Видео

Small nail or wire. Something that can fit inside the roll pin that you can bend you can hook them under and pull them out. But like I said if you can get the hop up out with the inner and you can pretty much punch them out

@@douglassoal6196 I mean yes the first few runs of nozzles were weak but I cover that and how I modified it. Also I haven’t really had any issues with co2 mags. I had some feeding issues but cleaned out the bb channel and made sure there was no debris and now they have been feeding just fine.

@@beric2173 sorry to say but it’s been sold a while. If you just wanted a static model I’d recommend just getting the aeg version. It will be cheaper as the gbbr one is about $500 I think and this Daytona one was probably about $1k to build.

@@gbbrworld4759 All good appreciate it a lot

@@ÉmileGosselin-b4j HELL YEH BROTHUR

@@davidem8215 sorry don’t quite understand your comment but I did recently install the new maple leaf hop up and inner and have had no issue so far with co2 mags

@gbbrworld4759 i've had also installed maple leaf chamber but after 1 mag on co2, the maple leaf broken on fixing barrel.. the force of recoil just cut off the fixing and the barrel come out.. similar at happened to you previous.

Doesn’t use a clip system so there’s no empty clip to eject on empty

@@DataLog it performs better in colder weather, stronger recoil and cycles faster. The fps is still the same as running greengas. It actually might be shooting lower fps than greengas

You can’t unless someone is selling theirs used with the attachments you want

3mm

Thanks you 🙏 ps was it expensive? 🤔 Because I'm debating on just getting the gen5

@@Airsoft_Nomad gen 5 won’t have steel slide. Only aluminum. But yes the gen 3 steel was so worth it

@@gbbrworld4759 true It won't have the steel slide but if it's too expensive to do the RMR cut on the steel slide it's kind of worth it to get the aluminum one since it's already has the cut haha 😂 itss just 50% less Realistic haha haha

@@Airsoft_Nomad the rmr cut only cost me like $150. Also mos yes is factory cut but you’ll need to use an adapter plate which only has cons, one: there’s the plate and it’s hardware that can potentially fail, two those extra parts can also loosen and lose zero, three the adapter plate adds height to the optic vs a direct rmr (or whatever cut you want for your optic of choice) which allows the optic to sit lower which means less height over bore, easier sight alignment and even though it’s not a lot further down it’s still further down so the fulcrum point of “recoil” is lower and more straight back. (This isn’t much for airsoft but don’t see how it won’t help either lol)

I do just rarely.

Just trying my best with my busy life. Hopefully post more soon. Glad you got a krink. I sadly sold mine to fund other things but that’s one I miss a lot.

Yeah I have a somogear now too. Just nothing beats reliability and piece of mind of having a real one. I mean for Airsoft doesn’t really matter but outside of airsoft idk if I would absolutely trust my somogear one. Maybe for sub 100yd shooting

@@gbbrworld4759 yeah ivd run mine on real steel to good result… but I’m sure that could very easily be a case by case situation… still fun running ir w nods at night like super fun

@@gbbrworld4759 so question the barrel nut on that gun is just a normal barrel nut that’ll work with any normal rail and sale w front sight post on outer barrel it’s easily removable correct? Thinking about buying this gun and putting a 14.5 ris on it and making internal mods to do a dmr that will kinda look like s long mk18… I know ghk sells that gun already made up.. but I can buy this gun you have at a deal right now and then spend the rest of the difference on all the upgrades… just want to make sure I’m not getting myself into a situation that’s not worth the two dollars I save… more about building a rifle.. but either way I have to do the same internal job

@@johndaviddoesmith4504 this barrel nut/delta ring only works with the kac RAS rail system or the plastic hand guards. There might be other rails made to fit between the FSP and delta ring but not sure. Most rails usually come with their own barrel nut for their specific rails. So if you wanted to get a new outer you’d need to get new rails and barrel nut. Like for a mk18 with Daniel defense RIS II rails those come with their own barrel nut and don’t need a FSP since it’s free float rail. But yeah if you find a good deal on a ghk get it and then you can order the barrel and barrel nut/rail you want

@@gbbrworld4759 yeah it’s a pretty good deal… but close enough by the time I buy the dd 14.5” ris, if I have to buy a new outer barrel etc .. by the time I’m done doing all that I could just about buy the ghk 14.5 ris already assembled… so it’s close enough that it’s real questionable… feel me..?.. honestly I’ll probably just spend the extra hundred two hundred bucks and get it built the way I want it from factory, know it’s new and everything is right… and build out from there… and yeah I have a ghk mk18 gbbr fully modded it’s a great gun

Hi. Sorry I don’t really take on orders anymore. Too busy and I also do t have a we m14 or my custom m1 garand anymore to test said mag

@@gbbrworld4759 ahh, ok, just wondering, what aeg barrel did you use to replace the m14 barrel?

@@minisutart4570 I used a gbb inner barrel and I used a mix of the gbb outer and aeg

@@gbbrworld4759 was the outer barrel part an ics outer barrel?

@@minisutart4570 yes. I used both the outers from ics and we. I should have a vid of the full build you can reference

It’s 3mm deep cut with the holes for the rmr being 5mm deep. If you want find my posts in the ghk ghk g17 FB group and send me a message so I can send the blueprints

​@@gbbrworld4759 Ok, no problem

Can I get the fb link to see your blueprint?😢

No. Super high quality finish on it

Sadly I don’t think they make it anymore. I’ve been asked so many times and haven’t been able to find one

Still on Ali express, just ordered one myself

Still going. I swapped many co2 parts from a ef co2 g34

Safariland 6354DO for g34 with x300

I sent the slide to be rmr cut. It’s not just drilled. It’s also cut into the slide

@@gbbrworld4759 Thank you for the reply, I meant the drill bit you stuck inside the nozzle arm

@@alexal1232 ohhh I used a cheap black oxide type of drill bit.

@@gbbrworld4759 understood, thank you

Yes. The steel kit only changes the externals. The internals are still the same so performance and functionality are exactly the same as standard body.

@@gbbrworld4759 i asked because producer claim the power source should be low pressure gas HFC134A, and i was wondering if the steel kit change something in terms of that, but i guess not if internels stays same. If you remember please tell me one more thing about this kit, there was some stock wobbling on any of segments? Or everything sturdy?

@@SWJarek all stock internals. The steel kit just replaced the receiver shells. The stock was about the same if not a bit more sturdy but not like rock solid

Which lower. If you have a gen 5 lower it fits right on. Only reason mine took so much work was because it was making it with ef co2 mags. If you’re just using green gas it’s drop in no custom modifying needed. It’s a safariland 6354DO for g34 and x300 light

The slide was milled and drilled for the rmr almost like a real rmr cut on a real pistol.

It’s still running and reliable as hell. Daytona kit was about $550 usd. I got the m240b for cheap since it wasn’t working

That acog is just a replica. I have a real trijicon rmr on my ghk Glock

No it’s a we m14 and ics m1 garand mashed up

Yeah it was more over view/instructional

Sorry no. This post was for the buyer

Dang its a beautiful gun

@@nicholasclouse5698 yeah I miss it a lot

Think youll do another daytona m240?

@@nicholasclouse5698 maybe. There are still ways to get m240 bodies and even heard rumors there’s a company going to make them again

It is a echo 1 Ohio ordnance licensed version but pretty much all m240 replicas are based off the same design.

Thank you for your answer! This replica is out of stock every where. S&T is still available im few shops but I heard it request extensive modifications for a Daytona kit! Do you know if it’s true?

Same question for the Matrix M240 ar evike. That one is available.

@@cedleced from what I’ve heard is that they all pretty much are copies of one airsoft model from years ago

It’s ghk 12g co2 mag and the red dot is a real trijicon rmr rm06 3.25MOA led adjustable red dot

Is the nozzle okay? Sounds like maybe the nozzle might be broken.

You can but not recommended. The co2 kit comes with new nozzle to help regulate the higher pressure co2. Also the recoil spring and guide rod is stiffer to also handle the faster and harder kick. They also include a new hop up/inner which idk why but it’s beefier than green gas

@@gbbrworld4759 ah ok thanks. Are the modifications hard to make if you don‘t have any experience with modifying airsofts?

@@harald2101 samoon has co2 conversion kit and I’ve installed a couple. Takes like 15 mins. And yes I do. I do lots of gbb tech work

@@gbbrworld4759 sorry to bother again, but what is this kit called exactly? i found the "enhanced kit" and the "ultimate kit". here in germany it costs about 200€. that can't bve right, can it?

@@harald2101 the co2 conversion kit is called ultimate kit. And yeah it’s a bit expensive but comes with a lot of tougher made parts.

USA

It’s a real trijicon rmr rm06

I know. Just require some modification to run smoothly

@@gbbrworld4759 You still playing?

@@RazorNLD I still do. Not so much though.

@@gbbrworld4759 Alright, dude! I am thinking of buying one of those G&P Kits too. Do I need to have alot of tools for this or will a simple screwdriver and wrench work?

@@RazorNLD a good ar wrench will really help but my first one I built with a small Allen key set, channel lock pliers, regualr needle nose pliers and basic screw drivers