Видео

You know the button that's with the power switch. If you press that as you turn on the power it will beep that way

Mine was doing this and I just switched the wires around

💯..🔥

My program card just flashes both rows of lights in a running sequence from left to right and won't stop I don't know what the hell it's problem is

​@tenrc7779 You need the programming card with 10, 16 or 17 options, the little black boxes with 10 leds and buttons that say iten and value and ok and reset. Apparently these escs are "smarter" than the old ones, all depends on what microcontroller the esc uses to control everything.

Adjust your trim. And your transmitter shouldnt be so close to the reciever

Go with surpass hobby. Still cheap but better quality. Just my opinion.

I love the algorithm

Was wandering if you could help me, i purchased a Goolrc 35 amp esc when it runs its fine but it cuts out then comes back on again. Any ideas.

I have the same issue! The problem is that the card is apparently way too old for the newer escs, it sucks, you need a 1 to 4 not a 1 to 18 esc( whatever that means) i just heard about it when I asked for help!

The Bash&Collision Kit🦾#ebayseller#findusthere

Did you have to program the esc

This is actually a common problem with most but especially this transmitter, which is a simple rebrand BTW. Especially with this one because it really has exposed throttle trim knob. So you knock it with your fingers, knock it in the box, and knock it in the backpack. Multiple cheap esc's hate throttle input at setup. I'm guessing more expensive ones have software, that accepts it at neutral, which may mess your exp up, but at least you won't instantly assume it's broken. But not those cheap ones, and it's sad, cause they get bad rep+when beginner gets RC with better radio included, there will be throttle trim knob on it... you know where I'm going

Nice video bud that moves some an off road to love it

Is it the same thing because mine beep slowly

That card is the wrong one. Get the right card to program and you need to do the calibration first.

great timing ;)

Mine does the exact same thing

Mine did the same thing I had the water turned around backwards in the transmitter

Adjust throttle trim

Thanks so much omg I have been trying to make this thing work for hours

I have a goolrc esc and everytime I turn it on it goes perfectly fine then after a couple seconds it slows down until I can't go forward anymore can someone help me

Mine will just chug..... I got it to work once but it keeps going back to the chugging.

Maybe try the card I used in my recent video. That esc looks similar to mine too. Sounds like a bad esc to me tho

I had the same problem and everything started working when I turned the controller off and on

I had the same thing happen and all I did was set the throttle trim to 0 and then it was just fine. I don’t know about the card though.

my programming card just has the work state light blinking and I cannot do anything

A vídeo is on my channel to show you how to fix it

I have ordered a programming box from Amazon I'll try it out and let you know

I got the same problem with one of my cars and even a car to where the ESC was not beeping like that and the programming card would not work..

Thank you so much

I sirr can i know how to fix this i cant use programme card same like u.. The blue light cant stop

I have the same issue with a 35A ESC and that card.

how much runtime do you get out of this?

Mine won’t even beep. I think I got a dud

Mine is not even doing the fast beep help meee

It didn't work rip

Thank you so much for this. I was having the same issue with a hobbyfans esc. 👍🏼

U need more power i had a 3s 2200mah 30c n it would cut out alot so i went to a 4s 8000mah 120c

Did u get a new card or did it still not work

Is the painted lid a redcat blackout body?

Any solution about it?? I have the same problem

I did solve the problem, but the ESC still will not work with the programming card.