Видео

Good video BUT DO NOT torque to 20nm. Correct spec is 8nm plus 180 degree turn. I got FUCKED listening to this dude.

Thank you for making this video it never would have crossed my mind to do this. Also thanks for making the short and to the point.

You saved me too ! Great tip. Thanks !

Thank you!!!!

Thank you! I was just about to take it apart, 5 minutes later it's running again

I HAVE A 2008 VALANCHE FLEX FUEL AND MY AIR BAG LIGHT IS ON , I tried you solution whats next mine did not turn off?

I just watched your video on the valve cover gasket. Good stuff. Where did you get that online manual? Which web site?

One of the lines I think it’s the return you forgot the put the clamp back on. Great job and great video

My not beep when i take the Air out of the tire

When you say, “you should get this tool,” it would be very helpful, if you mention the name of the tool. The one you tightened the fuel lines with, is something I’ve never seen before, in my life.

Thanks for taking the time to make the video. Do you have to do anything special to change the injector o-rings or copper washers? Did you do anything to try to clean the injectors other than an external wipe-down?

Is it recommended to unhook the battery cables while doing this? Also did you have to pull the fuel pump relay and turn the engine over a few times to relieve the pressure from the fuel lines? I'm replacing the valve cover gasket on my brother-in-laws passat next week. Same exact car. Have plenty of experience on domestic vehicles but none on German.

Legend, been trying to fix it for 2 hours and this fixed it

This did not work for me.

Thank you! Worked perfectly!

thank you so much .. Greatings from Germany ;)

Thank you very much you saved my tineco. A dub of silicone spray in the hole on that rusty bolt and some spins with a thin stick fixed it. You saved me alot of time and money.

Thank you, i dont use it that often, that is probably why the debris dries out on the motor and gets stuck in place, i was about to put this in the garbage.

Awesome video! It worked for me too. Thanks heaps!

Thanks!! For video it worked 😊

Youre the best bro😊😊😊

My Amazon Basics Wireless Mouse caused both of my computers to freeze randomly -- on six different versions of Linux Mint. I installed my backup mouse (never been used) and it solved ALL the problems. Both boot drives were corrupted due to multiple times of having to do a hard power off and restart. A replacement Amazon mouse is only about $10, so I will buy a new one. The old one has lasted for ~ 6 to 8 hours per day for at least 6 years.

What if i dont have a key fob

This TDI Passat is different to the one from the valve cover video right?

Thanks for the tip - it got mine working again. It sounds to me like the suction isn't as good as it used to be, so I'm using it on max mode instead. I also have an issue in that it often won't charge. I took the contact from the base station out and gave it a clean which helped but it still has the issue sometimes. Anyone know how to best clean the contact so that it charged properly again?

Bruh do you live on a highway. Loud as heck.

I will just pickle a few things and go. Shaving lotion, I shave a lot when I travel

My dude you just saved me! Was having this exact same issue. Did what you said and sure enough it fixed it so thank you!

If you build a relationship with your local HVAC service tech, when you need him, he’ll be there for you. If you always DIY, hire the latest jackleg in town and jump from one company to another, good luck when you have problems.

Any suggestions as to what to do First?

You should have gotten that coil wet before applying that cleaner that’s like putting on body wash then hopping in the shower good video though helpful

my 3.6 vr6 just goes up to 2000rpms and stays there, it doesnt jump, and sometimes it goes up to as high as 2500rpms

Had the dealership replace this over a year ago and instantly had high oil consumption thereafter Have had back in twice and they've just brushed it off as that's what these engines do after 100,000 miles Do you think it's possible the installed something incorrectly?

I have exactly the same car , has exactly the same problem, following your lead replacement all the parts like you done on the video and start up the problem still there….any thought or information greatly appreciated It Raul

Thanks! Just called tineco, and didnt have anything to lose giving this a try. Back in working order thanks to you.

How can we donate money to you?

Dude. I cant believe it. You are amazing. Saved us

Thank you for a video Raul so appreciated it .

WOW... worked for me as well! Thanks so much.

Nice demonstration bro, I have 08 Avalanche and I'm currently facing the same issue , tried your method and unfortunately it didn't turn the light off. Is there any other connectors that I have to hunt down apart from the one you showed here? Would appreciate your help

Just saved my ass and got brownie points with the wife. Awesome video!

It worked!!! Thank you so much

thanks great video you should change the title because this engine is in a lot of vws like the cc the atlas etc you may get more views

Thanks man it works for me

Thanks for this video! It worked for me!

Handy video. My mouse had the issue where the rubber wheel was slipping on the axle . If you also remove the pcb screws the entire assembly pops out and you don't need to bend/force the axle out of place.

🙂 *Promo SM*

Good job bro my light is on too I’ve got to check those fuses

Airbag fuse. Check it. Fix my problem

What size tool you use to take out the filter on the top