Видео

On this case, install an exhaust ducting.

Contaminated Smoke Detector , on this it is on Zone 2. Sa FDAS na conventional easy detection is by swapping contaminated zone, eg: Zone 2 (contaminated) Zone 3 good.

Yes Sir, same lang ng connection ng MK10A Atlas EDMI Electric CT Meter and may content na tayo Smart Power Meter CT Connection. Sa lahat ng CT Meter merong POTENTIAL at dun nakakakabit ang mga Current Transformer at ito ay fully electronic. Watch the other content at same lng ang MK6 Genius at MK10A sa connection. My diagram din na ginawa sa content.

Malapit lang Sir ng Raon Sta Cruz. Raon ay right na kanto, pero ito ay nasa kaliwang kanto.

FDAS ay Hindi adviseable na iOFF hanggat walang trouble as to their special function to alarm when a fire alert took place neither it is Addressable or conventional type.

Through smart gen intervention. And why to reset it to default?. In this type of trouble of Low Pressure, need no reset default parameters as it cause another trouble as its sensors set to stop the engine in case of anomaly on its devices been detected. 60C is alarming as overheat is possible engine related trouble. Coolant and Engine Oil must be check and basic parameters.

Halos mga 3 phase CT Type meters Sir with electronic and electrical schematic diagram. Electronic for CT, for voltage electrical. Meron na mga content riyan sa mga electrical tricks in finding CT on CT types meters.

Check ang starter relay at ok naman, check ang battery visually un may umido na kaya di na kayang dalhin ng battery ang starter motor.

@@ka-basicchannel3485 ...kahit 25 volts pa sir ang battery na may umido hindi talaga aandar?

Ecu ang nagmomonitor nyan, kung inibypass ang ang sensor na yan na wala namang anomaly ay bale wala na ang ecu para maprotektahan ang makina.

CTs were individually parallel connected onto electronic meter. Also have tutorial content on the working principle on CT smart meters.

Lods pag NO shut down alarm Mains under volt Ano Kaya sira nya kc ginagamit PA din namin kahit may alarm na ganyan gang ngaun nag loko na sya may nakita aq sa display CRANK REST ayon on/off na sya NG kusa ayaw mag tuloy andar namamatay din andar

Kapag walang redondo at about 3 to 5 years n ang battery expire na. Replace battery.

Meron almost same niyan paps, meron na sa channel diagram Smart Meter pahanap na lang po.

False Trigger lang ng smoke detectors gawa ng dust need pm.

sa smartgen Hindi yan reset lang Sir. Nariyan pa rin Ang trouble. Pressure sensor ay nakakabit sa makina and or faulty pressure sensor. during the run Yan Sir makikita result and same scenario kapag ipipilit intermittent.

Well in concept halos same ng ibang meter sa mga CT Connections, may content para riyan Smart Power Meter Connection wiring diagram narito lang sa channel watch na lang.

Sa SET Parameters menu po to activate ung input na sensors. Parameters rin Sir ung limit temperatures. Also watch na rin po ung mga Genset content po. Salamat.

check phase sequence relay and protection eg mechanism tight resulting to inverter / VFD to protect overcurrent and fault code display.

Crank Reset ay maraming cause Yan Ka-Basic , fortunately user friendly Ang smartgen na Hindi displayed as a code. check ung code 15 sa klase ng crank rest. Ussual cause sa Hindi coded na smartgen ay Battery, Also on other Genset ECU Protect eg ECU Fault Shutdown to check electrical anomaly on wirings. And also have a lot of Genset content and upcoming po to watch. Thanks.

Same situation bro

Yes Ka-Basic.

yes Ka-Basic, from 3 Phase kinuha lang Line1 at Line3 as temporary supply pa meter base na naka CT pa.

May content na rin rito paps, pahanap na lang title is Smart Power Meter CT Connection. Thanks.

cge sir,salamat..god bless po

Yes paps, sa load side ng nakaoff ang breaker.

it's a 2 to 3 hours continuous timer solid state. Ideal for most motor control that requires continuous operation transition for about 2 hours. Meron din tayu Ka-Basic ng timer na may trigger, nasa isa sa mga content multiple modes.

ah thank you sir,copy po..

Check paps Yung event Logs kita riyan Ang cause. Maaaring High Temp meron din po tayo contents para riyan and how to find event Logs on Genset.

Salamat paps sige panoorin ko yang tutorial video mo paps maraming salamat SA idea..

Ano dapat gawin pag high temperature paps?

Ok Battery ka-Basic, nandun lang sa Smoke Detector, vacuum cleaner lang muna para walang false trigger resulting to false alarm cause dust.

yes, No Load. as always. Ang IRT ay HIGH Voltage application about 1000v. Usually for newly built establishment na Hindi pa nakakabitan ng load eg lightings objective is to test wires kung pasado and of mga sugat sa wires upon installation ng wire eg cable pulling etc.

@@ka-basicchannel3485 What if 230V lang po ang gagamitin test voltage. Since single phase system lang po. Delikado parin po ba yun para sa mga lightings and devices?

yes nakakasira ng appliance Lalo na ung mga autovolt sa pagtetest, kaya no load as always. High Voltage transmission on no load and no voltage allowed upon any IRT Test basically.