Видео

hello, please man what is called that part, i want to order it, ebay link does not working. thanks for the way..❤

Brilliant video mate. Many would get stumped after actuator and solenoid work. You've shown another possible cause of the 4WD flashing light problem. Keep up the good work.

Turbos and coolant leaks everywhere

Nice hood exit exhaust

Top man. I have a 96 bongo outside running like a dog so will give this a go.👍

The fuel consumption isn't great is it. I had to buy a V8 just to make it look better..

Very helpful! Well explained. Thanks.

Nice. You'll run out of green lanes in no time.

Hot, moist gas will condense on a cold exhaust pipe and can eventually block it. The lagging will help prevent this happening. The longer the pipe the more chance of condensation.

Hi ferry boat good one now

Hi what was the part number for the bipolar transistor I'm having trouble sourcing one they tell number doesn't match Cheers

Great video thanks

Your charge pipe diverter valves are not connected to the inlets cause you got caps on them right. What did you end up doing to those diverter valve hose? Is it just unplugged freely?

Can I buing sir plz tell me

Plz I requested u guide me how buying this van I live in Pakistan plz guideline me

Hi sir hru

Wonderful, my friend

Long time ago, did you add sealant around gasket when fitting cheers

Cheers fella for all the helpful videos of you working on your Bongo, good to have someone run through it visually with a good camera set up, angles and editing. Is there a video on your mate replacing the crank pulley, what's involved and all that? Thanks

Hi. Top work. Another posted asked if you'd a part number, and though you posted the ebay link twice, that's now gone extinct. Is there any chance you'd have a part number?

Great video, thanks

Hi, did you do a video showing how to remove the old stereo and clock?

It'll glow when the lights are on.

thats because its to much water for the channel it goes into lmao

Hi. Watched your video on fitting an isolator switch for the diesel heater. It was very helpful. Did you buy any random type of switch or does it need to be a specific type? Do you have any of the spares going free? 😉

I have on both connector 12v in 2H position and 0volt on 4H position thats correct?

handy video ...nice to know as i have brakes to do soon

Well done. Did seals and pads last week for the MOT.

Briliant. Good one. 👍

How did you get the electronic gear shifter in the e92?

5 mins in and this is already the most helpful video ive seen for installing the leds

How did you attach it to cage thanks 😊

Друг мой, ты молодец ! У меня тоже мазда бонго френди)

I literally had every one of these 😂😂

hi mate can you send me a link for that Q4 resistor, that link for ebay is void now cheers

Looking at buying a bongo, any advice?? Enjoying the vids…

A non return valve on the 4mm side will help with any fuel pump starvation you may be getting.

Hi is yours 2.5 D?

What shocks did you use ?

Ridgemonkeys are great,its like a double sided pan,worth every penny

Thanks for the video mate, there's so many of these cars having an issue with the 4wd system. I had to replace the solenoid when I got mine 3 years ago and now having the same issue. I replaced the solenoid recently which did nothing so I'm going to remove the vacuum system and install an auto lokka into the front diff. I'll have to make and fit a plate to hold the pin out of the center to keep it engaged. Your video was shared on an Australian Facebook page for the mighty Challenger

Where did you get the springs? What way did they settle is there still a decent lift

Need to do this shortly... thanks for the video - gives me hope!

Your Land Rover repair videos are a lifesaver! I've been grappling with a persistent issue on my TD5 involving excessive black smoke and noticeable power loss. Your expertise in troubleshooting and fixing Land Rovers has been evident in your content, so I was wondering if you could shed some light on this particular issue. Your insights could not only help me but also countless others facing similar challenges. Looking forward to your thoughts on this!

I cant hear clearly what youre saying. What clearance did you use for the intake and exhaust? In mm or inch?

more bongo vids......please

know the feeling ....had the themostat housing pipe outlet errode ....caused the coolant to spill everywhere .....lucky i was not on main roads and 2 mile from a station so lucky no crack head or gasket.

I just leathered the steering wheel with the same problem 😅

Love your bongo vids bro defo helped me with mine, ‘bongo wave 👋’

Is that a far infra red heater on the ceiling? I have one as my main source of heating in my sitting room and it's great: don't need any other form of heating on even during this last cold spell. I've just bought a smaller one to put in Vera, my Bongo. I want to put it on the ceiling, she's a tin top, but not sure of the best way to install it. I'm an almost 70yr old disabled woman doing the conversion on my own and it's definitely a steep learning curve! Videos like this have been invaluable to me these past few months, but I'm wary of anything to do with electrics (even though I once re-wired a whole house!)