Видео

great video sir! 👍

Beautiful demonstration, thank you for sharing.👍

Good work bro, but I want to ask a question, what are the numbers and guage of the receiver coil, are they the same as the transmitter?

Hi , thanks that you are show the new method for accumulate this kind of amplification, this system requires high voltage output with LC resonant circuit, i also.experiment this circuit from the past years , now i have very moderate tricks with this kind of circuit, and the output witch i get is now stable

Ótimo vídeo, bem explicado! No entanto, há um detalhe importante a ser considerado: o projeto que você montou não é exatamente o sistema de transmissão e recepção de eletricidade sem fio desenvolvido por Nikola Tesla. Se você ler as patentes dele, verá que Tesla deixou claro que existem dois tipos de transmissão: a transmissão por radiofrequência (RF), que é o que você está fazendo nesse vídeo, e a transmissão por campo elétrico. Tesla afirma explicitamente que seu sistema não transmite eletricidade via ondas hertzianas, mas sim via campo elétrico em altas altitudes, em um ar rarefeito. Nesse ponto, ele cita o trabalho de William Crookes. Infelizmente, poucas pessoas tentaram replicar o trabalho de Tesla da forma como ele realmente o fez. É importante destacar a diferença entre esses dois conceitos para evitar confusões e garantir que o trabalho de Tesla seja representado de forma precisa.

Thanks for sharing, but power consumption is way too high is there no way to bring it down and race the output

Can you make another circuit for 2024

Can radiant energy pass THROUGH a spark gap and on through series circuit , if it's in a small vacuum chamber? There is way less dissipation into ambient air, and the energy may be useful downstream. In 2005-2008, A sealed extreme high efficient vacuum dual coils relay , as originally for a electrical 60 cycles signals pole box, was used with engine experiments, to generate more efficient hydrogen gas from water. The engines would run with spark plug electrolysis, but only with the special relays applied to pass both high voltage and 7amps current! (not used for a relay purpose, but for contacts, diodes and inductors) I recently built one with Carlon sealable 4" box, vacuum gauge, valve, and Tesla spark gap with magnets, diodes, cap and hand vacuum pumper tool. Not tested yet. See one of Nathren's / S1R engines running,- S1R9A9M9 You tube videos 1+2. It was started with battery. Battery disconnected. Engine ran on the 12 magnet alternator , - self running sustained with 10amp draw. The 4 technicians called them "The Magic Relays".

@gsav2504 HI how are you i need to talk with you about some project

It'll probably be better to refer to that as single wire transfer... Since you could probably put some kind of shielding in between the antennas and it was still get a signal.... Can't always count that the ground is conductive enough to be usable as that wire... Nevada for instance has terrible conductivity in the ground

Reminds me a little of the Don Smith device. What if you add a slight resistance to the L2 ground?

Can't you add a few more receiver coils? The input might go up slightly, but no where near proportionate to the output, I would think?

can you make a Cold Bath?

Excellent explanation, thank you so much 👍😀

Would you be willing to post a parts build list and circuit diagram online so we can try to replicate this experiment? Thank you!

Not overunity, just a joule thief.

Don't harm you because of frequency, not because of "cold" electricity.

What a great demonstration of wireless power transfer system . Thank you for sharing your testing and circuit diagrams .

Tesla's wireless power did not utilise Herts it was measured in volts per sec.

caballero buenas noches, ante todo muchas gracias por compartir sus conocimientos, hice este circuito varias veces y no me da nada, lo he revisado y revisado y nada, podria darme alguna clave, muchas gracias

Thanks for the nice video :) Is there a surplus of energy in the system like a gain, like a over unity thing going on when the receiver LC is turned of? Can you expand on that please :) What is going on? Thanks

Amazing!

....the transistor in the circuit diagram didn't exist for another 50 years after 1898.....

Dear friend I try it with 547 transistor but it does not work may you make an other video explaining how to

If only the Inverse Square Law wasn't a thing. ;)

woooowwwwwwwwww I think I found a solution to my problem🤨🤨🤨🤨🤨🤨

Very cool!

Que valvula usaste ????? 12AX7 ??

Es increible como la frecuencia se mantiene estable , excelente proyecto !!!

С розетки наврдящее электричество эдс т.к земля ещё вторая присутствует образуется ток разность потенциалов

High voltage + filament vacuum bulb equals x-rays. From all my research my understanding is if you are going to do this be sure that the filament is broken and cannot boil off electrons.

why do people not use AI for vocals?

Excellent demonstration of the concept. Слава Україні!

Muito obrigado Amigo👏👏👏👏🇨🇨🇨🇨👍👍

I like your setup for this. Great idea to use those variable capacitors. I wonder if you could extend the receiving distance. It's a very good demonstration. 👌👍👍👍

Здравствуйте G Sav, Just for understanding, If you make the ground, same at the Receiver and the Transmitter. The distance is not important it can go as high as 15 m or maybe even higher. But you showed us at 09:19 , grounds are different and the distance is just 30 cm. So the main idea is, resonate the frequency and same grounds. Did I understand it correctly sir. Lastly do you have something in your mind to improve the distance without same ground. Большое Спасибо

Awesome videos on your channels. Thanks for sharing? Really good how you explain it with the schematics. Can you name me the type of your variable capacitor? Thank you.

I don't know anything about electricity. But I can see the wire you call "ground" is connecting both sides of the setup. For me, that makes it seem like it's not wireless, but is just going through the wire? Why not try to connect to the real ground to see if it still works? Otherwise, maybe the power transmission you are experiencing is just going through the cable? Also, how do you get the signal to 16 MHz? What part of the circuit generates this oscillation? Is it just a function of the design of the coils? Are the coils free metal or are they coated with an insulator?

the awesomeness that he shares the schematics.

Nice! If you replace the "antenna" to just alloy foil, working as well! :) Foil ball.

Very nice thanks

Excellent work, many thanks for sharing ❤

Super cool!! and too think Tesla was doing this 100 years ago....The powers that be certainly curtailed electrical research for a very long time. keep up the great work...

Smells like BS

Supercapacitors battery

Great video, thank you.

The spark gap should be in parallel and the capacitor in series, one of the reasons is that it extends the oscillations and increases the economy, furthermore this is meant to be a reactive power producer circuit that occurs from the free oscillations bouncing around in the circuit at its resonant frequency per spark discharge, reactive power cannot be tapped directly since it kills the oscillations so another trick is required. Tesla's tech is meant to go beyond energy, reactive power is where he was headed into and the hairpin circuit is an example of such a device, but tapping it directly is not how it's meant to be used.

Hi, nice demonstration. I do several own simlar experiments and I'm an electrical engineer. Your measurement should be enhanced zu real and reactive power measurement. Can you please use your oszi with math function. U×I and look. May your oszi has Powermeasurement like on rigol mso series?

More Junglebunny gibberish. Cannot understand a word. 👳🏾🙉

Hello G, wondering what is the propose of the device. you trying to achieve more output then input and improve efficiency?