Видео

Back screw are not coming of,they are not even screws,looks is been welded,why on RUclips is always is easy but not in reality 😢

Anyone knows how to fix Error 13 on this machine, would really appriciate any help on it!

I thought jura said 500 mil solution 🤔

In Princible 1A but what for Special Screew Driver you Need ? The most of them are Torc but on the rear side (down) we have two special Screew ... anybody has a plan what for a screewdriver you need? Found it Ocal screew .. the same like Impresse 90 S ;)

Witam mam pytanie chodzi o to czy rurka z uszczelką która wychodzi z zaworu drenarzowego w kierunku tłoka dolnego zaprzecza musi wchodzić do wyznaczonego miejsca w dolnym tłoku zaparzacza razem z tą uszczelką bo u mnie jest tak że gdy kręcę max w dół to widać tą uszczelkę od rurki zaworu drenarzowego tak jak by nie wchodziła do końca w wyznaczone miejsce dolnego tłoka zaprzecza ?Czy popełniłem błąd w składaniu zaprzecza a jeśli tak to gdzie ?Z góry serdecznie dziękuję za odpowiedź i pozdrawiam chodzi o Jura Ena 8

Hello, I have a problem with my jura ena8. The machine grinds the coffee and the coffee remains in the coffee glass. Everything doesn't go into the brewer, it stays in the coffee glass and around the brewer.

THANK YOU!!! I looked up a few videos on how to remove the side panels and this was fastest and least destructive. The other videos showed other ways that could possibly break the panels. I used a hammer and a wooden flat spatula from my kitchen!

Please fill the water tank and confirm with OK on the screen.

Hello, my machine gives a warning to add water as soon as I turn it on. I cannot access the menu in any way. What do you think is the reason?

I disassembled and cleaned the entire brewer unit. Put it back together and turned the machine back on. Now, when brewing coffee the water just falls into the drip tray behind the unit, not touching the coffee grinds. The coffee grinds then fall, dry, into the drip tray. Any ideas on what went wrong? Any help would be greatly appreciated. I have a Jura Ena 8.

❤❤❤

❤❤❤

Hey i have the same model but im missing the first 2 parts that u took off , does anybody know where can i buy them ? Tnx

Question - We have a Jura ENA8. The bean cover handle just came off. Is the handle/knob just glued to the top of the plastic cover or is there a secondary plastic piece on the underside that hold the handle in place? Thank you in advance for the information.

hi. i have this machine, milk pump sounds as normal, delivery spout rubbers & pipe clean & clear, steam is delivered as usual but no milk pulled from the tank. looks like could be the pumps not pressurising for suction. any ideas please

Thanks for the video, I wish to have you as a brother in law.

I want to deep clean my minuto and drift my car right now….

wat voor schroevendraaier is dat voor de eerste 4 schroeven

my machine is making me crazy... in the right side switch, the red light is blinking and I don't know what to do... I turn the switch to the left, hear air is coming out and then stops after a while, then turn switch back to the right... still blinking...

How top open a Ena 4, 2021 model?

thank you !!

Thanks for the videos you make 👍 Easy to understand! As I don't have this machine, would I be correct to assume that disassembling the side panel like in the video, I can get a better reach of old, build-up of ground coffee and potential mold, and making it easy to maintain longterm?

After watching your video I got inspired and found a wooden plank instead of the metal plate. It did the trick, opened on the second strike with the hammer! Perfect, thank you

Any idea why water is leaking out of the sides of the machine instead of brewing coffee? I replaced the drainage valve, but the issue persists. Thanks for any advice!

My j8 is stuck on “machine is heating”. I’m going to take it apart and try to troubleshoot myself thanks to your great video! Thank you! 🙏🏼

thank you

Hello and thank you for this very instructive video. Could you please detail the tool you are using at 01:13 to get the 4 screws out. ++

Keep the camera still!!

Thanks for this video. I had the water level warning despite the tak was full. I bought my ENA4 at a Cash Converter Store and they did not have the cardboard packaging. I think that the Jura was shocked in my trunk. After opening the covers I saw a small PCB board moving freely... That was the sensor which operates through the plastic cover. Once fixing it with a tape, everything works, no more error message.

So you break the locks?

Thanks for the vid!! I'm stuck with getting off the left side panel, feels like it will crack, you did it so smoothly, whats the trick? Also, to get out the circle screws without jura tool, just tighten the chuck of a drill and it comes right out

Super vid

How to fix the monitor? Mine is just White light

Words needed 0%. Information content 100%. Nice!

Did you ever tried to remove the front panel where are the 3 screws located ? Under the Ena sign? Is it doable I mean can we go and clean there or it is all attach and can’t get access?

Thank you for your videos! Sooo, my Jura ENA 8 is "spitting" whenever I make coffee or hot water. It sputters and I have opened up the side and cleaned out the excess coffee grounds plus used the Jura cleaning capsules to try and make this go away. Awy help on how to fix this problem is greatly appreciated!!! It's driving me crazy!

😂😂😂😂wtf

Hi there, Would you have any clue why my exact same machine is not working, on the screen its stuck saying that the power door is still open, only it not open. Now i can't use the whole thing because of the message on-screen? Any advice would be very much appreciated cheers

Can’t believe the complaints about the movement. Be glad for what this is: something free that helps you save hundreds in repair costs. It sure did for me!

The noise in these videos makes them unwatchable.

Um zwei Schrauben in hinterem Bereich zu entfernen, brauchst du einen speziellen Schraubenzieher. Die Dinge sind leicht oval. Es geht aber auch mit Gewalt und etwas Mühe mit ner Zange

Does anybody know, how I remove two screws below at the back panel. I’ve got two rivets instead of screws? Thanks for letting me know

If you can't speak might be a good idea to hire a narrator. Only thing I got from this was how to disassemble the unit and there are some tools (unknown type) that allow you to do it.

Lool good hack 😂❤

Just before you replace the covers, you appear to be pressing 2 buttons. Am I correct and are they resets for the grinder motor?

Can you buy new grinders and from where please?

Kahve makinemin atik kahve kismindaki kahveler yuvarlak cikmiyor, sıkıştırılmamış sekilde daginik cikiyor neden olabilir

I slowed this down to 0.25 x so I could see what you’re doing

Great , could you tell us the tool you are using is it a Philips screwdriver or what?

How do you replace the coffee grinder both sides always say empty. 6:10 6:10