Видео

Has anyone put a 180 width tyre on fz6r

You forgot to remove cap from res to allow fluid to retreat would have been easier to push piston back

This was a helpful video. Thanks!

Awesome vid man, thanks, maybe I missed this part, but did you not need to loosen the brake caliper at all? Just lifted it, took out the chain, main axel and rolled the tire right out? You didn’t loosen anything on the brake caliper?

thank you for making this video and making it so descriptive!, kudos my dude!

Nice vid

For anyone watching this, you can rent the piston compressing tool at any AutoZone. They charge $60 as a refundable deposit. The 'bit' that's on the tool when you open it fits the Saab (no adapter needed). The backing plate slips over the tools handle for correct positioning against the outer caliper fingers. And yes, the adjustable wrench helps to keep tension on the jam nut. Both sides turn clockwise to compress the piston. One other tip: when your done with install raise & lower your E brake lever several times to seat the piston against your new pads. Hope this helps😁👍

Any chance you have a link to the stand?

Can I use a C clamp to compress the caliper piston???

I can’t get my caliper off my Saab.. it’s almost like it’s rusted 🤦🏻‍♂️, I’m so sad that I couldn’t get the job done bc of this. Does anyone know of a way to help loosen it ? I’ve prayed wd40

Thanks for taking the time.

What is the bulb u used?

Thanks for the video! Very helpful 👌🏻👌🏻👌🏻👌🏻

That music is intrusive

thank you for making this video I've followed it step by step successfully saving loads

How we get only the mirror.

What is the flowair end of the car? 🤨

Awesome video. I'd be too OCD not to vacuum out all the leaves and clean out other debris before putting it all back together haha.

This was incredibly informative and easy to follow. Thank you

Thanks for the quality video. Even I was able to change my filter after watching.

Diggin the music man! 00:39 I'm about to bust out a Gretsch hollow body, stick an OEM Saab Scania cabin filter in there for a display of gratitude for what once was, have a moment of silence, then turn it up !

That's not a phillips head...

What rewind tool fits the Saab 9-3 NG? Thanks,

Tak.

Great video, here are some observations/comments: 1. When doing rear brakes, put the car shifter on reverse or drive. Disconnect the battery to avoid unadverted switch actuation. 2. WIth a shirt hanger and make an S hook to hang the caliper off the Suspension spring. This will prevent any issue where you may drop the caliper and strain the brake hose. 3. Wear rubber gloves, asbestos can be absorved, at a much lower rate, by your skin. 4. Open the brake fluid reservoir and if is too full, remove some fluid to avoid spillage during the caliber push. Once pads are replaced, drop the car off the jacks and push brake pedal several times to bring caliper to working condition. Replace fluid and reservoir cap once you are done. 5. You can use a C clamp as an alternative tool, to push the caliper and allow installation of new pads.

Dude, what size max can I put on my FZ6R

How to remove hub? Not changing socket so I dont need to unbolt right? Should pull out? Just need to unbolt rotor. How does hub/sprocket come out in one piece?

This is a true fucking nightmare. I can’t get the alignment right

Lol first it said torque to 64 foot lbs then it says 5 seconds later to torque to 90?!! Which one is it

Is this the same process for a 2003 9-5 linear? And do you know where I can find a passenger side turn signal socket? I’m having a crazy hard time with this car.

Very good video. Thanks

Idiot!

What stand is that?!

Wheres your glove? Safety first. But thank you for the video.Thumbs up.

Thank you very much! Huge help!👍🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻🌷

You're also supposed to remove the water drainage hose and clean it to prevent it from getting clogged with debris over time... :)

i did this on motorcycles when i was 12 in 1982

Very detailed and informative video. Well shot and nicely edited. The best part is the details on the tools used that are visible on the screen. Your video is the reason that only my wheels go to the shop for a tire change. Cheers !!! Keep up the good work.

Awesome thanks

Does each side of the car have the piston turn clockwise? I have seen caliper kits come with a left and right hand tool and wasn't sure why.

Ended up having to take mine to a mechanic because I could not for the life of me depress the calipter piston.

awesome video and instructions. This was very helpful...Thanks

Thanks for video now I’m can do my own brakes from now on

I hate those little crank jacks the cars come with. If you do your own work make it easier with a floor jack

Thank You for sharing ! For some odd reason, I hadn't even considered removing the broken glass while on the assembly ! Thank You. I also didn't think to use a C-clamp to ensure it properly glues on. Thank You. It's all Good and Bonus for replacing the mirror in inclement weather. Stay Safe and continue with the videos. Thanx again.

Next time don't add music

How's the Diablo compared to the old Battlax? Nice Video!

Thank you the video was real helpful.

Great Video! Thanks!

Dude, wow! You put some hard work in there to make an excellent video. This will really help a lot :-)