Видео

De verdad me sirvió de mucho ver este video gracias...

You only had to change or adjust the carbon.

By luck it works.😂😂😂

How did you get the casing off?

well done! the stator motor is easy to rewinding.

Excelente video saludos desde puebla pue

nice🎉👍👏

but didn't you replace the bearings?

Thanks from Finland. When I disassembled my stapler, the small white part flew to floor and I was wonderin how it should be assembled. Then I saw your video and saw that the PCB should be assembled askew, not straight as usual. Now my stapler is safe as that small part is for safety purposes. It prevents triggeting if the stapler hasn’t bedn pushed against the surface.

Tidy

יש קישור אולי להזמנת המתג ? תודה מראש

תותח אחי אכלה סירטון

Black & Decker owned Star Power Tools, which was based in Civate, Italy, since 1961.

This is a counter fit fake makita battery

Buenísimo éste vídeo muy profesional un video instructivo y muy útil para gente como yo que no posee los medios económicos para hacer realizar el servicio oficial. Muy Agradecido. Lo que necesito saber como se saca el eje del cabezal donde va el disco para cambiar ése rodamiento. Muchas gracias

Lot of grease..

Can you tell me where I can order an armature for a hitachi dh 38ye ?

top

Kya ap mujhe is hammer ke piston kit ka model number de sakte h???

this cordless drill 60nm of torque in 12volts amazing old tools!

Tengo una igual a esa la que se ve en el video, quería sacar el engranaje grande, pero no tiene ningún seguro, los dientes los tiene un poco desgatados, y no llega al piñón pequeño, pero no encuentro la forma como sacarlo, para hacerle un chapús o chapuza, para acercarlo más al piñón, tiene como la mitad de los dientes desgastados, espero su respuesta, saludos, ya le di mi like.

muchas gracias por compartir tus conocimientos, saludos desde Medellin Colombia.

Thanks for this Video. Helped me a lot to repair mine. 🥳

Very nice 👏👏

Temiz iş çıkardınız.Tebrikler.

Thank's for the vid. My machine has the same signals as yours and does not run. Unfortunately I can't exactly see in your video, where the exact problem was and what you did to run it again. Some exchange of peaces?

I like this, repairing tools and keeping them going even if it’s cheaper to replace

I’m just trying to figure out how often I should clean and grease this thing and how.

한국 아닌가요? 외국 댓글이 많습니다. ㅎㅎ 취미와 수리비용 또는시간은 반비례 입니다 ㅠㅠ 그냥 공기계 15불 주고 사는 것이 더 수월해요;; 참!!! 보쉬는 메이커라 공기계도 비싸겠네요.ㅠㅠ

You replace the dead batteries ?

Soldering a Battery is a Bad Thing™

Like and sub at first seconds! Thanks RUclips for spying me because I have this tool, but label is ruined and I couldn't find out, which model it is AND there you showed up!

❤

I understand that the screen mounting hinges ripped out of the case with the plastic (6:35), how was it repaired?

I think I bit a little more than I could chew, I fixed someone’s drill last time and then got referred to some other people and now I have 11 different tools I have to fix😂😂

Excelente video!

Mesure d'agrafe?

Hello. I lost the screw that tightens the blade and I don't know how to replace it. if you can help me with a picture, please.

How do i remove/replace the footplate??

I have this same model of saw which has been repaired 3 times when the shaft stops moving. What breaks inside the unit for the shaft to stop moving?

this jigsaw is fake or original made by P.R.C. sir

I watched the whole video for small piece fell off but you can't fix somewhere??

Excelente video, muy didáctico!!!!!

Rs550 motor?

update to this battery today?

good as new well dune

Почистил бы прежде чкм собирать

ive got the chance to buy one 20 pounds just might go for it good video

next time try upper camera angle

thank you good