Видео

To secure the butterfly fasteners it would be better and more professional to use threadlock. If one of those nuts or screws finds its way into the cylinder it would do a huge amount of damage to the engine.

I don't think the engineer who designed this could have made it more complicated. I removed around 30 screws and still struggled with the airbox lid. Ridiculous . I'm guessing that they hope the consumer just gives up and brings the bike to the stealership

Vidéo très propre simple efficace !

Height of new entire plate stack is 44,36mm, anyone know when to change plates? 1,86mm less qualifies for change or?

throttle body sync , isnt recommended , its a MUST .

What are the symptoms that this rebuilding will fix?

Exultant video

Fantastic good video - Thank you for that :)

Where would I get the soldering stuff from?

Yeah I broke one :(

Can I order them ? If so Amazon has them but idk if they would work

Hi where to set Jack to lift rear axle in one go

Sorry but your video missed something important, the steel plates the one side is different from the other, do you know that? maybe you have done damage allready, if you dont know how is better to go to find someone who knows.

how much do these clutch parts cost? can they be had aftermarket?

My slave cylinder will not sit flush, please help!!

Hello, is there a link or something for the repair kits? I am afraid that I cannot find them anywhere

Dont the pistons need to be compressed again

I installed this Dan Cãtan Throttle Body Rebuild kit myself on my 2000 BMW yesterday The task was quite simple, and only the removal of these original slide bearings, which had been in place for over 20 years, was a bit of a challenge. It was difficult until I realized that an 8mm bolt sawed into a 20mm slot on one end would work very well as a bearing removal tool ;-) Also, I noticed when disassembling my own BMW that the pulley ends didn't have the shims Dan Cãta described that I had to find elsewhere, so the mounting shoulders for that axle would have been perfect for another installation in the future. Otherwise, this operation was easy to do, and the end result now completely satisfies me. Different from the way of making this video, I myself used the old bearings as a "spacer" according to Dan Cãta's advice when installing the new bearings, as well as a long 8mm bolt that extended completely through both holes, so the chances of failure were minimized when the new bearings were hammered into place. The original problem was the TPS which I could not adjust to the set margins under all conditions and now works 100% fine.

loc tite

Excellent video, thanks bro !

I’m going to be doing the clutch on my 2003 and 2006 k1200 GT’s

video would be half the length without all the "uhhs uhms"

6-hours to change an air filter disassembling this plastic...unacceptable! I am selling this fiasco!

My BMW x3 2014 328i don’t have the LED board 😮

Can anyone confirm this works for F11?

Please link me where the hell you found that 30mm socket.

Да хренле у вас там эти оси стоют копейки хоть каждый сезон меняй, у нас в России попробуй. Стоимость такая что купить мопед на эти деньги можно.

Soldering the board is not a permanent fix, the whole board should be changed with a more reliable circuit board to feed the LEDs. LDD-500HW is what you require.

nice job)

Thanks

Do the pistons not need winding back?

Great video !!! Would you recommend the Barnett Clutch Kit?

Buddy, where do we buy that ballast?

great video on the throttle body rebuild! thanks for sharing!

Nice job... thanks...👏👏👏

I’d like to only change the spring, i can leave the position sensor in place in order to avoid adjusting it?

❤️👍

Thanks you...!!!

If you call up and ask bmw dealer, they won't have any clue about this. If they did, they were not willing to tell me.

Thanks, really appreciate your video, easy fixing!

Can barely hear it...

Thanks. BTW, if you look at the cams, they have a flat surface, if both are aligned with each other (with a ruler for ex) so no straw is needed...

3 of the 4 taillights went out. I rempved all 4 and to my surprise not one has this LED chip board in it, or even a spot for it. Please help if you can. X3 2013

How many hours jib

Great content I need to consult you with an issue I have with my 2006 k1200 GT. How can I reach ?

Excellent instructions...Thank You!

Hi, Is it possible to fix 1-series (2011-) f20 the same way ? Thanks a lot

Great video

How about the gear boxes wear? I'm rebuilding many of them all weared out and BMW would sell the whole gearbox....

Good video but always measure the valve clearance exactly on the cam. Do not insert the feeler gauge from the side. Greetings from Germany, Bernd