Видео

This Stuff Works !

Hows the gasket holding up???

Is this the actuator for the temperature?

So how do you move it up/down,do you have to loosen the bolts on the side first then turn the middle bolt for up or down or can the it move with the side bolts tightened ?

Whats the oil capacity, I see just a jug of oil and it is supposed to get 5.7qts of oil!

Did you un screw the bolts before you popped it off?

👍👍👍♥️♥️♥️♥️👋👋👋😊😊😊🌹🌹🌹

Is the black finish version as good as this one?

Any update, did you end up installing ?

What is the difference between these and the Cobra's?

Would love to see a follow up video- how do they wear, what are your thoughts after several months of use?

I watched a bunch of these videos. They made it look easy. "Bullcrap". it was the biggest pain in the ass i have ever worked on. I even had the flex ratchet tool. You just can't get your hand back in there to get any leverage. And everything is in the way. Putting back in was even harder took me even longer. Becuase it has to line up right. I also ripped my hands open a bunch of times. This is the worst F**king design i have ever seen. After fighting with just two bolts, I Finally got mine out almost 2 hours later and It was still working fine when i tested it. Good thing too because The new part I bought from amazon for $28 ,Didn't even work. I tested both parts to see if it would work better. Man would i have been pissed. It would have been faster to just take the whole dash out. Becuase that way if actuator isn't broken, it's likely the heater core is plugged. Or its a broken blend door. Either way. At least you can replace any other faulty part right away while dash is all apart. So now i'm doing a rad flush and try to reverse flush the core at the same time. Hopefully that works. If not that means the core is pouched. Then it will be another 4 or 5 hour job.

Yes, it helps. Thank you for the video.

🎯thank you

What year is this?

Ordered some grey 8" forefronts. Can't wait to get them. That grey looks so clean. Have a black pair with safety toe and I love them. Bet the grey ones will look even better.

besides that fuckin bolt on the bottom of the blower motor fuckkk thaaa bolttt omffggg bout shot my brains out

Good job! That’s what I was looking for.

Dude, I appreciate your video. You made it easy

From my experience... All the jb wraps I've used have smoked a bit and stank for a few weeks if not months. (But worked when applied correctly. It's a bandage not a cure.... save up and get the proper flex pipe. You can fix that pipe all you want but without the flex pipe in the exhaust by the engine it will keep breaking no matter what you do... the engine sits in rubber bushings guys, when it starts or you accelerate they squish and the engine moves around in the bay. It stops from vibrating the rest of the vehicles bolts out of everything and makes the ride more comfortable. So the exhaust needs that bendy piece if pipe to keep from snapping the exhaust every time you start it or hit the gas. Be aware that any paste or wrap needs to be rated far over 1000°f if the break is near the engine or behind a catalytic converter (the games react with the metal cat and actually set the fumes back on fire to burn off harmful vapors, it emits less toxins that way ) breaks near or before sensors will ruin your fuel economy and make your engine run dirty by not getting proper air readings to see if the fuel is burning off properly. Hope this helps everyone still keeping the necessity cars running. Exhaust leaks mess up air fuel ratio and it either gets too much air or fuel, both problems wear out and gunk up your internal bits and shorten your cars lifespan.

Looks like Gary on SpongeBob!

😦

Awesome. How do I install the seat now?

Thank you, I’ve ruined my fingers trying to find an anchor inside the seat.. so frustrated! I tried everything, til I desperately went to see if anyone figured it out. Almost gave up if it wasn’t for you! Thank you! Thank you!

Thank you !! I'm doin any moment and have tried several times to figure out the anchor situation. Soo blessed you put this video up 🙏

Does it smoke for a while after??

I didn't know they offered that as a tool set. I do wish the sockets we’re standing up. would save more space in the foam tray like Snap On and icons set up.

McDonald water taste gross

Just bought the same just 4” setback. Hope it works out for you👌🏽

You should really try to do a better job. It really sucked to click on your link and see that you couldn’t even get it to work.

Thanks works perfect for my apartments!! I have a 2018 camry

Aren’t you suppose to wet the surface first?

i got all 3 cobras wrench and twin ! its the last pliers ull ever need !!

Thank you so much! I looked everywhere for the LATCH bars so its not just you. (The manual didn't help anyway)

dumb shit video

My car is giving me a slow flashing orange light when I push it not a green light

Great video. Thanks brother 👍

THANK YOU!!!

I keep the micro cobra line pliers in a knife sheath on my belt,they have saved me many times. I am an electrical Overhead lineman and keep two of the cobra 250’s(10 inch) on my climbing belt, the capacity of the jaws are incredible and the gripping power cannot be beat,especially with our rubber gloves on. The plier wrenches as described are just phenomenal. The twin grips are a great addition also. Just don’t lay any of them down without keeping an eye on them as they will grow legs.

this one it's more expensive than the cobra, i need them XD more usable on bolts and nuts without damaging them like the cobras, really cool pliers and useful, thanks for the included examples 😁😃

The Knipex Twingrip pliers are my edc. They're like if Knipex saw what Vampliers did and said, "let's make those, but adjustable" and they did. If the Twingrips weren't adjustable, your Knipex would be my edc. I keep your knipex pliers in my work backpack along with my Irwin Vise-Grip model 4LW (strange looking vise grips but perfectly built).

Hey dude.. really like your homemade multitool...gives me an idee..

Wow we spent time doing the same thing. Turned to trusty you tube. Success thanks to you. The manual is horrible as well. Thank you.

Thank you so much! Your video helped us!

Did it fix the issue? If it still worked on high it was probably just the resistor that was the problem.

So you just put jb weld sealer on and even stated I really want to let it cure for 24 hours!! That's good but then the first time you drive it you got the engine up to 7,000 RPM !! And you thought o it should be fine!?? That has to be one of the Stupidest things I have ever heard from a person claiming to know what they are doing working on cars to instruct people on ! I Don't even let my vehicle go past 2.500 rpms I try to only let it go slightly above the 2,000 mark for at least 2 days because of the fuckin pressure and fully cured time Jackass!!

Does the systems over heat

The lifetime replacement is almost worthless. According to the website, returns require an original receipt.

26 oz

You don’t have to get the cup. Just ask them to fill it up. Same with the bucks.