Видео

Cool!

Excellent, Im impressed with the way you've measured performance. I will keep watching

why zinc and not some other metal?

Very interesting

Of Course: Add Thorium, Tritium, Deuterium in An Ermetically, Small, Very Confined Space!

Total run time was 5 hour and 5 minutes 256 milli amp hours. 325 milli watt hours average voltage 1.27 volts.

The carbon felt is a4 size not a3.

nice work there man quite impressive. for anyone who's dabbled in this area knows this is a lot of work and really takes a lot of desire and passion for something that we can all just go to the store and buy and seems totally pointless to most people. they don't get it. This guy gets it though. energy is power people. energy is power.

So much missing in this video!!!! How did you coat the carbon felt why does the Nick coating look like its powder ?! Why is there a guge bolt sticking out of the pipe is it SS or galvanized (zink coated ) iron bolt or dud you strip the galvanizing off of it .......

Very interesting. Great video

شكرا لك . وحضا موفقا .

Good stuff Dan!

Thanks for the video. I'm curious why you need to add nickel hydroxide. Is that necessary, and where did you purchase it? Thanks.

Hi Dan, I watched with great interest your frankenmill creation, it really started my own creative engineering juices flowing. I immediately saw the endless possible improvements and modifications that could be implemented. As soon as I saw your creation I though that it cried out to be mounted vertically onto a heavy steel plate L-shaped angle frame with motorised lift to the cross table/knee! I look forward to following your progress, well done and keep up the good work. Thanks for sharing this interesting video.

عمل جيد وشكرا علي بحثك ومجهودك وايصالك للمعلومة للجميع . من اين يباع لباد الكربون او لباد الجرافيت . وشكرا

Good to see you back, hope your feeling loads better.

Looks like the passivate failed ! I found it important that the passivate is 35 degree celcius or more

what is the highest energy density (in Wh/m^2) of your single cell nickel-iron battery, sir?

Maybe the tool was flawed from factory? Loosing the extra might have been you fix by the sound of it

I also followed caryex design but use an activated carbon air filter (foam like) instead of felt as I don't have one, he said that in his design he get around 300~mA of current. I get only 10mA, was that to be expected? Also what are the variables that affect the output current of the cell?

How did you make this?

Ets2 yeni videolar Nezaman paylaşılacak?

What's going on there Dan?

great

*Putting a layer of Manganese dioxide under the carbon felt would have doubled your power duration and amperage. Manganese cathodes can absorb 2 Zinc ions while carbon can only take in one.*

I just started looking into zinc-iodine cells myself, and i have basically no idea what i am doing yet, trying to figure out the best way to even source the iodine is still eluding me, i tried just basic 10% medical iodine solution and the amperage was rapidly dropping so fast in my crude testing methods, so i really appreciate you sharing your work, thank you!

Hi Dan. Interesting cell. l thought it would do better " bit dissapointing for you". thanks for sharing.

I've heard that heavy denim makes the best carbon felt.

What is it and what's it for?

Your problem is the pump pressure is not enough. once the steam pressure comes up the pump can't supply against it and the water flow drops. You need a higher pressure pump than the steam output you want. Also you could give the burner more air but you have to throttle it up and get the burner glowing. The fact it ran so long after you shut the oil off meant there was a LOT of oil pooled in the burner which is not what you want. Keep the burn chamber red and you should be able to shut off the oil and see the flame drop within 1 Minute if not 30 Sec, If it's burning longer than that you have too cold a bruner and too much oil flow for the air you are giving it. these things are best run hard. I'd like to see how you are progressing with this.

Some oil in the burner at startup will help get it lit faster. this will come up in a couple of minutes if you give it more oil and air. Your design layout is good. Oil consumption is directly related to heat output. People seem to think these things are like a car and can be more efficient but not the case. Running the glowing is where you want to be. You can back the air down with the fuel to get a greater turndown ratio but they will have a happy place depending on the inlet size with air speed as well as the chamber size. If you want to run this stand alone or for hours, use a pump and a timer. I run mine all day and night to heat the house and the timer / pump keep it constant wherever I set it. At 1L of oil in 30 Min you were producing about 20KWh. Getting below 1L an hour is difficult. A pump allows you to measure flow and from there you can work out how many seconds min pumping you need and set the output. You have set this out very well.

Great job! yes, the hotter it gets the more oil it guzzles and that is a pretty powerful setup you have there. Oil burner the aussie guy had such a setup and managed 600 kilowatts! All he had was a bigger blower!

You could hook up an oil barrel as a hot water storage container. 45 imperial gallons of boiling water in no time, if the tank were insulated you could have hot water for at least 3 days.😂

You are only getting about 2-3 kilowatts of burn power there at the drip rate you have. The pipe from the blower does not need to be reduced, just a straight pipe from blower to furnace with the drip tube as it is. Yes you could do with a more adjustable valve. The blower is good for around 30 kilowatts so should be plenty. You don't need the petrol blower. 10 kilowatts for every litre per hour burned is an approximate for these systems.

nice work mate

ME GUSTÓ MUCHO!!!

The long pipe is too small and it needs more oil

I'm doing the same, what's your best electrode combination.

Great work - I appreciate the efforts and research! - nice keyboard btw lol

So, electrolyte stirring yields best results? - a stirrer?

You speak a lot

i just watched this on the meta quest 3 on a screen as big as shipping container. you were only uploading in 720p but it looked like 4k. unbeleivable !

Careful, if you produce too much power, you might make the " *PERFECT* "cell sorry I felt like I needed to

nicely done! Have you 'flame tested' the carbon felt you've made?

I dont know what happend but good luck, keep the good effort

مرحبا بك يا سيد دان ااذا كنت مهتما لعمل هذه البطارية . سوف اخبرك واذا كنت تستخدم القطب الموجب قطعة من الجرافيت اضيف الي جانبة قطعة من لباد الكربون سوف تحصل علي مساحة سطح اكبر . واذا كنت مهتما سوف اخبرك لاحقا كيف تزيد الامبير الي 4000مللي امبير للخلية الواحده .

Good one Dan . I am interested in doing a iodine zinc cell soon . Should be interesting . I am trying to find terracotta tiles but flat sections but I might just have to use pots .

Hi Dan, interesting experiment thanks for sharing.

Congrats man idk why I’m here but the algorithm brought me here at 2am

I don’t understand a single thing but stay safe and i hope it ends well 😭