Видео

I notice you left out the part where you pressed in the differential insulator bushing… Fml

It’s easier to do it on the inside instead of the outside of the home. Also cheaper to replace the holes made in the wall. Keep the outside of your home water tight.

This happened to my house cause of the hurricane recently…. Hopefully we can figure it out thanks for the vid gives me hope the house wont collapse and can actually be fixed.

Hhhmmm. I have this same situation with an 1800s wood sided rear L-wing on a brick house, but my idea is to remove a top board and a board midway or so down so that I know where the lower cavities are that were created with the cross beam supports that I am fairly certain are in there. Would love to hear how this has worked for others in a similar predicament. And also any info on mold/rot that filling these kinds of voids with cellulose or shredded jean insulation may have/may have not caused due to not having a vapor barrier due to not wanting to destroy perfectly good existing walls inside or out.

Thank you, need the chicken and fish bait.

It. Would be nice if you can just get to the point

LAME

Again just reading comments no shown results. Leaving.

Buen vídeo rey, fue bastante útil.

Thanks

What an annoying voice!

Why not take off that piece of siding then drill

Great video. Thi was my first video to start my researc on doing this on my1958 ranch. So with cellulose you do want to PACK as much on as possible vs batt insulation is just fit in place. Good to know.

How do get the broken bolts out

Ur the man thank you

God damn how rusty

What is the part called that goes into that large round hole?

dude you didn't demonstrate how far up the cavity the insulation is blown. which makes you, a what? what do you call that when someone says they're going to do something and they don't do it? lol. a liar!

no sway bar?

Excellent video, straight-to-the-point with good tips and not a bunch of unnecessary BS fluff, thank you brother

How did you get the busted bolts off?

hey there! i'm just curious- do you know what purpose the yeast serves?

Hi great video 👍🏼. Can you please let me know the name of the blower machine that you are using to blow the insulation? I checked my local hardware stores and they don’t have it to rent thank you.

What about a moisture barrier

shouldn't the moisture and mold issue be repaired before adding insulation ?

Good job on piece of shit car ,I have the same shits 😁😁😁

Love your video as I have a hip roof house but I cannot find anyone that has T channel. need help please. Thank you.

I'd like to know about how long this took to get the subframe replaced in total.

I realize this is an older video, but its just what I've been looking for. I gotta 2009 caliber sxt needing the rear subframe replaced and it looks like a heck of a job. You gave me some really good tips on disassembly and I appreciate it immensely. Didnt see anywhere on how long it took you to complete the job. Guessing at least 1 solid day. Thanks again for a great video.

Sorry I do not hear exacly what engridians are? can you write?

How do you get the insulation into the top of the cavity with the holes so low? Do you drill more in the top or do you push the hose up toward the top?

Can you or anybody tell me a good place I can get a subframe and how do I know if it’s good quality or not? I’m seeing a lot of different prices, what would the difference be?

Curious how you got the two broken subframe bolts out. I'm in the middle of this job right now and am having a hard time removing the two broken bolts.

How much this work cost

Be sure to check out more of my husband's channel ❤️❤️❤️

Very good video, curious on how you patch the holes, just replace that entire board and paint it I'm assuming and ignore the 3/4 tongue and groove planks they used to use before sheathing ? Also, are you in CT, Im looking to blow in mineral wool sidewall, can't find it anywhere

Need to do another one! I have plans for it 😉

I like deer meat.

How much of each ingredient do you need to use? …and is the tequila mix used for its sugar content? Are there different kinds of fruit juice that you can use? Thank you

looks good workaholic doing a good job

Fixing these rust issues is not for the faint of heart. So many of the younger generation would not have the physical strength to tackle this project. The one thing I would add is before you jack the car put a tarp down on the grass. It makes finding dropped hardware and tools much easier to find.

Yum.. Nothing like cowboy chili on a open fire.. I have never had deer meat but it sure looks delicious! 😋

Hello is came over from "Urban homesteading Channel" and we love your hoop house design! 💯 New Sub from Texas! 😉

Yeah That One Was Easy Beacause That Jeep Not A (4×4) The Other's Jeep's Compass 4×4 is More Hard To Do it,🙄

Thank you crazy old man, this gives me a great idea to make to make a raised bed with five foot 4x4 at the back (trellis idea)and 30 inch 4x4 in front. This will keep my crazy old lady somewhat happy until she wants more of them. 👍 👍 🇨🇦 from another crazy old man....remember its the wife's fault that we are CRAZY, with the HONEY do list

Very funny Guy 😂 "unless your iron counts low keep your mouth shut"

Perfect...

Great sense of humor!

Thank you for this video it helps me understand the process. I have a 1960 brick home. There is NO insulation behind the exterior walls. The walls are so cold 🥶 in the winter you can feel the coldness even around the electrical outlets. I have sealed everything and even put plastic over all the windows. The exterior walls are still cold to touch. I was thinking of vinyl siding the exterior all of the house except the front. Someone mentioned this process to me instead of covering the brick. I am doing research 🧐. Thanks again for sharing.

Thumbs up but ... Had to stop and re-stop to see how you cut the T-channel.