Видео

Please, connect the wire with the small PCB, the small PCB is the one which is responsible to deal with power supply and charging. You just need to connect it in the same way as I did in the video.

@@PiyushPrasoon hi. Просто + к + а - к -? Без среднего провода?

Nahi original to nahi hai, but one can not figure out the difference just by seeing it. Picture resolution is also quite similar.

Its completely depends upon the availability of space, if BL-4UL battery can be fixed inside the speaker then go ahead with it, it will work. 🙂

@@PiyushPrasoon ys i connected bl 5c😢 ...bt not turning on no led turning on

@@abhijithnv3459 make sure you have connected the power controller small PCB circuit. check if you have detached it from the previous/old battery.

@@PiyushPrasoon yep i didn't disoldered that frm the beginning...then i tried without the pcb ..then also noo lights coming

@@abhijithnv3459 I would suggest not to do the direct soldering of battery from the bigger PCB. you can solder it via small power controller PCB. please watch the video from this point: ruclips.net/video/vzXPpkpwiIs/видео.html In case it is still not playing sound, you have to do a basic connectivity check for all the existing connection. and check the LED status. Better connect it as I mentioned above and the try to connect it with power source and check if it is charging and check the charging indication on LED, if it will show the red indication it means it is getting charged and the connection is proper.

😂😂 कोई बात नहीं, के बार फिर से देख लीजिये गा 🙂

Absolutely it's just the replacement process, as mentioned in the video title 🙂

Yes, the speed will be a bit slower, but speed also depends upon the distance/obstruction between the jiofi and the router. it should be within 3-5 meter radius in the line of sight.

Just peal off the broken ends of the wires and 3.5mm Jack and do the soldering.

it price is 5500 INR

I have purchased this from a local vendor, you can view the number in the video.

Waah nice observation.... Fir syad lutput gana bhi gane lege ga

There are several alternatives to auto stop. One of the easiest ways is to use 555 timer IC

If the gauge enters the red boundary - it means your bike can go to reserve mode at any point of time, this is the time when rider need to move the petcock knob manually to reserve position else your motorbike will stop moving. After setting the petcock position to reserve mode, your motorbike will start consuming reserve gas from the gas tank and keep on moving until the gas tank is completely empty. At this point of time the gauge will be pointing all the way down the red end. Note: The quantity of reserve gas in the gas tank may vary depending on the motorbike brands. As per my knowledge, 2-3 liters is the minimum reserve quantity of gas in the gas tank for most motorbike brands.

Oh, I just took the back panel off to show the components and accessories on the Motherboard at 3:09

A height adjustable mechanism is given by the company in this table. This is a telescopic mechanism in which the outer pipe has a threaded hole with a knob if you want to adjust the table you just need to slide the inner pipe by moving the table up or down then you have to tighten the knob to make the table fixed in that position. If there is no way to adjust the height of the table then you have to use it the same way with default height. The table in the video with the knob is enough to tighten the table and keep it stable in the desired height so no holes are needed in the inner pipes.

right, some TV may have the OLD BT chip used i.e. 4.0 or 5.0 initial technology BT chip. BLE 5.0 enabled chip is having the capability to connect with multiple devices. Can you help me with you TV Brand and its model number?

Hahaha nice observation, but my answer is no, I was not getting the shock as current choses the easier path to complete the circuit 😊 But 1-2 time I got the 💥😆 you might have noticed in the video the electric arc once strike my thumb 😅