Видео

보기에는 할수 있을거 같은데 브레이크다 보니 정비소로

제네시스, 더k9 람다2 3.8엔진은 저보다 더 지랄맞게 되어있어요... 2번 분리하면 거의 망가짐 ㅠㅠ

May I ask which wireless OBD did you use ?

Nice job

작키가 좋네요

Hey Chris I got a quick question, what if I purchase the bearing without the sensor and then install My old sensor which is good, how can I know how to align it properly?

와 금손이십니다

Great video - thank you! I replaced with one called RLB-Hilon from amazon for $13. Solved problem of the 3 warning lights on dash indicating ABS, stability ctl and downhill control. Remove tire, disconnect old sensor by removing retaining clip, remove caliper, drop strut that blocks caliper bracket bolt (because getting a box wrench into that spot is tricky), remove caliper bracket, rotor, wheel bearing assembly, then pry old sensor out with knife or very thin screwdriver. Replace, assemble in reverse. All good! Note the sensor for the front is very different and for AWD vehicles the rear sensors are also different.

I changed the two in the back. The millero still doesn't work on mine. And the lights don't turn off. I haven Hyundai Santa Fe 2014

Thanks for the very informative video. A friend of mine has a scanner that also checks for ABS codes. The right rear sensor was sending signal that the car was traveling 170 MPH while we were sitting with the car in P. It looks like a simple enough job, I wonder how much more the dealer wants for the part, it's cheap enough on Amazon.

혹시 퓨즈박스쪽에는 그라운드 볼트가 없나요?

와 이분 금손이시다...

ㅎㅎ 하체 작업의 꽃은 고착된 헙베어링이라 할수있지

안녕하세요! 영상 잘 시청했습니다 야매카닉_YAmech님! 현재 벤볼릭 체험단 모집을 하고 있는데 혹시나 희망하신다면 댓글이나 설명란에 메일 기재 부탁드리겠습니다!

금손+자동차지식

와 기술 지기네예...

Very informative video 👍🏼

이야....대단하시네.. 난 그냥 센터 맡길랍니다.

작키 추천 좀 ... 궁금합니다

영상보고.. 수리센터 가야겠다 마음먹었습니다..😂😂

Wow

금손이시네요

Is it possible to remove those bolts by manual wrench instead of electric wrench?

I have a 2012 Santa Fe. Your video was almost exactly on how to change the abs sensor. I was able to to do it and saved $350. Thank you. SN: The 2012 Santa Fe doesn't require an offset wrench because you have enough room to do it with a socket wrench.

Would this be the same for a 2015 Sonata 2.0T?

방법을 알아도 저걸 못해 쫄려서 근데 저걸 성공하시네 대박 ㅋㅋㅋㅋ

Good video, just one correction needed, all you have to do is push the clip in and the plug will release when pulled. I looked up how to change it in Mitchell since I found the sensor separately at one of the parts stores. Mitchell said to remove the front wheel and the back seat. I think that comes from Hyundai. What? Remove the front wheel and rear seat back, that's insane. It still never mentioned how to separate the sensor from the hub. I figured I would have to pull the hub to do it but wanted to see if there was a way to pry it out without removing the whole assembly. Thanks.

Good job

이 작업 공간은 사무실 인가요? 저는 작업할 공간이 없네요

오 👍

Great video and info 💯🤙🏽 thx

What diagnostic app are you using

오오... 개쩐다

알라배마에 계시네요오… 혼자 설치해보려고 했는데.. 🥲 여전히 어려워요오 ㅠㅠㅠㅠ

Thank you! Good information!

Replaced my sensors and lights remained on. My new sensors are reading 20m ohms. Is that right? What should the actual ohm reading be for rear tire sensor? Does it have to be around 240ohm?

2014 Santa Fe. Saved hundreds of dollars for the price of a sensor, offset wrenches, and a Saturday morning. Thank you sir.

똑같은 제품 사서 해보려는데 클리어코트? 이건 준비를 못했는데 생략해도 되나요?

클리어코트 생략해도 되나요?

감사합니다.

Thank you

평화발레오 디스크 주문했는데 디스크면쪽 오일? 미끄럽던데 방청제? 닦아줘야할까요? 그리고 볼트쪽 고착방지제도 꼭 필요한가요?ㅜ

360방 600방 이라 하셨는데 네이버에는 36 60 스펀지사포가 있습니다 어떤것이 맞는지 알려주십시요 좋은하루 보내세요

정말 부럽습니다 똑같은 색깔의 차가 같은 부위에 굵은 상처가 있습니다 범퍼 탈거 안하고 할겁니다 정말 귀한 방송 감사드립니다 자재구입 요령도 알려 주시면 고맙겠습니다 전동드릴은 있으니 필요한 자재 좀 가르쳐주십시요 감사합니다

금손이다 !! ❤

Thanks 👍

색스프레이 뿌리기전에 저 프라이머는 왜하는거에요!!? 클리어코트는 모에요?

Dealer quoted me 450 for one, 700 for both. This video will help me do the job myself. I bought the genuine KIA part (20 bucks! on ebay), and an 8 dollar offset box end 14mm wrench. Thanks for the clear, concise step by step video! BTW ... Auto Zone diagnosed the problem even to which wheel sensor was causing the lights to stay on for..FREE!! Only thing I may do in addition is to put a little silicone caulk at the outer edge of the part before tapping it all the way down. KIA had a service bulletin on this 7 years ago for this car, and it said it will help keep water out which can wreck the sensor.

Very Well Done!! My parking brake pedal (KIA Sorento) goes down about 7 inches. This will help a lot! Thanks!!

Thanks for the electrical specifications.