Видео

Where is the next video?

My mate drilled holes in his intake to allow more air, can this replace just buying a better one?

I got mine up to 45 miles an hour, but you have to worry about the tires. Do you have high-speed tires on your bike?

Way too many steps IMO to clean mats with your fancy do-dads. But no leaf blower or other quicker drying methods? Hmm

He seams like a nice kid, and he is smart he is teaching people straight up and easy . keep it going brother

Great quality video. Keep it up. Music is too loud

That's the air filter, NOT an intake manifold.

A ported and polished piston for a lot more HP? Yah that’s it! 😅

Good video. At 6:11 in the presentation there is a bad link in thee chain that the valve stem is pointing to. Always inspect the chain. Jim

Drill holes in the intake to allow more air.

So what I did with my stock exhaust is: 1) I took the baffle off and cut the skinny pipe, 2) I put the baffle tip back on to keep back pressure, 3) I drilled a few 1/4" holes near the bottom around the outside. Drilling the holes was a bit of a risk, but it made a 2-3mph difference in my limited testing. This was it keeps some back pressure, doesn't sound too loud, and gives you more power.

Another one is tire the ratio of tire size sprocket and motor sprocket all different if you change just the tire size... as well...

the bike brakes and the chain gets hard without putting or using the brake, how do you fix it?? Is it possible that the motor is tied or the cloucth is stuck??

I jus called you a kid..i found your old vids.. helpd alot.. but your a young man now.. keep it up..

Kid.. you are doing a very good job.. you'll be a good teacher. You explain things very clear and simple.. and I'm 35. I subd

I am old very poor on fixed income working on a chain shifter motor side, that you can bump-start as well (no videos yet but there are pictures on my YT community page) but it keeps on changing, its a work in progress

Hey guys, My carburetor is leaking gas from the cover area which i think is called a float. Its the NT carburetor with the red cover. I checked my donut it has no holes and it wasn't stuck. Any advice?

Step 2: ditch the money pit and get a bus pass

Great video! Your natural bro, you provide value without trying to say a bunch of b.s and come off fake. Kudos! 👌🙏

Young man you are a wealth of practical knowledge. Congratulations!

Thanks man! 👌🏾

Your intake manifold is after the carb bolted to the block. Keep wrenching kid. You got it. Also you port the head intake/exhaust. To make them bigger. Lol good to see kids getting after it.

😎

Sorry, but an expansion chamber would be better. A better speed gain would be to use a smaller sprocket on the rear wheel. These are smarter and proven to actually work.

I really like how this young man has this much knowledge about engines and exhaust. This is very impressive, and it makes me very hopeful for the future. We need more hard working young men like you in this country! Good job, sir. Thanks for working hard, and teaching others your knowledge! EDIT I might want to buy an expansion chamber... How much does that help for torque?

Everything you said about back pressure is completely wrong. Go read the Jennings book.

Go get the Jennings 2 stroke tuning handbook.

Great video & advice... Keep up the good work dude 4 yrs later

your audio is aweful you need to get a mic like tackstar 598 and dontm use music it just interferes

Fhhf

The easiest way to gain speed is to drop body weight 👍

Add nitro methanol to your fuel oil mix for at least a horse power more just a cap full to a 1.5 litre tank of gas plus what ever oil mix you use .

What type of bike is best to put an engine on?

Start uploading again 😠

Could I just use my stock Derailer and sprocket so I can change gears?

Ahhhhhhh......... Skiiiiiiiiiirrrttt!!!! Hold up! Pump the brakes here just a min!! I need to just state the seemingly obvious to me but apparently not to anyone else, fact that bro! Unless you have your old man or older brother or something doing some editing or video coaching, this is a pretty darn good video for your age. That's what I was thinking when I first started watching this. But then by the end of the video I realize that no matter what your old man or possibly older brother was doing in order to have such a well put together and well spoken video etiquette as you have here, that doesn't come from just coaching that comes from something inside and just all in all skill in a profession! So I don't know how old you are dude but I just had to throw this out there like I said cuz no one else seemingly did but you are going places bro! LOL I mean seriously you have managed to put together a better quality and better spoken, meaning keeps the viewers attention and has a little hint of Comedy but still enough seriousness to keep the viewer engaged then I would say probably over half of the videos on youtube! But all right I'll quit praising you, just thought I'd say that you doing a great job bro and I for one personally am pretty impressed and I haven't even made it through the whole video yet! LOL. So keep it up little man, you've got a future! But just a little word of advice, you better lose that little friend of yours who keeps losing your stuff! Just speaking from personal experience that I'm sure anyone here could also agree with and tell you that he's taking you no where but DOWN! LOL "No, no I'm just kidding." (Kind of!😬)

For ur guys info the exhaust won't break without the cap its welded very strong kid just chatting they dont break without the bafgke

Ain’t no way it’s that easy

Cable broken sheep

Cuz dw here in Aus we don’t need that shit w just chop the pipe on the exhaust and no piggy catching u

Thats quite the breakdown. Hope everyone is ok!

Damn

That’s how the og exhaust are today and it’s the best way to do it on a 2 strome

Hey if you want the best exhaust just cut a half inch off the top of the pipe inside and drill holes in it

LT5 swapped Motorised bike when ?

The exhaust is called expansion chamber

This is a great video. Lots of knowledge. And you have an awesome way of explaining things. Really good production too. Way ahead of your time kid. You're definitely doing what you're meant to.

hiya i have the same engine on a push bike can you show me how the coil is wired up .ie i have a blue a white and a black wire coming out off the engine and a green and black wire on the coil .if you could be so kind to show me how yours is wired up,as i say i have the same engine .Thanks .

I agree with Finn