if you don't have this feature?

Reclaiming

I've been on You Tube since it started and this is one of the best done, well thought out and helpful videos I've seen. I just bought a recliner with this type of pull and I suspect it is the recliners Achilles heel. Now I see how it is replaceable. Thank you for your hard work in putting this much needed video together.

You had the wrong diaphragm on the carburetor.

I have 2008 F90 4 stroke yamaha. Need the link for aftermarket trim motor.

Thank you very helpful

Good morning, I love the video, if a trim stops can it be serviced or you need to get a new one completely

Very helpful! Thank you.

How do you replace the cable when the handle is intact but the clip at the far end has broken?

I have the sane style D-Pull but was wondering why it’s so hard to pull to open up the leg rest? I have lub the open mechanism on all moving parts with 3n1 oil. No squeaks etc, but still hard to pull the ring? Any help

EPA somehow believes small string trimmers create pollution, meanwhile commercial jets belch jet fuel into the atmosphere and tens of thousands of rubber tires are being burned in Cambodia.

How come mine does not have any screw for what your doing, I have two rams that work my trim, on my mercury 69 ob , there is no screw to lower it

One point no-one mentioned is CARB (California Air Resource Board) has mandated Zero Emission on small equipment requiring all small engines be replaced with battery packs. 2-Cycle has been banned in Calif for many years and now everything under 50HP is outlawed. How long until all states follow their master plan? I saw a Ryobi push mower for 900$ in another video, the replacement battery packs (2) were 219 each.

Very Informative Thanks

Good video; thanks for posting.

Just grab a drill bit that will fit snugly into the brass plug , the end of the drill bit that fits in the drill ,, NOT the cutting end , after getting a bit that fits snugly into the brass just pop it out sideways !

any tips for hanging the vacuum hose over the pool wall?

Thanks Jason very helpful video.

Thanks for the pictures of the pressure release, I released the pressure motor went down now it works great. Thanks again 👍

E-P-A…….extreme-people-aggregation !!!!

Hey I'm doing some repairs to a free recliner like this too.👍

Jason, thank you. What if it does not fire up asap? I just changed the wif sensory (fuel filter was changed about 6mo ago) and it will not turnover. I primed until it filled and no bubbles surfaced. TIA for any help!

Thanks for saving a lot of money. Thanks again

The brass piece is removable if you disassemble the carb and use a good pair of pliers , like Knipex pliers to remove the plug. I think I might invest in the Echo 2.5mm tool. My problem is the compression and the carburetor itself. Compression is 88 psi. I ordered a new carb so we will see if that's the issue or is it the compression. Spark arrestor and port are very clean. Thanks for the video. I have owned Echo for years with the High Low and Idle screws that are very visible and I wish they would have never changed to these , so called , fixed carburetors

Computer ground strap works good too.

Well that helps a bunch. My nipples hurt from all the screw shocks.

Where on Amazon you got the part from? My son broke the lever on my sectional

Nice one

How did you make that pressure tester..

Thank you !!!!!

Few 100?

Lame ass video of nothing. Won’t get that time back

I think these were added so they could be sold in California.

Great idea... I have an older retired Crown V Interceptor. 200K and she runs great except for noise on start up. I've been doing the engine start like this for over a year and it's really does work. No noise on fire up anymore. My attitude is, build up the oil pressure quickly with no load on engine. There is residual oil already in the engine from driving it the previous day. Still running good. Thanks again.