Видео

Perhaps you were looking for a video about simple setup of FB36 with Rockwell? A 6 minute video video more suitable for this can be found at this link-> ruclips.net/video/BzgT0G6AJb4/видео.html. The "QuickConnect" (Prioritized start-up) technology feature refers to a method of establishing a connection between devices and the Master in a rapid and efficient manner (example: robot end of arm tooling). This is a ODVA EtherNet/IP specification where a device shall have this feature disabled as the factory default. Due to the requirements and effort of the ODVA spec to configure a device for "QuickConnect" I created this video and the sample code to compliment it. Once you have viewed and understand the concept and requirements to configure the FB36 for QuickConnect in video, the sample code can be used to accelerate the user efforts. I think it would take approximately 5 minutes to configure a device for QuickConnect with the sample code provided. If a user had good understanding of the configration requirements from ODVA spec, they could use software like Molex instead of Rockwell and likely setup a device in even less time.

Sorry for soo late a reply. The operational mode is changed via the digital inputs. You can find this in the user manual or contact local technical support staff at Festo.

No idea - I did this video long ago and I have never used a BNI004F

Unusual because this is normnally very straight forward. Hard to troubleshoot on YoutTube and I dont provide support here. Rockwell has bug with EDS AOP on old RS5000 versions, so, I can suggest goto webpage & confirm IO size, delete existing EDS AOP, Add again, select fixed size with hard set IO - do NOT chnage this config after accepted and closed (this is the Rockwell bug). If that doesn't work, try generic module and same method use correct instances -> I think from my memory 101,100,102 with exact IO size. If nothing works, contact Festo technical local support

I don't understand what you are talking about?

This video is about the Festo VPPM - not IFM. Messaging of IO-link master will be different for every device especially vendor specific parameters. I suggest you Read the owner manual of the IFM and also the 8IOL to find answers.

Hmm. SPC200 was phased out I think in 2015, so, I would look at why you are still using this - you could get yourself into a situation where you cannot even find any old parts lying around. To you problem - I am not technical support for the product, but, considering it is NOT supported any more, I suppose this is why you try me in the 1st place. The error is not mentioned in the user manuals, but if it says the axis doesn't exist and you have physical hardware, then you have a problem with the hardware and it thinks it really doesn't exist. A good way to determine hardware configuration of ACTUAL controller is to start with empty project, then Select the menu item “Upload” then “Project”. Select a Project path and give it a title name if desired, then save the project to you hard drive. When the upload is complete, the project will be open and you can see what the controller sees as its configuration. This is all I can do for you.

Another point from my side - If the SPC200 hardware for 2 axes exists, BUT, the connected axis cylinder (e.g. DGPIL) has an issue or is NOT connected, then I would also expect the same error you have encountered. Good luck

Sorry I missed this comment soo long ago. For your questions, there is a video FCT Backup or Archivate Projects at this link -> ruclips.net/video/scQ7zG5OwuU/видео.html

Welcome

Sorry for long response time - I was on vacation for last 6 weeks. to use the FestoMotionFHPP library Modbus FBs, there is no license required with S7-1500

😂👍 hope your a subscriber 👍😂

@@Proud2BProud heck I am now! Lol 😂

Thats i nice size project! I can imagine running out of memory quick. This is an older project so little hard to remember if possible right now, but, there should be a AOI called single param or similar. With this you can read or write single parameters. I think there is also an AOI in the library called multi param or similarly. Here u can set up an array of all parameters you need to a limit. This forum not best for this request though- hope i give u some ideas. You should contact your local support and mention what I offer and if you don’t get anywhere, Ask them to escalate.

When you download the library there will be user manual which explains all the AOIs in it. There should even be examples if i recall

Did that help?

The AOIs I referred to previously are called: FPC_MULTI.L5X and FPC_PNU.L5X

I added navigation to the RUclips video for you - when you SHOW MORE, you can click on the link for (32:08) and navigate direct to the section that details the AOI

The Festo website has a good source for STO with EMCA in the downloads area. STO is basically the same for EMCA as it is for CMMT-ST. In the expert area, a download of www.festo.com/net/en-ca_ca/SupportPortal/Downloads/598918/653211/100244-TS-Application-Note-EN-Ver1.pdf and also www.festo.com/net/en-ca_ca/SupportPortal/Downloads/598917/653209/100242-TS-Application-Note-EN-Ver1.pdf can be downloaded. In the Documents area, brief instructions for Safety can also be found

I always prefer SS1-t - this is much better safety coverage

@@Proud2BProud yo awesome man. Appreciate the help! This is my first time in 8 years ever having to deal with this festo motor. So it’s all new! Thank you so much!! Crazy you replied after how old this video is!!

I don't know - perhaps check the balluff website where the AOI originated.

Thanks you

Download of the hardware configuration is only necessary

I do not support technical questions for my personal video’s - I hardly have time to make them. Please contact your local technical support with questions about your applications.

If you encounter a problem I suggest you read the user manual or contact technical support. Sorry, however, these are my personal videos and I am not support for everyone who watches them.

I suggest you call technical support

I suggest you contact Festo Tech support at your location and they will surely help you. You might find some modbus function blocks on their website that works with 1200 as well.

Sorry but don’t have that. I suggest you contact Festo technical support and ask them

No hmi related material to offer

Sorry for that - Yes very late reply and in my earlier days of RUclips. I hope my newer content is more helpful.

My computer is down at moment

I’ll try again

Normally I don’t respond to comments because far to busy all the time

I have never attached any file to anything on RUclips and at moment cannot see how

sorry

Safety tool is for setup of the Safety module installed. This comment area is not for support for you. Please contact Festo technical support for Troublshooting.

This RUclips video for CMMP + CPU1500 should be very close for CMMO-ST-LKP + CPU1200 - give it a try !

Thanks

Alrazy Sonet Thanks but my name is Steven

@@Proud2BProud My bad, I guess autocorrect in my phone probably did that. Sorry about that. Now corrected.

Thanks

Sasti Kumar Hello, I have not shown a ring network because to configure any DLR network is just a checkbox on supervisor and very simple. So, in general, you physically connect entire ring and leave 1 cable disconnected. Next, in supervisor on network tab, check “enable supervisor”. Next, physically connect cable that you left off. Next, in supervisor, click button to clear ring faults. Ya dah!You now have a working DLR network. Enjoy!

@@Proud2BProud that's easy. Thanks.

Could you make a videos about spu card of omron

Sorry but not interested in that concept

Muhammad Numan Anything I shared is already at the link in the text below the video

Thanks

Hello Jonathan, my videos are made in my private time and are for the public and are meant to help people without my intervention. I expect people to handle encountered issues by themselves. I do NOT have the time or capacity to provide support to any of my videos through RUclips or through a direct way via email or phone. If you have an issue with a Festo product, then please contact their technical support and please do the same for the PLC manufacturer if you have an issue with their product.

Thanks

Your Google translation to English: They will have a channel to see more about this type of programming to see how to handle these FAS blocks through a CDPX HMI to interact with the operator. and see where the tags are stored to program..... My Response: perhaps the translation is not accurate and you are asking a question? Are you asking if I will do another video to show the CDPX interaction with the Festo_PtP_Base Library Function blocks? If this is your question - I am not planning this and am far too busy traveling for work and pleasure at the moment. Regardless, the CDPX is separate software from CoDeSys and the visu libraries included with this Festo_PtP_Base Library are specifically created for CoDeSys. If you want the same look and feel for Designer Studio/CDPX you would have to create them yourself.

@@Proud2BProud thanks for your answer

Thanks

Aaron Felonia If you are talking about the CTEU-EC EtherCAT module?

Aaron Felonia if you want to Connect to an Ethernet/Ip master then you need to buy the CTEU-EP module

Aaron Felonia for further questions please contact technical support. My account is private and not intended to answer questions

@@Proud2BProud yeah that's what I thought too. But client a bit know-it-all, yah know Anyway, thank you very much for your reply! 😁

Make certain the client wasn't talking about EoE which is a Mailbox protocol which tunnels standard Ethernet communication over EtherCAT. In the most cases you use EoE to have access to the webserver of a device. To update a FW you use FoE (File of EtherCAT) CTEU-EC has a webserver

Hello, I don’t normally answer questions on my RUclips because it is all my personal time, BUT, to me it would make more sense to use a ProfiNet node FB37 as this is the native Siemens protocol. Why are u thinking about modbus which is easily inferior. Did you buy fb36 by accident? If you had to use the Fb36, it is capable of ModbusTCP and I know the TiA portal offers some mod us FBs, I just haven’t done this myself because it’s not something that would be very common and therefore not worth my time investment.

@@Proud2BProud why u put then video's on youtube if you are not ready to share your knowlegde??

@@morrocantocador The video is sharing my knowledge on the topic I have explained within it. The FB36 is capable of ModbusTCP, so if your V13 TIA is, then it would be possible, but, I would recommend using a CPX-FB33 ProfiNet as the head module instead of the FB36 and this way you have real-time communication.

The CECC-LK has a CANopen Master. So, I would say it should be very possible to add a CANopen-IO-Link Master from another mfg to do what you are asking

Thank you for the quick answer! that would be possible of course.

Your Welcome

Abderahim Ennejjai I am not in habit of answering requests nor do i usually answer questions on my channel. Everything I do on my channel is on my personal time after work and I hardly have the time for that.

There is no way to simulate any hardware connected to CANopen that I know of. If you find something let me know

I don't understand your comment. The video content I post shows how to do specific things. I do all of these on my own personal time after work. This video comment description Is for what it indicates. I do not take requests on making other videos nor do I provide support via RUclips.

Thank you

Thanks

Keep looking - watch the video - download the sample code - you can do it - I have faith in you.

Hello Jerome, I don't normally converse on my channel because I hardly have the time to create the videos and so don't expect to support them. In your case, I do NOT understand your question. The address for the raw process data is %IW1, which is found when you double click the sensor on channel 0 of the IO-Link master. Further, you click the IO-Link I/O mapping tab and expand the PDV(InA). If you look in the GVL, you will also find I mapped the %IW1 to a tag.

Nothing magic - i just typed them in.

Starting from left to right and using tabs where needed

I don't know what a panel mobile 277 iwlan is nor do i support people on RUclips - I wish you good luck