Видео

Thank you i just fixed my generator with this video 😊

Great help. Very informative video. Thanks a bunch.

Thanks you. I do it today but no was so easy. I see why now.

I have this problem, but I cannot remove the screw even after using penetrating fluid and if I keep trying I will just strip the head. Not sure what to do.

Thanks!

Really great video. Helped me a bunch!

Thanks for the video. My 20 year old 1000 wouldn't start, and watching this video helped me out. My carburetor pulled straight out to the side, so I didn't have to remove the studs. The needle valve was stuck, and after cleaning everything, it started right up and idles like new.

I hate this generator, there pretty much junk!

nice work

Thanks for the Video Got mine Fix with it

I have this same model. They are super reliable . I use 93 Shell VPower for gas. Every year plug and oil change. I just wash the filter . It starts every year! Ive had Toros and other brands ....messed up my shoulder with those.

This is an older video, but the screw you removed from the carburetor is totally seized. I tried everything to get it out, just going to buy a new one on Amazon

Thanks. No, go.

On the studs.1 threaded part is longer and the other side is shorter on threaded..which side goes towards the motor?

Snapped the shaft trying this 😢

My float fell off and a pin came out from underneath. Had to slide it in a Slot on the float.

hi mine got wires its an inverter wen.. :(

"Honda, I am your father." 😂

3 years old Happy Birthday!! and still saving us in 2024!! I just put my yammy back together . It was only running with the choke full on, LOL I actually modified i small rubber hose to keep the choke throttle all the way out. Now it runs with the choke off yea!! but now I am surging, rats!! At least after seeing this video I dont have to do a complete removal of the tupperware. Intresting thing is my pilot (idle) jet doe not seem to have a hole in the bottom, but all the videos show there is on. I even looked with a magnifying glass, curse my old eyes. Oh well here we go again.

Worked perfectly! Surge is gone, fires right up, plus I adjusted the low idle speed. Thanks for posting.

where can i buy an ef2000 carb ? most come with a square servo connector.

Where can I buy the studs?

Great video I Appreciate it now my mower runs again.

Fishing line works great, and won’t scuff the bronze.

Thank yous for posting videos and those lawnmower makers...

I know this is an old post..but it just saved me a new carb for a my Honda. Great video, and one of the best parts about it was reassembling the carb....I would've struggled had I not seen this. Thanks!

Thanks for the great detailed video

Nice tip for getting the carb studs out, thanks for that!

Do not store this generator with gas in the carb. Drain the carb, and you will have no problem starting it next time you need to use it.

Thank you so much for this video. I had to stop the video quite a few times to catch up with you but was able to remove and clean my carburetor successfully. It now runs like brand new. Thank you for the great instructions. Priscilla

Excellent, will try it .

My Honda lawnmower sat all winter and I started it up and it died within seconds. I followed your steps to the T and guess what? The lawnmower runs like it's brand new! Thank you so much. Very easy to follow and great results.

Nice work brother. thumbs up. the q tip polish in the needle port was a nice touch. the only picky part i could find was you didn't snug slight twist the fuel bowel to you feel a natural solid seat on the gasket Hold in place with slight hand grip and bring the bolt up to grip before releasing the hand pressure before tightening Heheh. nothing worse then a leaky fuel bowel after assembly. Great job brother

My tank is full, do I have to drain it first of are there any tricks to keep it from escaping from hose .

Got the same model with carb bolts facing out instaed , i will try same method other than that . Thank you.

TOTALLY BAD IDEA, this is a hack method and it resulted in me stripping one of the carb shafts. The first one came out ok, the 2nd shaft stripped, now I need to send for parts. Please remove this video from RUclips.

Video was great but I could barely hear the audio. Also, you forgot to show reconnecting the fuel line during the reassembly.

Great video but I snapped one of the carb bolt stud while trying to remove the carb. Any idea what the replacement part number is?

Very helpful. Thank you 🙏

The Harbor Freight Predator 2000W Inverter Generator looks like a clone of the Yamaha. This helped me fix the idle circuit on the carb. Thanks

Great tip on removing the Carb!

Thank you so much for this vid! I had stripped the bottom two bolts preventing me from removing the entire case then the carb. But thanks to your awesome vid carb removal is so easy! Thank you again!

I was looking for a lightweight blower for my deck. ruclips.net/user/postUgkxgioZQl3J5wPGAeDINzbieKbT5qomSEx3 There are some huge trees around my house and the leaves and pods drop all over my deck. Having to move furniture around to sweep has become too big a chore. This blower was the answer. It is light enough for this 70yr old lady and powerful enough to blow all the tree droppings off my rather large deck. Thank you B&D. Be aware the cord is not included. I use a 3 prong outdoor cord 25' cord for my 12' x 20' deck. The cord retainer works very well, but don't try to pass the plug through it. That is NOT how it works. You just have to loop the cord and it works great. One of my best purchases. Very happy.

Love this lawnmower ruclips.net/user/postUgkxTPN04aT-Qdjr_KS3ql7ng8wnU3wwsCqk also recommend although it has a smaller cut in the grass it's easy to maneuver and very lightweight, would highly recommend for somebody older that lives on their own and has to cut their lawn.

Awesome video and great info. Were you able to reuse the old gaskets? Are replacements available if they get damaged?

Thank you for the video. I order parts today and will be installing on our Predator 8750 gen. You may have but didn't show inline fuses to the relay and actuator. I'll add 2 fuses. I don't want to burn down my generator with these inexpensive parts. I'm going to see if I can wire the 4th relay to the throttle ECS. I'd like to start with the ECS off, then turn it on. Like someone said, adding an on/off switch for the relays/actuator as well. Thanks again for you videos.

Great video! I got both of my EF2000iS generators running again. I have older model gennys and couldn't get the emulsion tubes out but they are running great now anyway. Thanks for the tutorial!

Thank you! My low hour ef2000is is running like garbage unless i keep full choke on. While this was more than i expected to get a carb off and clean it i appreciate the video. I'll probably be trying this sometime this weekend so i can hopefully run my AC unit offgrid in a couple weeks while i get my solar power system setup.

Excellent video. To the point. No dog, child or wife..

Great job on this tutorial, my 2009 ef2000is does not have the emulsion tube that can be unscrewed out of the carb there is no slot for the flathead screwdriver. Have you seen this before? Is there a way to remove it?