- Видео 9
- Просмотров 80 770
QS Autosolutions
Добавлен 8 ноя 2014
im here to share my own experience, I hope ppl like my videos and subscribe hopefully, thanks
2009 Mercedes c class 2.1 diesel EGR and Intake manifold removal
2009 Mercedes c class 2.1 diesel EGR and Intake manifold removal
Просмотров: 116
Видео
2017 opel vivaro Renault traffic 1.6 diesel starter motor removal
Просмотров 6534 месяца назад
2017 opel vivaro Renault traffic 1.6 diesel starter motor removal
2014 Mercedes Vito viano diesel alternator removal
Просмотров 3244 месяца назад
2014 Mercedes Vito viano diesel alternator removal
2015 sprinter intake manifold removal
Просмотров 36 тыс.2 года назад
2015 sprinter intake manifold removal
2015 Mercerdes sprinter erg valve and cooler removal
Просмотров 1,2 тыс.2 года назад
2015 Mercerdes sprinter erg valve and cooler removal
2013 ford transit diesel glow plugs and intake removal
Просмотров 4 тыс.3 года назад
removing of snapped glow plug
2013 ford transit diesel glow plugs and intake removal
Просмотров 17 тыс.3 года назад
snapped glow plug removal
nissan micra diagnostis
Просмотров 2,4 тыс.3 года назад
battery drained , alternator is charging , battery is fine too, owner may have left lights or gadgets on, causes draining battry
Thank U my friend great video helped me alot thank U again Top man
It's a lot of work for a routinely replaceable item . Great design 😐
French design lol
Crap vans!
This van is good though, nearly done 200k miles , second time timing chain replacement
Hey!!,quick question for you...would really appreciate help if you could? There is a wiring harness that runs on top of that engine and a plug that comes off on the middle right side,the plug seems to sit around the front of the fuel filter housing and goes down to the left side front of the egr cooler,do you know what it goes to? Its just a little short wire and plug on the right of the wiring harness and only one in the middle on top of the fuel rail. Ive just done the waterpump and fuel filter housing on this and lost to where this plug goes unless it doesnt on some of these engines?
Awesome details video. Hope you’ve recovered from your detox /cold symptoms since 2015 😅.
Thanks very much
How many miles did it run, How many hour including removing inlet manifold?
tanks very much im from brazil and i dont like mercedes because i work on them
Hi. How long did this whole process take you?
f..,ing making a video and caughingblike a c*****t
You got Covid or something man?
Hi no , I’m asthmatic.
very useful, thank you so much 😊
No problem
Did you have to drain the coolant before you took it off? I saw another video from someone saying they had to drain the whole coolant system!
No won’t be loads of coolant , just top up after job . If u drain it all , u will have to bleed system, bigger job
quit smoking you cunt
Just did this job and you actually don't need to take the egr piece off, the intake will squeeze through the gap, just a bit fiddly 🤟
how do you know that the egr is bad on that car?
It had egr fault code
Thanks for uploading the videos on this .I've Just started to strip mine down and has reassured me that it's not as bad as mercedes made out ! 900£ Labour! I'll sort it lol .👍
И будь здоров
And Coldrex
Кто кашляет ? Купи hols
Thank you🙂
Bless you
did you come across p02a7 ; am driving van like that over year now (not limode but still half turbo , had it done for vacuum leak before , but am suspecting o2 sensor , have you had o2 sensor problem on this engine before what its symptoms like ? I checked injectors for leak no problem found , your openion in this matter will be appreiated mate
Sorry don’t know this code
Try looking at your #4 injector, injector harness and trim levels. www.autocodes.com/p02a7.html
Thanks for adding the clip, made my life so much easier, cheers buddy
No problem pal
Thanks mate....doing this tomorrow.......people say to soak the plugs in oil first and get engine warm before.....quite hard to do if the manifold is off etc.?
Plenty of WD40 may still snap , I had one snapped ,I had to buy removal tool from eBay
Cheers for the video mate. Nightmare job
No problem mate
Was the gasket or you replace the entire piece? Mine when is getting too hot is blowing somewhere and i think is from there as i have the egr stuck opened as well
Hey mate do you have video of you cleaning the EGR valve out at all??? Or do you know if it’s even a serviceable cleanable part or do you need to buy new one???
I don’t clean them as electric actuator may fail too, Egr not expensive from Europe car part, labour cost more, make sure the gaskets are renewed!
Superbly detailed video and explanations. The best video about this in all internet.¡Gracias por compartir!
How did you disconnect the 3 way electrical connector? Thanks
How much was the whole egr? Was oem? I think mine is leaking
u can get used one for about 100 pounds
@@Autosolutionsautolocksmith used one can last one month or 1 year. You never know
@@MihaitaMYG that’s true , but the genuine one from dealer is expensive, so I was to choose I would go for a used one but it’s genuine mer part with low mileage
Where about are you?
Manchester UK
Hi , I got sprinter same model, I have taken egr and manifold out cleaned and put them back now van crank but engine won’t start?
Did you disconnect the metal fuel pipe ?
if you did disconnect that fuel pipe , should not try to start straight away , need to turn key on and off good few times so no air in the system, now you will need to do injector bleeding it’s easy , just do injector one get someone to crank , spray some easy start , connect the jump lead .
I would of spent hours trying to take it apart separately! Thank you!!
No problem
covid for sure lol
Thanks for the comment
Corona.........
Soo
Gećmiş olsun 2012 siprenter emme manifoldu yağ kaçırırmı söktüğünüz yerin alt tarafından yağ geliyor birde çekiş düşüklüğü var ıslık sesi de var saygılar iyigünler
excellent video mate you saved me a lot of time.thank you
No problem my friend
Blow your nose
Too late now
Bro go get tested that's fucked, but thanks for the info 🤣
I’m asthmatic
Ai încălzit bine motorul înainte de a demonta bujiile?
Nice work
Thanks pal
Great! And get well soon...
Thanks mate,
Can you please tell me what tool can be used to remove the unit on top of the EGR valve? The bolt seems to be a T28 at an angle?
Hi yes , need to long t28 , u can’t see the bolts, align the t28 by hand at an angle then use a 1/4 ratchet soon u lose it will be easy turn by hand
looks like a very ugly country with a depresssive weather. good video anyway.
Thanks