Видео

Thanks a lot..

I use colour indicating silica beads in small, round, perforated tin screw cap containers. Throw two of the tins in with the filament, drop in a small humidistat, suck out the extra air, and I'm good to go. As soon as the humidistat reads anything above 15%, the tins and the filament go into my dehydrator. Been running like that for a while and it works well.

I like it.. gonna have to try it

How did you manage to get 70 cut sheets from the foam quantity listed in your supplies needed if you cut them in half? I understand you said you salvaged some from under your pool, but why not give an accurate “supplies needed”? when it’s all said and done, that a $120-$130 target.

I stopped using silica a while ago. It's ok for long term storage but it really doesn't have the oomph needed to pull enough moisture. I prefer calcium chloride. I get a 2 pack of desiccants from the dollar store for $3 and each one lasts about 6 months. I have put a new spool inside an airtight container with the calcium chloride, put the lid on and just left it at room temp for a few days. NOTICEABLY drier with zero electricity needed. Granted if you employ a little heat things dry up even better. I'm happy to wait for filament to dry and I do not need it available immediately. The best part is that once the calcium chloride fully dissolves and stops working I can drain the desiccant packs into a pyrex dish and pop it into the oven when I cook. It'll dry out to a crust which I can then put back into the pack and reuse.

somehow i'm unable to buy this stuff where i'm from. could only find a single seller on Amazon, selling it for 200 bucks per 3kg 🙄

Thanks for this video. Great tip regarding use of filament dryers directly feeding the printer. Also, thanks for the heads-up about not really needing an enclosure. I'm leaning toward a Bambu A1, and your Amazon solution means I don't need to shell out the big bucks for an enclosed P1S, although I might buy a $50 grow tent to replace the cardboard someday lol. Oh, one other thing, in case you ever make a follow-up video, Nylon is a brand name, the actual material is Polyamide or PA, IIRC, so you might get more RUclips search hits if you put "PA/Nylon" in your title next time. Keep up the great work!

I saw that you used those orange shims for the 1/8" gaps between the framing and the door. Is this what you then used to set the depth of your hinges?

That eSun kit is absolutely great. I have the same one.

Ten seconds into this video and you've got me cracking up, lol.

Case hard nails followed by tapco s or Dynabolts per code

Should have both tools honestly

Thank you for sharing this information .Also I came across this video about cancer causing by MDF . ruclips.net/video/7kMNCWrnEfs/видео.htmlsi=-VUP9FLz3XZcP-xJ

is this more toxic than silica gel beads?

Thought it would be cool in the freezer no?

don't touch your brake light bulbs, use a paper towel. That is a manufacturer's recommendation as the sweat and sebaceous materials on your fingers degrades the bulbs. Use a paper towel or clean rag. what about the rotational sensors? Aren't they failure prone?

great build but you have the sizes wrong as in your plans you have 2x 1100 when it should be1x 1100 then 1x 1082 or you will have a side that slopes 18 ml out as orcording to your build

The other issue is that MDF dulls blades and bits FAST. Penny smart and pound foolish, imho. Better economy can be had by selecting framing lumber to shape with a table saw and router imho.

You could have just tied a bag of mesh and been done.

are you selling this coil cutter devise

Try a larger tire such as a used truck tire or fat machinery tire for rocks. If you can find a logger, their tires are super wide and not terribly large in diameter.

Ok, this tool look game changer. This is so cool to see how you’ve created it ! I definitely will never be able to do it myself, but if someone what to do it for me, I could buy it 😍

What about using chip foam instead of clothes?

one of the best 3D printing videos ever for those in humid climates. Thanks

Man what i could do if i had my own wood shop..

excellent guidance thank you. 5/16 = 7.3975 mm, i apply bulb grease, clean all lamps with alcohol and test before reinstalling assembly.

Thank yo.

Hi . Great video.. how do I get the plans. What is the approx cost to build this paint booth? Thanks!

Looks great. I think you could make a few spacer pieces instead of all the internal measuring and marking to make it easier and more foolproof.

You can always re-true your squares - it is simple, that's the real story. iGaging is "okay." I own a few, plus a couple Starrett squares. When buying iGaging, do the research - not all their squares have accuracy claims, and at the resellers, the claims run from, .002 to .005. so check it out. As far as boxes? Starrett does it right, no unnecessary contributions to the landfill!!! WTF

I like the ones that auto lock, and you push the button for them to retract.

Just don't mop the floors.

Somewhat awkward framing of the first shot with the two of you. 😅

very nice project, it fits all sizes!!

this may be great with my crossbow

The Wire taught me everything I need to know about power actuated nailers.

I personally would solder mesh with soldering iron and a few tin drops. Nevertheless, thank you for informing about activated alumina. Subscribed + new to 3d printing

I always wondered why 2x4 strips arent added to the back side to prevent the wobble so that its braced. It would be easy and cheap to do.

I don't know. If you'll see this comment or not, but when you said brake lights being out, does that mean the third brake light also cause mine's out and my cruise doesn't work LO😅

I ordered the layout square set - the larger 12 inch square was off by over 1/8 of an inch. Totally unbelievable after paying 135 CAD for the set. Treid calling dealing with thier customer service but they spoke very poor English/Chinese. I wouldn't recomend this product or company

You have to already have a flat surface to build a flat surface. Well,if I had a flat surface, I would not need another flat surface.

Every consider printing in PC-CF? I print spool centers, AMS trays, and AMS inserts. This way I dry it in a convection oven at 115-120 ºC for about 4 hours container and all. Fill with your choice of desiccant.

Just made one of these and have one suggestion. The uprights that hold the connectors for the bearings are far too thin and break really easily. I fixed it by super gluing a popsicle stick to the outside.

abs, a/c , cruise control fuse kept blowing. It was the 7 prong trailer connection just wanted to share, I haven't seen no videos out there showing that it was the seven prong connector. it took me a few days to figure out hope this save somebody some time.

This might be a little bit better than Fillament Bunker V3 because of those side horns to ensure the roll doesn't slip off

I found 2 spools one from IC3D and Jessie's Premium (both from printed solids) that do not fit inside of this. The spools are about 20.5 cm (~8 inches) in diameter. The width of these spool seems to be the biggest problem, they are 7 cm (~ 2.75 inches). All the rest of the spools are from Bambu labs and they print and store in there perfectly. Thank you for the tutorial and the files. Do you have one for larger spools?

LOL the amazon box, neat trick

I've been looking for something like this for 4 years! It's perfect! I have questions about purchasing the blueprints and materials etc. Can I email/DM you with some questions??

I like this design because you can use any type of cheap boards from any local store. You could use even polystyrene that should be much cheaper than what you used in this video.

Isn't it heavy? What if you use bean bags filler? would that be enough for stopping ..maybe with a few pieces of cardboard in between. I did not see the price for it. I think this form of target only works in you area. For me the foam boards are quite expensive. It much cheaper to actually buy a foam target from an archery shop.