Видео

Do you know where I can buy the alternator cap from

That didn't help me do the job. Im not sure why you didn't just record yourself doing the job and explaining as you went. Instead you made it very confusing. Im sure if i got past the confusing part maybe i would see what i need to see but theres already way too much info in my brain to go any further with this one. I appreciate the effort though. A+ for that.

You need to go counter clockwise.

too dark cant see what he is doing

The little boy at 4:59 is me!

Thank you for this video. I watched several and not a single one mentioned the tub nut was reverse thread. It came right off when you turn in the proper direction!

i cleaned those area, still no suction! Is the machine done? I paid about $200 for the machine from sears maybe 20 years ago, not worth repairing! any helpful thoughts before i toss?

So you don't take the Plastic See Thru Guide Off? You just stick that hanger into it to remove the Gunk stuck up in there? There was another video that should how to remove that, BUT the caution was the screws may not screw in correctly because of the plastic. THX for the video.

So you can easily just undo the screws from underneath, and that whole thing comes off and you can literally just wash it out. Or if there’s no suction push the ball down

Ty for the video

yu didnt even show how to do it

Super badass !!! 🤟🚘

Awesome video brother this will save my unit I just need to quit lending it to people because the last few times I did they brought it back to me filthy as Fk🤣✌️ lesson learned.

Use an air compressor to blast all the gunk out of the brushes. Fast and easy.

What cleaning solution do you use

My alternator just died with over 228k miles. Not bad for a 14 ford focus.

Spoke well and I like how you gave the sizes of the sockets and how you removed the two connectors. Thank u.

Hi, this looks like the exact model I have. I bought my Hoover Steam Vac Ultra in 1999. The other day, I was in the process of putting it back together to store, since everything was dry. I dropped the Recovery Tank. All the parts separated: handle, hinges on either side. From what I can tell, it will still work just fine, but I’m having trouble knowing which hinge goes on what side of the tank. Is there any way you can show me up close how they’re attached? Thank you so much!

It would have been really helpful to see you remove the old broken handle

Thank you for this great video.

I have a simliar sound going on and when I shut off the van, a puff of rusted particles can be seen coming from the center of the alternator pulley. So yeeeeeeeah, time to R&R the alternator! LOL. Thanks for doing a video so I could pinpoint the sound.

Outstanding video. I'm using this as a guide with trying to deal with a frozen nut on a GE unit, nothing has worked so far, including using an impact gun, map gas... nothing... so I'm going to try drilling it tomorrow and see what happens.

So my husband broke that delicate connector. How do o replace it ? Is there anyway I can strip the wires and reconnect ?

Thanks for taking the time to post this video. I was working on the same repair as you and after trying unsuccessfully to remove the spanner nut with penetrating oil and heat, I pulled out my dremel, attached a cutting wheel and had the nut split and off in a matter of minutes!

El enfoque lo mueve mucho

Thank you very much!

Thanks man! Great help. Got mine for free, this problem exactly! Have a great day..

How to change the belt

Make sure to vacuum before using the carpet cleaner

Very helpful but wasn’t my problem. The white rubber collar that is attached to the unit and the suction tank slides into had become detached and out of sight in the workings of the machine. I retrieved it, cleaned it and slide it back on. Great suction again now. I wouldn’t have noticed it had become dislodged without your video.

I needed to replace my drive block. Here's what worked for me in this order: Light tapping. More tapping. Liquid Wrench. Increased tapping and more liquid wrench. Banging, liquid wrench and propane torch. Crying. Cussing. Some amount of beer. Then I had to remove the inner tub which was stuck on the shaft. I repeated all the steps above. Finally, what worked was banging down and at a slight angle on the drive shaft itself. I couldn't get it to actually rock back and forth like so many people could. Replaced the drive block and seems to work fine now.

Smoothest of moves

Insane footage

Why is there so many dislikes to this video?? Bunch of hatters

Thank you found the door for stair attachment was ajar.

Twenty years old? Just get a new one

Fisting... I mean new alternator is 3 hundread bucks :)

Good 👍🏻 video . This happens cause you need to vacuum first then rug clean but it will need a cleaning regardless in time.

Good information, but I was getting seasick watching it, ha ha. Also, at 2:28, was that a Stanley or Craftsman "wood" chisel you the were using? Hope you didn't really dull the working edge on it.

I think the first one was actually a Melt Banana concert

I'm not a handyman. 🙄

This washer is from 1993

Man that is scary,i have never had anything not come out with Kroil,my go to helper and the heat didnt work either? thats ever more crazy,lol,, i work in a shop and we remove huge nuts that have a ungodly amount of torque and once you put that heat on them they give up right away, this one here is for the books for sure.

Or y’all could just remove 3 screws and remove that shield

Buddy I know you meant well but, the video was poor quality all the way. Shaking too much.

Dude thanks

Has anyone had the problem with the hose behind the recovery tank becoming disconnected??? Any idea of a fix???

What were you using as the stethoscope?

Do you know where those the single wire connector goes to?

Hi I like your video I used to have the same machine one your showing on your video this steamvac did great and last for very long time to