Видео

Well, the point is to get it out… as I said, “one of the many ways to do that “… 2 days later I received the special socket from McGard 😜… 🙏🏻 for comment ! Good roads to have, I wish you !

Funny you mention that. I changed my oil twice and per Mazda it states (4.8 liters) 5.1 quarts with filter change. Both time 5 quarts only puts it 1/3 to 1/2 between the holes on dipstick. 5.5 quarts brings it to the top. BTW, I am using Mobil 1 5w-30 EP with a Mobil 1 M-208A filter which is what Mobil 1 suggests on their website.

🙏 for comment & advice ! lately i read some bad words about these engines and I decided to be more careful, to replace the engine oil every 5.000 km instead of 10.000 as before; we don't use a lot the car, after more than 5 years we are on 50.000 km ... now the brakes are finished; just received the parts, bought brake fluid and I intend to make some more preventive maintenance on the car ... thanks again and good roads to have, I wish you !

I will not melt. I will slide easily when you are going to tighten it up. Anyway, it’s a good idea to add a little bit of oil on the o-ring. 🙏🏻🙏🏻🙏🏻

🙏🏻 for comment. Glad was useful !

🙏🏻 for the comment ! Glad to be helpful ! 😏 only if you don’t work you don’t hurt 🫣 ! See you soon around ! God bless you ! Good roads to have, I wish you !

❤ Thanks for your comment ! I’m glad my hard work helped you ! It’s not easy to record when working… After that I have to edit the videos and now I’m struggling to learn the new software i bought and it’s not always easy! You don’t know how many times I was to the point to stop making videos for my channel and cancel it because involve a lot of time and work and sometimes I get just bad comments… Good roads to have, I wish you !

Hi ! Thanks 🙏🏻 for your comment ! After that job, few months I had no problems. But the car started again to make noise when braking. I went back to my friend and now I get different error codes. So, I bought the bearing with the sensor and I replaced it. Again, few months everything was fine until the car started to sound weird, as before… The winter passed and now it’s quiet again but I don’t know for how long ! 🤪 Hope to stop for good ! Good roads to have, i wish you !

🙏🏻 for comments ! I did that at the beginning of my channel. Not anymore… you’ll see on the newer videos. 🙏🏻

hey ! thanks for comment ! I used some antiseize paste for the SCREWS (min 25:00) ! ONLY ! You can see in the movie the bushings are DRY ... min 23:31 I didn't use any kind of oil or grease on them ! the sway bar became black because i touched it many times not because I used some oil/grease on; those bushings have a slot, so it is not hard to put them back ... the music ... it is free from youtube 😜... meantime I do not use any kind of music when I do movies about jobs like that ... just check later movies if interested ... last year i tried to do the same job on the Yaris ... ON THAT IS A NIGHTMARE to work; much worst than on Hyundai !!! I wasn't able to release the frame ! much tighter space to work on ! so, I'll wait until the link-bars will be finished and I'll try again because I bought some tools who should help me to work a little easier on that job ! before to bring home that Toyota, I was so confident on that company ... and now, I changed - a lot - my point of view ! good roads to have, I wish you !

they have to be very well tightened ! if you don't use anti seize paste, you can torque them at the specs; if you add some paste, is better to torque them a little more, let say a 10% value ... on those screws is 1/4 of full weight of that car, so it's a safety concern ... thank you for comment ! good roads to have, i wish you !

🙏

Hi ! 🙏🏻 for coment & ideas ! I still have the original hub and maybe some time I’ll try to do as you suggested ! As I’m not an English born person I don’t understand the meaning of the expression “You left getting it out”… The point is my car still has errors on the dashboard … they appear about 5 months after the replacement of the hub and cable. I saw a friend who had a tester and now he found different codes… The car is working fine but the ABS it’s out of order… unfortunately. Thanks again and best wishes to you !

@@mipmixchannel Sorry, I meant you did not show getting the hub assembly out of the axle. In the north they rust.

You are welcome 🙏🏻 ! Glad to see was helping you out !

those ones are sliding and could be turned a little bit; there is plastic all around and you have to push/pull a little bit ... min 0:15 and after, you can see I pulled out the tray; it is flexible and the clips are coming out; you can play in slow motion and you'll see better what I am doing there; wasn't easy to keep fix the camera and filming alone ... hope you are gonna fix it; good roads to have, I wish you !

Hi ! Thanks for commenting ! My car is 2.000 cc gas engine… here we have only this engine available. I have a manual transmission with 5 speed… The 1.6 L engine is used in the Accent model only… I’m having in summer an average of 8.5 L / 100 km and during the winter 9.5 L / 100 km. In summer I use a lot air conditioning… in winter 🥶 I start the engine often before to go somewhere to get it warm… About 50-60 % driving highway and the balance city… The car 🚙 has a fuel tank of 50-55 litres…

@@mipmixchannel Thank you very much

hi, i can't tell you big deal ... if you can send me some pictures on my fb messenger ... what I would do ... i will try to go at a parts store and try to change the hubs for hybrid with those you really need ... or sell them on market place or other platform and buy the good ones ... you can do another tric: cut the wires, on boths (old and new) and connect them color by color ... and you take off the plugs you need and "adapt" to your new prius C hubs ... it's a bit risky but it COULD work ... thank you for comment, succes and a happy new year !

@@mipmixchannel yeah I was thinking about the cable cutting option. Since I couldn't sell these..

🙏🏻 You are welcome! Success! God bless you!

Hi! From a local parts shopping centre They told me it’s a good quality I put it on only few months ago… I don’t know if it’s a good deal or a bad one…

hey ! thanks for comment ! hope it helped you ! wish you'll finish asap and enjoy ! with that work you saved minimum 1 000 $ ... only for labour ! best wishes !

indeed, suspensions are the same ... if you have someone to help it will be easier; as you saw in my video, I was alone, the night came over, I was in hurry to finish ... the strut assembly is moving, but you have to pull strong with a hand, and to find out the right position with the other one ... and in plus of all, I do not have a lift to work up ... so, a weird position; so, my advice is to have some help from a friend just tu help you to fix the screw ... one of you pulling the strut/brake assembly and the other one to introduce the screw ... after that, you can work alone ... wish you success !

@@mipmixchannel 54541-2H000 is the part which connects the control arm to the ball joint. it's screwed to the control arm by 3 bolts. Don't you think, that one way to avoid the above mentioned problem is to take out this part, screw the ball joint into it and then screw these 2 parts to the control arm? Did you maybe try this?

Thanks for your comment! It seems you are french. I could write in French… You have the same noise and clunky when you get over bumpy roads as when the link bars are used/broken. If you already replaced the link bars and the noise remains that mean those bushings from stabilizing bars are finished too. It happened to my cars from time to time… so, I checked again all suspension and nothing wrong! I tried to see if those bushings are ok but couldn’t figured out… you need to lift the car on both side to see. So I saw the bushings are not expensive at all, I decide to buy them and change them. After, no more bad noises inside the car. Hope this helped you out! Good roads to have I wish you!

Hi! Thanks for your comment! That car is not mine. The owner bought the oil filter from a Mazda dealer. I’ll let him know and next time probably will be replaced with the one you suggested. We’re going to make a “test” and I’ll let you know about our impressions about that. Thanks 🙏🏻 again and good roads to have I wish you!

That is not accurate. PY8W-14-302 is absolutely a correct filter for the 2.5T. It's what comes installed from the factory. They are hard to find in the US now though. 1WPY-14-302 superseded PY8W-14-302 in the US market and is made by Denso in Thailand. There is also PY8W-14-302-MV which is made in Mexico and while it's technically a fit it should be avoided due to quality issues.

Please check the other diy with the wheel bearing. I suggest you to change that before replacing the cable/connector. In my case It didn’t worked until I replaced the whole wheel bearing but be careful when you order it to be sure it is coming with the ABS Sensor ! Please watch the last movie i posted. Thanks 🙏🏻!

Hi ! I could be blocked even because of long time sitting there unchanged … you have to try turning left or right … if not ok if you try towards right, try on left. Sometimes you have to force it a little… Hope you can handle it… Try to reply slow the movie on the part where I took it out to see how I did it … Please let me know if you successfully have it. 🙏🏻

@@mipmixchannel

Thank you so much for this video and helpful hints, I also sprayed some silicone spray on the bulb, waited about 15 minutes and was able to extract the bulb by slowing wiggling it from side to side. Your information was very concise and helped solve issue of extracting bulb.

I am working on… After I did it I found i didn’t fix my problem… I made research, bought the right assembly, replaced the hub which has the ABS sensor pressed in … Today or tomorrow I’ll put online with all details… about this “odyssey” … It’s weird, I have that problem on a Toyota!!! On the Hyundai Elantra I have 274.000 km and never had troubles like this !!! Sorry…

Dude … mechanic can be a bunch of shit. It’s always about replacing what looks bad first and upgrading. Plus the wires are not pricey so it’s not that bad to replace also

hi, and thanks for your comment ! this is the part I bought ... "Rear ABS Wheel Speed Sensor Connector" even for me it was a bit strange but if they name it that way ... a piece o wire in fact ... 🥸 www.rockauto.com/en/moreinfo.php?pk=5408913&cc=1502640&pt=762&jsn=1 I did't find the picture with the code I had ... but I had 3 lights on the dashboard (parking brake + abs + traction control) and now I have no one ... seem it is working well .. 😎

Boo hoo

😂

🤓 with some patience you can do it! Elantra is now @270.000 km … working well… I have to replace the alternator now… not charging anymore the battery… I need to find some time and good weathers to do it. Thanks for your comment! Good roads to have I wish you!

I have one with 215k km's, 2009. It has been fairly reliable, and cheap to fix when it does break. When I bought it it needed the timing belt and harmonic balancer done. Timing belt is a typical thing for any 2000's car, needing a new harmonic balancer already was a little unreliable though. Since then my only issue was that the door window switches stopped working, they are a bad design. Each switch was about $50 Canadian and took only 2 hours or so to replace all of them. Otherwise I have had no issues, with the 2.0 litre gas engine and 5 speed manual I get 6.4 L/100KM on the highway, city mileage is not amazing though, around 9.5 L / 100KM. It is the best car I've owned, very happy with it.

Hi ! Thanks for your comment! Mobil1 is a very good oil. I hear 👂 Toyota brand oil is Mobil1 … maybe Mazda too ! We are in “French” 🇨🇦 … Province of Quebec… Change your oil at max 10.000 km / 6.000 miles and your engine will run long time! Good roads to have I wish you! 😎🙏🏻

@@mipmixchannel I have been to Montreal before. Beautiful city. ✌️

@@Matys1975 indeed…🙏🏻👍🏻

I just traded my 2015 Mazda 6 with 144,000 miles in for a new CX30. I ran Castrol Edge 0W-20 full synthetic the entire time I had it. Won't use anything else.

@@mhepping me neither ... only fully synthetic ... the owner of the Mazda, too, only synthetic oil, max 10.000 km / 6.000 miles ...

Thanks for your comment! If you watch my videos about the oil change, you will see I change the oil at maximum 10.000 km (-6.200 miles)! Always synthetic oil !!! Here in winter is cold and in summer warm and humid ! When I bought the car I changed the oil first time at 2.000 km and after at 10.000, and so on from 10 to 10 thousand… I did the same with our Elantra Touring and she is working well even now after 268.500 km ( -167.000 miles ) … This is the way I proceed… Good roads to have I wish you!

Hey ! Good roads to have, i wish you !

Thanks for your comment! Indeed a “ noble “ dog 🐕 💙💛❤️

Thanks for your comment! SE R is with 2.5 L engine, more power there ! And few more options… I bought mine especially for my wife for a daily drive purpose. Cheap on gasoline ⛽️ and maintenance… “Stela” is still on roads… the owner is satisfied with. About 150-160 thousand km … Good roads!

I drive mine every day 160,000 mi. 27 mpg

I've been driving my 2004 for 20 years, love that car

Hi, thanks for your comment! I never tried that trick! So I don’t know if will be a long time solution. And on Santa Fe I didn’t work yet. But the principle is the same for that assembly. Maybe you can find out on RUclips a DiY with that. Sorry I can’t help you more! Good roads to have, I wish you!

you're welcomed ! hope was usefull ... thank for your comment !

Thanks for your comment! The car is still on the road….. i know the owner.

It’s the same model and engine? You have to use 5W30 … The filter… you have to check with your local dealer because there are 2 engines and I understand that each one has a different type of filter

Hello my neighbour ... from Canada now ... I was born in Romania ... 😜 Thank you for comment ! If you like, please subscribe ... If you read in description, I gave some tips to help ... hope it will be useful. Good roads !

🙏glad you like it ! Thanks for comment !

Synthetic engine oil always !!! I heard in Europe Castrol is not a good oil… better one is Mobile 1 … Here in Canada i use Castrol for more than 15 years and thanks Lord seems to be ok …

6 liters / as they specify into the book… always synthetic oil/ I replace it each 10.000 km !!!

@@mipmixchannel thank you so much very appreciated God bless you