- Видео 40
- Просмотров 307 870
Hodge Garage
Добавлен 2 окт 2013
90HP Mercury Carb Work
This engine is from 1988, but I'm sure this is video will be helpful to other models.
Просмотров: 62
Видео
Lug nut keeps spinning, but not stud
Просмотров 674 месяца назад
The lug nut kept spinning but the stud was not spinning. There are a lot of videos about what to do if the stud is spinning, but this was not my case. Pretty sure this was caused from someone cross threading the lug onto the stud.
2013 Toyota Highlander 2.7l PCV Valve
Просмотров 1,3 тыс.4 месяца назад
Having trouble locating the PCV valve on the Toyota 2.7l? I'll show you in this video where it's at and how to replace it. Please like and subscribe if this video helped!
Zero Turn Blade Replacement
Просмотров 1345 месяцев назад
Changing the mower blades on my Big Dog Stout.
03 Mazda Alternator Replacement
Просмотров 7866 месяцев назад
Replacing the alternator on a 2.0L 2003 Mazda Protégé. The dash battery light was turning on and then turning off after driving ten or so miles. This repair fixed the problem.
09 Silverado CV joint not cooperating
Просмотров 528 месяцев назад
CV joint kept coming loose when replacing CV axles. If you have a leveled or lifted truck, this should save you some time.
09 Silverado Throttle Body Position Sensor Replacement
Просмотров 33310 месяцев назад
Changed the throttle body position sensor on my 09 Silverado. This was an attempt to solve a transmission issue that I've been experiencing. This did not solve the transmission issue, but does show how to do the sensor replacement.
'09 Silverado P0449 EVAP Vent Solenoid and Filter
Просмотров 3,1 тыс.11 месяцев назад
Replacing the vent/valve solenoid on the '09 Silverado. I also show the location of the filter that comes with most replacement kits.
'09 Silverado P0106 MAP sensor replacement
Просмотров 10 тыс.11 месяцев назад
Replacing the MAP sensor on an '09 Silverado after getting a P0106 code. This repair solved the problem.
09 Silverado Tailgate Won't Open
Просмотров 66Год назад
Tailgate wouldn't open, took it apart and found the problem.
Installing airless zero turn front tires
Просмотров 634Год назад
Installing airless zero turn front tires
09 Camry Valve Cover Gasket Replacement
Просмотров 6 тыс.Год назад
09 Camry Valve Cover Gasket Replacement
'09 Silverado Service Four Wheel Drive Fix
Просмотров 53 тыс.Год назад
'09 Silverado Service Four Wheel Drive Fix
'09 Silverado Upper Control Arm and Inner Tie Rod Replacement
Просмотров 5552 года назад
'09 Silverado Upper Control Arm and Inner Tie Rod Replacement
09 Silverado Cold Air Intake and Throttle Body Spacer Install
Просмотров 2,9 тыс.3 года назад
09 Silverado Cold Air Intake and Throttle Body Spacer Install
DIY No Sewing Boat Seat Reupholstry
Просмотров 31 тыс.3 года назад
DIY No Sewing Boat Seat Reupholstry
'09 Silverado P0521 Oil Pressure Sensor
Просмотров 33 тыс.3 года назад
'09 Silverado P0521 Oil Pressure Sensor
09 Silverado rear brakes without disconnecting e-brake
Просмотров 984 года назад
09 Silverado rear brakes without disconnecting e-brake
How do you bleed the air I’m comfused
My it's a 2017 and it's in the same location!! Thanks
Can you tell me where it goes connect the hose it's going to the engine direccion..?? My hose is cut and i can find the other end....
It should be on top of the transmission or transfer case.
I just did this for my Chevy Silverado 2500 HD 2012 4x4 works like new now !!!!!!!
Boss what about codes? After scanning does your vehicle throw any codes?
It didn't throw any codes
Im pretty sure i no what the dealership done to it see when u took that shift coder motor off the one that came with the truck you herard something fall inside the transfer case that fell n low lock and when u baught the new shift coder motor the new ones come n neutral thats why when u put the new one n the red light was on because the new shift coder motor came in neutral but your transfer case fell n low lock so what you should have done was before u put the new shift coder motor on you should have connected the new coder motor to the plug n without it put n the transfer case then turned it to low lock that way the new coder motor was n low lock when u put it n to line the shift coder motor up with low lock the shift coder motor has to b lined up with the transfer case gear inside the transfer case if the coder motor is n neutral and the transfer case is fell into low lock it wont work right because the coder motor isnt lined up with the transfer case low lock gear its n
curious if the pcv valve change fixed the oil burning issue?
Unfortunately, it did not. I think the issue has to do with the piston rings.
That sucks@@hodgegarage
Lost audio
Hello I have mazda 323 . I changed the rectifier on my alternator but when i turn on all electrical instruments inside the car light,heater etc. The battery lamp comes on in the dashboard. Should i replace even alternator diode. Because can not hold load and my battery still drain if i let a few days without turn on the car . It is the possible a bad alternator so i have to replaced. Please give me a advice
I would recommend removing the alternator and having a local parts store test it if possible. I usually take mine to AutoZone. If you've replaced the rectifier, the diodes are located in it and thus would have been replaced. If the battery is draining while the car is sitting, it might not be the alternator. You can also remove the negative battery cable while the car is running; if it dies, this would indicate a bad alternator.
PART # HELPS ???
How long is that bolt and what’s the thread on it
Not sure about the threads, but it's about 4-5 inches long. You can use the replacement filter to match a random bolt in your garage.
I heard that if you un plug the module and it's good you will blow the fuse. If it doesn't blow then your module is bad.
I mean't the actuator not the module just so we don't get confused.
Where’d you get that socket? Can’t find it anywhere
Mine came from O'Reilly's
its just a plastic piece they say. just use channel locks to twist it out they say. mine was so **** tight that entire piece broke off. had to take this s**** off, put it in a vice and just like an axle seal had to take it off. what a bonafide pain in the ************************ might want to tell people that its not that easy .
Minute 5:55, went through the same issue
@@hodgegarage yeah i understand that. The thread sealant on mine was so solid had to use flat head screw driver to break loose the thread and plastic pieces. THEN....had to stick screwdriver from other side (taking off diff shaft and while on vice) hammer inside out with small flathead. just waiting for new actuator now. Sadly and initially...my goal was to replace front diff axle seals both sides....after doing so...4x4 is not working...hence this actuator issue. going to just hand tight this with good amount of thread sealant. take it for a drive with potential 4x4. check for leaks again... if leaks then just a quarter turn again. i don't know....
@@alangomes5607 man, that's a bad situation, but sounds like you have a solid plan. Good luck, hope it works!
Why won’t the permanent codes clear,,,, po106 keeps coming back
I would check the wiring harness
could be the throttle body It could be caused by a faulty or dirty MAP sensor, wiring or connection issues, vacuum leaks, clogged or dirty air filters, or a failed PCM or ECM.
Why didn’t your check engine light come on. ?
I replaced it trying to fix another issue.
Hello I did enjoy your video so did you change it because it was shutting off on you like losing power and then it won’t turn on because that’s what I’m having issues on mine ?
Yes, the battery light was on which implied the alternator was bad.
That’s weird because mine was not turning on and it was shutting off on mine. But idk this is driving me crazy
@@carlosjimenez6370 Did you change the alternator and it's still losing power? If it's losing power then it's more than likely bad even without the light. If you need to check it, you can remove the negative battery terminal when the car is running, if the engine stops, the alternator is bad.
@@hodgegarage thank you so much ill do that tomorrow and see how it goes .
Thank you for sharing this!
Great JOB HANNAH!!!
I did this on my 2013 Chevy 5.3 then removed the error code next day code comes back… wth
Awesome video. Doing my struts on my 2010 Silverado tomorrow with the stock suspension. Does the top end of the coil on the new strut face outwards or the bottom end of the new coil
Great question! Most people don't ever consider that it does make a difference. Usually the strut will have a sticker that either needs to face a certain direction. Either way, on a stock setup the top of the coil should face outward.
That thing's the cruise control 🙂
I have an 07 and a 08 Chevy and GMC and I have always had to stop , put the shafter in the neutral positions for it to engage the 4 wheel drive.
Thanks man you followed every step great video….
Cars are made to fail .They make such junk .What happened to quaility automobiles. Auto makers are like governments alway ripping people off.
Factz
📠
Once clip is lifted turn towards radiator then push clip off plastic stud.
Thanks! sorry for breakage .
Should use Acdelco sensor
How do you reset the system? You mentioned it. But I don’t remember what part of the video showed it
Disconnect both battery leads and connect them together. Only the leads connect together, the battery is completely unhooked. Hold those leads together for several minutes, this will drain the ECM in theory causing a reset.
What size is that socket to take the sensor out??🤔
27mm
@@hodgegarage THANK YOU!
Nice job, simple and to the point
Are there two different styles of valve cover for the 09
Not sure
That plastic piece on the back of the engine that blocks your view, can it be cut away? What does it do?
I wouldn't cut it off. The vacuum line for the brake booster runs through it.
@@hodgegarage I would cut away enough just leave that line supported
I'm guessing that would work. You might want to find a picture of the part online first though.
@@hodgegarage Found a good picture yesterday, I already lost one socket in there, my hand just not fitting back there
What does that lolley pop piece of metal do?
'Promo sm'
Check 3 ground wire under the cab that is the problem
Na it’s not tho
For being a child, Hannah did a great job! Moreover, I learned how to repair my boat seats myself, which will save us at least $4,000 if I had the local shop reupholster our seats. Thanks so much for this video!
Glad it saved you money! I'll pass your message onto Hannah as well.
I think I’m dealing with this right now
I hope the video helps!
My truck is manual shifter for the 4/4 on the floor I have low but the high range doesn't work
Not sure on a manual. Might need a new t-case
Thanks for the video! Watch on the side of the road.
on my 2007 chevy suburban 1500 i can hear engaging in and out but still giving me the service 4 wheel
Me too did you ever fix the issue ?
2011 Chevy Silverado 2500hd will be in 2 wheel drive and changes to 4 wheel hi on its own
Not sure, but I would start with electronic components. I haven't heard of that before personally.
@@hodgegarage Thanks, I'll start looking there
🎉
GM should have recalled all the early 2000’s 4 wheel drives. They all have the same issues. Poor design.
Dude I just learned something “ Thanks”
Bravo 👏🏽 .. I’m having the same issue this video got me all siked up and ready to go tackle my service 4WD message issue . Question does the tccm you purchased have to be installed before flashing or could you have taking the tccm to them before installing it yourself ?
Great job. Encouraged me to try on my pontoon when the weather breaks. I think the corner seats will be interesting.
Its always good to have a good diagnostic guy. but now im going to pull my actuator and see what it looks like. Our dealership mechanics worked for food,beer, and money......ha. i admire your patience. im going to check all contacts from knob down. Thanks again.
Which pins do you jump to test the pump
Great job Mr hodge!! I'm proud
What do you mean you had it flash
The dealership has to program it.