Видео

Bonjour, j'ai 2 rsat2 mais sans diode, pourquoi mettre le pont rouge puis l'enlever? Merci

Great video. Concise and informative. Thanks for sharing.

What have I done...? This is by far the stupidest system I have ever seen in my life. I thought I had purchased the "real sh*t" (in positive means), but i really understand that I did the opposite. Hello Jeti! I live in 2024. Don't tell me the pairing/set up can't be done easier than this. I'm packing the sh*t down, and I'm going to return it all back to the dealer. Bye, Jeti!

Lovely, beautifully done

This is an outstanding test. The values on the top left corner of the screen are key. The numbers that range from 2 to 9, indicate the signal strength received by each antenna on the receiver that is on the plane. If these values are 2 or higher, then there are no problems. The third value, which ranges from 0-100% is the quality of bidirectional communication. As long as this value is above 20%, there are no concerns. This value can drop occasionally even to 0% for milliseconds, with no loss of link. The test also showed that, besides having a stable signal, the link was maintained at all times (no failsafe or lost link alarm was triggered). Awesome radio!

Thank you, what can i do if i have no jetibox on my DS-12 ? Thanks a lot

Thanks! To the point in less than 3 minutes. Very nice.

You forgot to toss the transmitter on the table. It’s ok it won’t break

Okay so about 1 Km? I take it you are not flying further than that LOS? Have you tested further out to lower signal strength and/or signal quality? Thanks

I had to take off those SF knobs, they get in the way of your fingers if you are a pincher..and what the shit deal with the blurred out stufff.

Pésimo video. No se entiende. Es como Darth Vader explicando sin ganas...

Really good demo thanks.

👌

Awesome!!!!

why can't i run Vario in rex 7a receiver. I have bought the bin file in the transmitter, it is marked that the update was fantastic and the receiver is silent 😟😟😢😢😭😭😭😭 update information, the bin file is with numbers, e.g .: ACT-4264562555 and I have Activation.bin, does it matter? I bought 3 items and there is only 1 file

Really enjoyed this, excellent 👍👮🏻‍♂️

OK très bien !

Is there any point in rushing through the menues that fast???? Thumb down!! Noone can follow you that fast and learn from that. Ridiculous!!!.

Those main gear tires were 108 inches in diameter. There were only three bases in the US that could accomodate them- Carswell AFB, Edwards AFB, and Offutt AFB. The need for a four wheel main truck was painfully obvious.

I did it but I got the message “Unable to write parameters” what should I do?

Hi ,Do You RECOMMEND this jeti ds12?. Cheers

At 2:00, it shows the other 3 pins configured for servo, ex bus, and sensor. Is it possible to chain a sensor like the MT125 to the Rsat? I would like to add an Rsat, but I don't have any more pins available on my R7.

could you have programmed it, so that once the gear came down, the doors would close again? Then whem you were to bring the gear back in, it would open the door first, then the retracts would kick in?

very good

So, it is needed to buy the Vario function to Jeti? And is needed to do that just one time? Or every time that I bought an assist receiver?

sorry for my ignorance, but what was the conclusion of the test? I want to buy it but these tests are conclusive to make the decision.

Great video! thanks for sharing

This a great video Rostislav. Thanks for sharing this video. It has helped me and keep up the good Regards Kevin Australia.

Hello, I would like you to give me your opinion regarding a problem I have with the DS12 and RSat900. I was trying to link the satellite with the transmitter following the steps you did in your video with the DS24 but the transmitter does not recognize the RSat900. What do you think may be happening? Greetings and thanks for your videos

Nice 👍👍👀✈

Very nice , 👍👍👍👍✈

Topmodelcz.cz???

Toujours aussi top il vous faut continuer merci

Merci pour vos vidéos un vrai plus pour les utilisateurs

How can I bind 2 rex7 to use 14 Chanel’s?

AK signal Q = 0 model sa neda riadit......

mam tiez problem s nizkym ,presnejsie 0-vym Q,v mojom f5j modely,ako spravne umiestnit anteny? skusal som uz rozne kombinacie...nad zemou cca 100m vo vzdialenosti cca 450m odo mna...bezne lietanie f5j...vies mi poradit?DS16

Super video. Rosťo díky.

help can not find tis vario bin file ????

I have several problems whit the signal on my ds16 . I test the rex7 and clone sat configuration in a closer to city place, the result is incredible bad. Many low signal and a eternal fail safe. Can you suggest me some configuration?

If I try to paring two rex7 as the same procedure? This is like dual path, what is the procedure to do in clone version? Thanks a lot

Could you explain how can I paring 2 clone receivers whiteout sb200?

Jednu věc nechápu. Jak je možné vidět model této velikosti na kilometr? Eyes like a hawk... Respect! 😉

Your videos are very helpful please keep up the good work

What is the setting of the Q value threshold for weak signal warnings?

Great plane. Greetings from Poland

Pěkné. Jen o ten podvozek bych měl strach.

Thanks a great help. Could I however ask you to go a little slower when running through the menus.

Maybe i am too stupid but can u explain me what u did?! I am not a professional and i didnt get it