Видео

I wired wheeled my alternator for no reason and it looked brand new lol

It's just fine, nothing wrong with the old G-body shuffle!!!

I've dropped a trans without any kind of jack big ass truck 4spd he ay bitch it was un bolted everything wiggled it mostly free kicked the crossmeber it fell out and onto the ground 👌

50/50 water and vinegar. Done

no. the beadbreaker bends if u use alot of force. jus buy a bead breaker n take tire off wit pry bars

E46 N46B18 engine error "vvt self learning function lower learning range" 2A61, relearning via INPA helps drive another 200-300 km, sometimes after oil changed till 1000km, but then error appear again, relearning was done more than 100 times. Has anyone encountered something similar?

That's not "too thin" it's a plethora of problems... The 2 that really stick out are: 1 - poor layer bonding because either you're cooling it too much (cold environment or high fan speed) or printing at too low of a temp. 2 - under extrusion because you haven't calibrated your flow rate for the filament. Try Orca Slicer and go through all the calibration tests for each filament to get better prints.

use zig zag infil

I replaced my throttle body icv and disa and still have the code 1580…. I’m irritated now any help would be appreciated. Although I don’t expect anyone to reply.

Harder in an attic with no floor and a bunch of ducts and cables criss crossing

Got a 20' from Vevor, rated 375 pounds, quite sturdy, more so than I thought it would be...very handy but watch the fingers closing. Best to extend from the bottom to desired height leaving all the unused compressed rungs at the top, then raise into position.

Do u sell them ?

I prefer the "before" 😁

Done it a 100 times with just a floor jack on a gravel floor or on dirt, in my younger years I would just get under there an muscle it, no jack at all.

If you want to laugh... When I was first married a very long time ago, I was out of work and trying to do something around the house and got flustered because I could not find what I needed. I called my then wife's now ex-wife's assistant who had not been to our house and even she knew whatever object I was looking for at the time was located. 20 years later - hysterical!!

I bought one over 4 years ago and it’s only for jewelry, AND THEY ARE WORTH EVERY CENT OF COST!

My welder is just on, the wire comes out automatically. How to settle

Dude said to plug your hole… Flash backs to two dudes on a couch

You were asking about compressors. I used a Craftsman 5HP big tank for years but it wasn't enough for blasting IMHO. I then spent about 1700$ on a vertical air compressor with a huge tank, dual pistons, cast iron cylinders, 230V, and I have plenty of air now. I know it's a bit of an investment, but it will last you many years to come.

Looks like a Mazda B1800

Too time consuming, i'll pay someone else to do it, lol

Would you be willing to build a program for one of these for me and accept payment? I can handle the physical install. How can I contact you?

I did this on my moms oven back in the mid 2000s. Mom never forgave me

After cleaning as good as you can get it!!! Bake the part for 15 minutes BEFORE you put any power on !! THIS IS ESPECIALLY TRUE FOR ANY PARTS THAT HAVE BEEN EXPOSED TO OIL !!! Clean one more time and pre heat part for 10 minutes, pull the part out of the oven , let the part sit for a couple of minutes and apply 1st coat if it’s a two powder system. Bake 15 minutes and apply 2nd coat of 2 part system. The powder coat manufacturers will specify the temperature and duration of minutes to bake !! A CLEAN PART IS YOUR FRIEND ! IMHO…

Oh yeah they look like BEGINNER WELDS

What’s the difference between this and fusion bonded epoxy?

Don’t put aluminum in ultrasonic cleaners. It’ll eat away any corners and drastically compromise strength. Learned it the hard way. Especially thinner parts.

I love c vectra seat bc its pneumatically adjustable in 4 dimensions, buts costs a fortune :D I sold my e36 drift car a year ago :( But i have a seat cordoba in my yard :D its just not comfy

FYI… that respirator is for particulate. You need a VOC filter to protect yourself from the fumes

Where can I buy a heavy load Unistrut Trolley p2950 or more wheels with a width of 35.4mm from wheel to wheel? I bought one on Temu but the description was wrong because it was only 33.7mm and now it wobbles in the Strut instead of fitting snug and running smoothly through...

We need to see the refurb and re install.

Nice dato, just got the engine out of my 1200 ute

Very nice,, good video

No they are not good VAPOR BLASTING is way better

Have the file available?

the part has to reach 400 degrees NOT the oven...for the full cure, within 10 min of that cure, you can check to make sure the powder is 100 covered and no light spots, if you see a light spot take it out of the oven let it cool to 100-120 degrees and reshoot the entire part lightly with the low voltage..then set it back in for the finish again at 400 degrees for the part to cure properly ...oh and wear gloves, your hands have oil on them that will NOT allow the powder to stick properly...

Would it work for a car from the 90

I call BS without f'ing up the rim or pretzeling the bead breaker, but I did the mod that's on yt, bought a proper rim duck and centering ring ( had to make a center ring for my Tacoma rims) and put 255/80-17 on new aluminum rims without a scratch.

Before rpm 7 After rpm 8 how?

I'll ask something stupid but I need an answer! Can you use the oven as a regular oven? Like for baking food?

Yep, I have a locking door to my mailbox that only got one coating of powder about 12 years ago and it's still not rusting.

Need a stronger actuator

Why are you using a wheeled trailer jack for support? So you can move the truck a little while the engine is hoisted or something? If not, why not just use a stationary trailer jack or even just a plain ol bottle jack for support?

Ignore the haters, I wanna try to do something similar as a project

I’m so glad people in the comments are being kind. I’ll never understand why people get so up in arms about people’s welds

Жах!

Not possible 😂😂😂is

Way too much wire between the tip and the metal

Add phosphoric acid dilute it with some water, rust will be gone in no time