Видео

Nice trucks

I’m having the same problem but it’s when I’m accelerating or pressing the gas. I never had any issues until I had my AC compressor replaced, that’s when the squeaking started to happen. What it might be?

Still have it? Looks fun what state?

What modifications did you have to do to the transmission hump and in the video is the seat all the way back?

Don’t know how you can stand that music.. cool video

I did a similar swap into a gmt800 truck using a 93 nv4500. I transplated the clutch pedal and with some modification I got the gmt400 pedal to work. I have a stroked lq4 as my engine and I couldn't get that low oil level sensor plug back in with the external slave Did you have to do away with it or did you find a way to make it work?

is it expensive ? i got ram rims 10 inch wide and tires 7 inch been changing tires since 80s as a kid never failed till now is it super loud ?

Thanks I’ve been trying to figure out how to fit the whole shifter on my truck !!!

That red is definitely the wrong shade of black

You filmed a video on filming nothing 🤦🏻‍♂️ You should of just sat behind a desk and talked 😂 You showed how to do nothing

What did you do to make the speedo work? Thank you

I did all this with my sisters 1.8 cruze put the donor engine back in didn't crank over or start so I went on to troubleshoot and came to find out the engine harness was burnt out so I replaced the engine harness and it fired right up😂 good job on this I wish my experience went this smoothly 😂😂

So u are saying my 80 lb kid will not be disappointed. I decided to go conservative knowing that he will outgrow quick and then sister can use it. Last thing I want is too much power.

Hi, I had the exact same whistling noise on my 2019 Chevrolet trax 1.4l. I also had the belt tensioner replaced and the problem was not fixed, but after watching this video I ran to check the spark plugs and one of them was loose and had oil on it, I cleaned it and then tightened it properly and the whistling problem was fixed. Your video was really very helpful, thank you so much for sharing.

I’ve watched several videos of this process and it seems the most involved here. The rusted down pipe was an aftermarket pipe, correct? The PPE is stainless looks like. That should last longer.

4 Lane race pit was the best part about frcc

Is that a vehicle

Yo no way that's me I'm an orange brute Force four-lane race pit frcc the best place to be

Yo no way that's me in the orange brute Force four lane race pit frcc the best place to be

Do you have part numbers on flywheel and clutch kit throw out bearing? Or make and model Thank you sir

How long does it take to put a used engine in

That shit hurts right in the stink hole everytime in grinds 😭

Thanks for your video I just bought right hand drive in Australia and will be starting to work on it very soon Cheers for the tips Dave

How many hours do you charge assuming no issues with siezed parts etc?

Underrated on the likes! Killer video brother! Thanks!

Soo cool

Hahahha awesome - had no idea you were in SK. Started following because of the nv4500 swap.

🤬💯💯 hell yeah that's what I'm talking about down and dirty throwing shit every fucking place dog 💯💯💯💯💯🤬🤬🤬💯💯💯

🤬💯 beldum break them fix them then start over again 💯💯💯💯🤬🤬🤬🤬

💯🤬 hell yeah keep it up buddy you got some good videos 🤬💯💯💯💯

💯🤬 I seen them all terrains you need to shake those and get those mud terrain the only off-road tire 🤔💯💯💯💯💯💯🤬🤬🤬🤬

💯🤬 dog that's badass how the fuck did you do that 💯💯💯💯💯💯💯🤔🤔🤔

💯🤬 one hell of a good looking back road 💯💯💯💯💯💯💯

💯🤬 hell yeah Russell nice-looking lot you got there I see a whole bunch of Chevy sitting around 💯💯💯💯💯💯💯💯

What size bolts hold the shaft to the transfer case can’t find any online

Cummins only V8 DIESEL suck assssss

💯🤔 nice tires but you wouldn't believe how many I pulled out with my suburban mud terrain Dunlop the only off-road tire 💯💯💯💯💯💯

💯 hell yeah Russell I don't think you needed those tires in front of those cars though just a little more gas brother

That is pretty fine transmission and nice over drive.

Short, to the point, and tells me what I need to know! Thanks a lot brother!

Finally got some power from that old 350

This on top of

Nice 👍

Do the front axle shafts seat somehow? I changed the u-joints but putting the shaft back in seems to go in all the way to the u-joint and it doesn't feel like installing a drive shaft. It just feels like it is laying in the tube.

Now THIS was a good video. The rear in my ‘86 K10 blew so I went from the 3:08s to 3:73s so obviously I have to do the front so I’m doing some research before I get into it and this was just a good straight up video so thank you for that

About how tall does your truck stand with the boggers plus 6inch lift? Awesome videos keep em coming . Great work

So its been 2 years since this was made so that should be plenty of time to know the answer to this question i have. I am reading theres a discrepancy in depth to the input shaft between the LS motors and the old motors. The bellhousings are the same, but the LS motors have a different input shaft length that the stock pilot bearing cannot support. (Im not saying it was replaced with a stock bearing, just that im reading it will fail if you do). Did you have a premature input shaft failure on this truck with that bearing or did it work out ok? Supposedly the ls2/ls7 pilot bearings would support the input shaft adequately.

Did you have any work done to your NV4500 before you put it in? Or do you usually go pretty easy on the thing? I’m putting one behind my 6.5 diesel and hear horror stories of other people’s breaking

Thank you sir 😊

82