Видео

Thanks for the tutorial 30 minutes later up and running

Hello, thanks for the great video. I had to replace the rollers on my s300. I got everything back to gether, but I can't find where the micro limit switch fits back in place next to the stepper motor. Can you please help on this location? Thanks!

Thank you!

Had a slightly different model, but your tutorial worked really well. Thank you very much.

Very complicated replacement, could not have done it without this video. Thank you!

Thank you

👍

My pick rollers from a 2012 ix500 lasted until 2024 @ 117k sheets. I replaced them and seems to work fine again.

Helpful video and this is an easier disassembly process compared to the complete removal of the circuit boards that other videos show. Do you have any recommendations for getting the new tires aligned at exactly the right location? Perhaps marking the spot that the original, now degraded PU rollers, occupied?

Okay...so I bought the roller kit with the rubber already attached, placed them in and reassembled the S1500. I am still getting a hum/stop/hum and the paper barely going in. So is the problem, I didn't beat the rubber tires with a mallet? Any advice would be greatly appreciated.

Thank you so much! This was a tremendously helpful how-to video!

Thank you VERY much for your tutorial! I was hesitant to do it myself, but took it to a Repair Cafe event, and some of the volunteers were able to fix my scanner using your video. It did take a while, but it is working again and I couldn't be happier.

Thank you so much for this tutorial. How long would you say it would take a "regular" amateur person to replace the rollers like you show in the video?

Thank you thank you thank you. Fitijsu said my s1500 is no longer repairable. I located rollers and Amazin and although it took me 8 hours, much to my disbelief my scanner is working again. I never could have done it without your video. Hey, I had only o e screw left over. Not bad

Where do you get the replacement rollers?

Where can they be shipped to have it done ??

Put the plastic over the metal. Did it wrong.

worthless

thanks bro this has realy been helpfull

Good tutorial working for scanner fujitsu

Great description of the process. Any hints on removing debris from melted rubber rollers?

This was helpful for fixing my S1500 when combined with this other video: ruclips.net/video/IdBPX-tL0xo/видео.html (Japanese, but still very clear what to do with just the video).

Thanks for the video, do you happen to have the part number for just the rubber rollers you cut off in the video? I think I have the part numbers for the entire roller kit, but it seems like it would be much cheaper to just replace the gooey rubber tires. Thanks

How to place the feed rollers ? The beige coloured ones...mine are melted into a gooey mess & need to be replaced

Thank you fro sharing. Your video has been so helpful. Greetings from Italy 🇮🇹

A video for replacing the rollers for a Scansnap ix500 would be really helpful. I have ordered the rollers from you, but I have no instructions on how to proceed.

私のｓ５１０もローラーがだめになったので、部品だけ手に入れましたが、この交換作業は素人にはむずかしいですな。

The scanner was thrown away in the end

It did not help me

this video help me, thanks :)

Mua cái này ở đâu bạn

In this video right about 2:05, the roller cover plate comes right out, but mine seems to be hooked on something on what is the left side. I wiggle it and try to lift it, but it doesn't come out. I didn't actually unhook the front section, but that doesn't appear to have any bearing on this part.

Opening this thing was hard as heck! Thanks for the video!!

How did you get the roller out of the scanner?

Thanks for helping me :)

thank you !

Video on how to do the whole process - PA03540-Y075 PA03540-G078 feed exit roller tire for fi-6130 fi-6230 fi-6140 fi-6240 fi-6125 FI-6130Z ruclips.net/video/Pncqt6KhIzw/видео.html

漂亮 谢谢分享 终于可以换 滚轮了

this video help me, thank you

Thank you sir

Я тоже долгт мучился, но я менял с термопленкой вместе, там было немного консистентной смазки в комплекте. После 5_6 разборок сборок удалось заставить вращаться, да и шприц с смазкой я выдавил полностью.

эта ткань не скользкая, вообще, даже со смазкой пленку клинит сразу после поджатия. лажа полная ни одного листа принтер не распечатал.

É isso o que eu queria saber, se consegue substituir o rolo(borracha). Agradecido

How to remove scanner feed roller of Scanner fujitsu fi6240 ?

how did you get that out of the scanner?

wonderful