Видео

I cut myself twice in the last three monthes and im scouring the internet for tip. Thank you for sharing

Awesome simple but effective solution

That actually isn’t a drawer pull jig it’s a cabinet hardware jig

It's a tough business. Years ago I had an amazing handcrafted product that I tried selling at craft shows. I could never figure out why, getting such great comments from potential customers, I could not sell the darn things. The vendors who seemed to be making lots of sales, were the ones selling low ticket items, say $20 or less. Maybe you can come up with some ideas of products you can sell a lot of but for little money? Good luck!

I was being rushed on the last job I worked on and could not get this jig working for me. Usually tools like this go right to the trash but, this one didn't. I'm going to revisit it since I just installed more cabinets. Which I wasn't qualified to do

What size drill bit did you use?

religion is a death cult. please dont spread your cancer.

Thanks so much

Also, what mandrel do you use? Thank you!🙏

Where do you get your ring cores? Thanks

It was your first show/outing. . It takes time to develop a sales strategy. And by the look of it you have some excellent products. Be positive and keep forging ahead. At some point you will start getting commission orders. All the best mate.

Exactly the kind of video i was searching for!

thanks mate

Thank you for sharing your experience! Hope you continued on to make more sales in later fairs!

Great video, I'm going to try this five cut method. Thank you for posting.

Ouch

Crat fair is good to wood workers and pick up my dear offer Jayson Caldwell and program to my is Heather pandas i do want pancakes

Keep doing good things! Don’t let a low sales day bum you. Fall down 9 times, stand up 10 times.

Awesome! Just starting making flags, I have to try this!

Yikes man I’m glad you are ok now… did you have any lasting nerve issues in your hand?

I’ve always been afraid of this.

Beautiful finish

Carving the stars gives a much better look

An easy way to get the centre of any rectangle (without arithmetic) is to draw and X by placing your straight edge from top-left corner to bottom-right, draw a line (roughly in the middle, does not have to be full length) and repeat again from top-right to bottom-left. The centre is the point where both lines intersect. You can also find the centre of a circle by basic geometry (using Thales theorem): if you have a right angle in a [virtual] triangle and the vertex of the right angle lies on a circle's circumference, then the line segment joining the other two vertices of the triangle must be a diameter of the circle. Basically if you place the inner corner of a [framing or carpenters] square on any point on the circumference then the two points where the square intersects with the circle circumference mark the extents of the diameter (a circle has infinity many diameters, lines though the centre enclosed by the circumference, but in practice people often just say 'the diameter' implying that there is only one instead of 'a diameter' even though the latter is less likely to aggrieve your friendly neighbourhood maths nerd).

thanks for the safety tip. I just got my first bandsaw and haven't made my first cut yet, your video is very very helpful. Thanks for sharing.

Jesus you got that deep

Dude, you showed up on my shorts feed. Lol, awesome

Thanks for making this easy to understand.

Good video! Your process seems very effective, thanks for sharing.

Yep. I get laughed off all the time on FB reels when I try to tell these idiots they are risking harm to themselves.

How has the online payment workinv for you, I was wanting to sell online but did not know how easy online money sales would be.

love the excitement, but man.... you have alot to learn.

Very well explained. Thank you

When are you posting the accident you had with the band saw?

I did that too.

you did one thing wrong. You didn't use enough clamps on the 3 pieces of plywood you glued up. 25 clamps is just not enough! Needed at least 40.

Did your client happen to be Eddie Hall or Brian Shaw? I noticed a piece that looked exactly like this in the background of some of their videos. If so thats super epic!

❤thanks

First time doing woodchop I did well for a couple of weeks then I went to cutting in a motion where it slipped and sliced a part of my finger and nail but I still got all my finger next time I'm using extra wood to push it in when I'm doing angles

You have all the support my friend 💯💯🔔🔔👍👍

Bless..

😯

I used Woodglut instructions for this and I already did it :)

Very cool!

next time use laser cut stars and using the silicon star template to place the stars

If you seal the stencil with a clear coat, there should be no bleed

Gorgeous!

Thanks for sharing... Glad it wasn't worse. Thumbs Up !!

I cannot believe how easy you explained this. Had to subscribe. You are awesome sir! Thank you.

WAIT!!!! Shit wth! Ok... I'm ready 🤓🍿