Видео

To slow! I’m running my little cnc at 230 ipm! And producing nearly zero dros! I have the little crossfire table. I picked up the Lotos LTP5500D CNC plasma cutter off Amazon and it runs awesome! That said, the ipt 60 torch handle it comes with is garbage and you can only use Lotos consumables. They’re just different enough that other standard ipt60 consumables WILL fit BUT it’ll misfire like crazy because Lotos are assholes. So, I picked up a machine torch built by Plasmadyn based in MO (Missouri) modeled perfectly on the Hypertherm x45 torch and uses Hypertherm consumables, or just buy the ones made also by Plasmadyn! Holy shit the difference is NO COMPARISON! PlasmaDyn makes a fucking awesome machine torch for $300! And their consumables are literally a quarter of the cost of Lotos consumables!

What happened is that I also have a bobcat 731 with the same symptoms

what is the easiest fastest way to learn to operate this plasma machine ?

Can you use this like subwoofer in the car ? Using the aux ?

I just got the same lathe. Going to try to get it going this weekend using a vfd converter. Do you have 3 phase or are you running a converter?

I have a standard flow skid steer that has 15 gpm. I was considering this same attachment.. by any chance do you know if it would work correctly?

Did you run power directly to the battery or do you have a busbar setup?

Very informative video, man. I noticed the cut isn't exactly 90°... I've noticed that on some of the plasma cut parts I've ordered in the past also. How do you remedy that, or is it just normal? I just ordered the xr and plan to cut 1" so any advice would be appreciated.

did you find out the problem mate

Any update? my Gehl R105 is making the same noise

Is there an app to adjust the bass/treble?

I am looking at buying the same brush cutter. I was wondering how yours is working out for you?

Any update on fixing the whine noise?

Have you found anything causing it?

what the heck is it 🤷‍♂️

🏆⭐🤗🙏 Thank you for sharing this

Tell Mach1 you seen this video if you buy one😊

Just a question here, is your water level too high? Maybe affecting your cut quality?

true

Cutting counter clockwise?

Great advice. You should check out the Beck's Armory Machine torch holders for the XR. It has a laser cross that could reduce the time i takes to line up your torch with the pre-drilled pierce hole. :)

Do you happen to remember the settings when you did that cut?cheers

I just got a T650 with 7100 hours. Got ripped off of course. First skid steer. Left drive motor is making similar noises.

Solution. I swapped the hoses around and it started working just fine. Im still curious if there is a way to reverse or change rotation on maximum flow with the skid steer controls or if swapping the hoses around is the only answer.

Ohhhhh so that’s how you electrical start it I knew it

Ah, you sold the XR.

What happened with the XR table?

Any update?

I envy you for having enough time to cut 25mm (1 inch) with 65A. I use Hypertherm Powermax 125 and cut 25mm with 125A at almost 4x the speed. Cut quality is not that great but the parts I cut do not have to be that precise. I cut a lot of material, some 1000 tons or more per year. Most of it is in 10-25mm range but i often cut 30 and 35mm too with pre-drilled hole just like you did. At 125A you can pierce 25mm easily, i think i set my machine to 2 or 2.4 seconds pierce time (not sure, i have like 200 profiles for cutting) but 30mm is not suitable for pierceing. It is possible but it can (and usualy will) damage the cutting head due to erupting molten metal blown out by compressed air. In any case, great job and very nice cut quality. I had my doubts about 65A being enough for 25mm plate but at that low speed I am amazed how good it worked. Great job! You can check my channel and see how I work too, I would be happy to share experiences with you.

Rusted Stainless steel hmmm

I have a 1999 773G that whines more with lower throttle. Tracks straight and has plenty of power, but it just seems like it shouldn't be whining so much. It definitely doesn't whine as much as the one on the video. I do have some water in the fluid somehow- maybe that's what is causing it.

How old is the driver??

Are you just using air?

🤷 Promo SM

I made my replacement slats out of scrap 316 stainless steel. No more rust. Like the drain idea

Nice table I was looking at that one to buy for home hobby stuff. I have a spot in my basement. Not that pricy for what you get.

Hold er down and hope for the best 😂

great videos man! i have same setup and i am running into issues cutting 1/4" without a bevel. what kind of feedrate do you suggest for 1/4"?

You should check out lift arc studios. He has a 5 by 10 shop Sabre. Has great information on it and is tied in with shop Sabre now. Does some thick cuts on a welding table in one video with I believe over 500 holes in 5/8. Also jd squared has a nice table. I like both company’s have awesome tech support and shop Sabre now owns Langmuire

what did you get out of it??

I'm interested in understanding your choice to switch from one plasma table to another instead of considering a upgrade to a fiber laser cutting machine. Could you share your reasons? I currently own a Pro, and it works great!

I've only had my pro up and running about 3 months or so and im struggling with finding the time to actually get my few jobs for people done, but ive had the thought that if i get to the point that i want to expand to a bigger table, I've had the idea of using my pro as the guts to just make the table bigger myself. I feel like it would mostly be a bunch of square tubing and buying longer lead screws. Maybe im crazy but i feel like i could do it. Probably will be several years at my current rate. I am very curious what the price range is for the next sizes up like 6x12s.

I arrived at your channel from your Facebook ad selling the table. 👍

First off air compressor you guys want or have the need for air get way from cheap junk and spend the money on a good unit commerical at minimum industrial is the way to go there is no better option Curtis Leroy Gardner Denver Quincy those are the brands you need to consider and yes I'm talking 10k units but you will buy them one time and never again for the rest of your life they are life compressors 30 40 year units. I use a 325 Quincy 21cfm 2 stage 5 horse motor 80 gallon tank and a inline dryer. Spend the money on your equipment and it will take care of you buy cheap and it will cost you more in the long run and possibly cost you your life. A unit like mine the same issue isn't possible

Did you fix this mate I have the same issue

nice cut! hey i just bought same setup and was wondering if you setup each tool per thickness in fusion360? did you go off cut chart in book?

NICE WORK.

Nice! Can I ask what your amps, ipm and cut height were?

Laser cutting?

Wow that was much cleaner than I’d expected! Thanks sir!